Submitted in fulfilment of the requirements of the D.Tech.: Electrical Engineering, Durban University of Technology, 2017. / The tremendous growth in the volume of telecommunication traffic has undoubtedly triggered an unprecedented information revolution. The emergence of high-speed and bandwidth-hungry applications and services such as high-definition television (HDTV), the internet and online interactive media has forced the telecommunication industry to come up with ingenious and innovative ideas to match the challenges. With the coming of age of purposeful advances in Wavelength Division Multiplexing (WDM) technology, it is inherently practicany possible to deploy ultra-high speed all-optical networks to meet the ever-increasing demand for modern telecommunication services. All-optical networks are capable of transmitting data signals entirely in the optical domain from source to destination, and thus eliminate the incorporation of the often bulky and high-energy consuming optical­ to-electrical-to-optical (OEO) converters at intermediate nodes. Predictably, all-optical networks consume appreciably low energy as compared to their opaque and translucent counterparts. This low energy consumption results in lower carbon footprint of these networks, and thus a significant reduction in the greenhouse gases (GHGs) emission. In addition, transparent optical networks bring along other additional and favourable rewards such as high bit-rates and overall protocol transparency. Bearing in mind the aforementioned benefits of transparent optical networks, it is vital to point out that there are significant setbacks that accompany these otherwise glamourous rewards. Since OEO conversions are eliminated at intermediate nodes in all-optical networks, the quality of the transmitted signal from source to destination may be severely degraded mainly due to the cumulative effect of physical-layer impairments induced by the passage through the optical fibres and associated network components. It is therefore essential to come up with routing schemes that effectively take into consideration the signal degrading effects of physical -layer impairments so as to safeguard the integrity and health of transmitted signals, and eventually lower blocking probabilities. Furthermore, innovative approaches need to be put in place so as to strike a delicate balance between reduced energy consumption in transparent networks and the quality of transmitted signals. In addition, the incorporation of renewable energy sources in the powering of network devices appears to gain prominence in the design and operation of the next-generation optical networks. The work presented in this dissertation broadly focuses on physical-layer impairment aware routing and wavelength assignment algorithms (PLIA-RWA) that attempt to: (i) achieve a sufficiently high quality of transmission by lowering the blocking probability, and (ii) reduce the energy consumption in the optical networks. Our key contributions of this study may be summarized as follows: Design and development of a Q-factor estimation tool. Formulation, evaluation and validation of a QoT-based analytical model that computes blocking probabilities. Proposal and development of IA-RWA algorithms and comparison with established ones. Design and development of energy-efficient RWA schemes for dynamic optical networks. / D

It is well known that light can carry two different kind of angular momentum that together form the total angular momentum of photons. These two forms are the spin orbital angular momentum, associated with the circular polarisation of light, and the orbital angular momentum of light associated with a wavefront tilted with respect to the propagation axis. Any tilted wavefront generates an orbital component of the angular momentum but there are some special cases in which this property becomes particularly interesting. It is the case of optical vortices which form when the waveform is continuously and uniformly tilted to the propagation axis forming a spiral structure.

We study the buckling of an oil-water interface populated by micron-sized latex particles using a Langmuir trough. We extend pre-existing results to the micron-range with different capillary length and compare the experimental data to the existing theoretical framework. An unexpected trend for the dominant wavelength of buckling is observed, suggesting that there is a transition between regimes in the micron-range. A mechanism for the new regime is proposed. Cascading is reported, as well as novel kinds of transition between wavelengths within the same particle raft. Lastly, the effect of compression on the macroscopic arrangement of particles is investigated, as well as its effect on the buckling wavelength.

A wrinkling approach was used to study the mechanics of hybrid nanotube/nanocrystal coatings adhering to soft polymer (PDMS) substrates. We focused on three thicknesses: 10 nm, 30 nm, and 40 nm. The approach we used is the Strain-Induced Elastic Buckling Instability for Mechanical Measurements (SIEBIFMM) technique, which allows measurement of the SWCNT film mechanics by the buckling wavelength and the film thickness by inducing a compressive stress in the films at different strains; 2%, 4%, 6%, 8%, 10%, and 12%. In this thesis, dip-coating method with colloidal nanocrystals was used to enhance the rigidity of the carbon nanotube films by filling the pores of the nanotube network. Our results show an almost two-fold enhancement in the Young modulus of a thin SWCNT film related to the presence of a thin interpenetrating over-layer of the semiconductor nanocrystal.

The success of recent experiments to transport data using combined wavelength division multiplexed (WDM) and mode-division multiplexed (MDM) transmission has generated optimism for the attainment of optical networks with unprecedented bandwidth capacity, exceeding the fundamental Shannon capacity limit attained by WDM alone. Optical mode converters and wavelength converters are devices that can be placed in future optical nodes (routers) to prevent or reduce the connection blocking rate and consequently increase network throughput. In this thesis, the specific problem of the placement of mode converters (MC) and mode-wavelength converters (MWC) in combined mode and wavelength division multiplexing (MWDM) networks is investigated. Four previously proposed wavelength converter placement heuristics are extended to handle the placement of MC and MWC in MWDM networks. A simple but effective method for the placement of mode and wavelength converters in MWDM networks is proposed based on ranking the nodes with respect to the volume of received connection requests. The results of extensive simulation tests to evaluate the new method and compare its performance with the performance of the other four heuristics are presented. The thesis provides extensive comparison results among the five converter placement methods using different network topologies and under different network loads. The results demonstrate the effectiveness of the new proposed method in achieving lower blocking rates compared to the other more-complex converter placement heuristics.

