Indiana University-Purdue University Indianapolis (IUPUI) / Investigations of a constant-volume combustor ignited by a penetrating transient jet (a puff) of hot reactive gas have been conducted in order to provide vital data for designing wave rotor combustors. In a wave rotor combustor, a cylindrical drum with an array of channels arranged around the axis spins at a high rpm to generate high-temperature and high-pressure product gas. The hot-gas jet ignition method has been employed to initiate combustion in the channels. This study aims at experimentally investigating the ignition delay time of a premixed combustible mixture in a rectangular, constant-volume chamber, representing one channel of the wave rotor drum. The ignition process may be influenced by the multiple factors: the equivalence ratio, temperature, and the composition of the fuel mixture, the temperature and composition of the jet gas, and the peak mass flow rate of the jet (which depends on diaphragm rupture pressure). In this study, the main mixture is at room temperature. The jet composition and temperature are determined by its source in a pre-chamber with a hydrogen-methane mixture with an equivalent ratio of 1.1, and a fuel mixture ratio of 50:50 (CH4:H2 by volume). The rupture pressure of a diaphragm in the pre-chamber, which is related to the mass flow rate and temperature of the hot jet, can be controlled by varying the number of indentations in the diaphragm. The main chamber composition is varied, with the use of four equivalence ratios (1.0, 0.8, 0.6, and 0.4) and two fuel mixture ratios (50:50, and 30:70 of CH4:H2 by volume). The sudden start of the jet upon rupture of the diaphragm causes a shock wave that precedes the jet and travels along the channel and back after reflection. The shock strength has an important role in fast ignition since the pressure and the temperature are increased after the shock. The reflected shock pressure was examined in order to check the variation of the shock strength. However, it is revealed that the shock strength becomes attenuated compared with the theoretical pressure of the reflected shock. The gap between theoretical and measured pressures increases with the increase of the Mach number of the initial shock. Ignition delay times are obtained using pressure records from two dynamic pressure transducers installed on the main chamber, as well as high-speed videography using flame incandescence and Schileren imaging. The ignition delay time is defined in this research as the time interval from the diaphragm rupture moment to the ignition moment of the air/fuel mixture in the main chamber. Previous researchers used the averaged ignition delay time because the diaphragm rupture moment is elusive considering