This project successfully designed, fabricated and characterized two highly reflective distributed Bragg reflectors for use with long wavelength vertical cavity surface emitting lasers. The first reflector consisted of 20 pairs of alternating lnP/Ino.64Gao.36Aso.777Po.223 layers grown on an InP substrate with a theoretically predicted normal incident reflectivity of 96.6% at a center wavelength of 1550nm. The second DBR had 20 pairs of alternating GaAs/Ino.484Gao.5i6P layers grown on a GaAs substrate with a theoretically predicted reflectivity of 94.9% at a center wavelength of 1550nm for normal incident light. Experimental results obtained using a specially designed reflectivity measurement setup confirmed reflectivity models and predictions at both normal and variable incident light angles. However, these measurements revealed a discrepancy between theoretical and experimental layer thickness values for both DBR structures. Applying perturbations to the theoretical models, the actual layer thicknesses ofthe DBRs were determined. X-ray analysis was employed to examine the periodicity of the super-lattices along with the accuracy of lattice matching to the substrate. Transmission electron microscopy revealed that no detectable drift in layer thickness was apparent during growth of the DBR structures. Photoluminescence was used to investigate any compositional variations ofthe quaternary layers in the first DBR stack. / Thesis / Master of Applied Science (MASc)

This thesis describes the development of optical wavelength converters with an integrated coupling structure, fabricated on periodically poled MgO doped lithium niobate (MgO:LN) for optical fiber communication and other all-optical signal processing applications. Wavelength converter is an integral part of any broadband communication system. The ability to transfer information between carrier wavelengths allows for efficient use of the available bandwidth in a transmission medium. Wavelength converters based on PPLN waveguides are among the most efficient nonlinear optical devices available today, due to highspeed operation, low noise, parallel operation on multiple wavelength channels and preservation of information carried in the optical domain. However, low conversion efficiency is an issue for wavelength converter based on PPLN waveguide. Compared to pure LN, MgO doped LN decrease restriction in optical damage and increase conversion efficiency. Integrated coupling structure demonstrates a solution to mode-coupling of the input wave to the fundamental mode of DFG device and increase the conversion efficiency. Therefore, a periodically poled MgO doped lithium niobate (MgO:LN) waveguides with integrated coupling structure is fabricated. The components of integrated coupling structure are compatible with lithium nobate waveguides, including directional couplers, small radius bends, adiabatic taper, and mode filter. The integrated coupling structure combines the pump and signal waves into the DFG conversion section, and makes the single mode conversion of the pump from input waveguide to conversion section. Theoretical models and simulations are provided in this thesis, and performances of the device with this structure are also presented. / Thesis / Master of Applied Science (MASc)

As WDM results in an ever-increasing trend of traffic concentration, any failure on a single fiber-link or a single switching node will be catastrophic. Rapid restoration can recover the affected traffic so as to make the network more robust and reliable. The conventional restoration methods are designed mostly for reconfiguring the network topology; they are not immune from service interruption. In this thesis, an effective algorithm called backup-path-wavelength rearrangement scheme is proposed to reduce the connection blocking probability in an all-optical network. The proposed scheme performs wavelength retuning on the backup paths to improve the acceptance probability for new connection requests and introduce zero service interruption to the traffic in the network. The performance evaluation indicates that the connection blocking probability can be decreased greatly by the proposed scheme. The combination of BPWR and traffic grooming can efficiently alleviate the wavelength continuity constraint.

No description available.

<p> With the increasing demand for data rate and transmission distance, the trend in fiber-optic communications is to build an ultra-high, long-haul transmission system. One of the challenges in this kind of systems comes from the fiber dispersion and dispersion slope. For the wide-band wavelength-division multiplexing (WDM) system or ultra-high bit rate optical time-division multiplexing (OTDM) system, the dispersion slope could be a serious problem to impair the system performance.</p> <p> Many studies have shown that the dispersion and dispersion slope affect the long-haul fiber transmission dramatically, especially for the high-capacity systems. Most of them recommend to totally compensate the dispersion and the dispersion slope simultaneously. And a lot of compensating techniques are proposed. However, it is not easy to realize the simultaneous compensation for the dispersion and dispersion slope in the practical systems. Therefore, the necessity of compensating the dispersion slope in wide-bandwidth systems should be verified.</p> <p> We focus on the study of ultra-high bit rate (160-Gb/s) single-channel fiber-optic transmission. The results show that the dispersion slope is not necessary for the dispersion-managed system when the optimal launch parameters are given. Then we present how to find out the optimum in fiber-optic systems and a novel optimizing technology, space mapping technology (SM) is introduced, which has been successfully applied to the electromagnetic area. An application of SM in optical systems is implemented. By using this smart optimization technique, lots of computational efforts for evaluating the fine model in optimization process are saved.</p> / Thesis / Master of Applied Science (MASc)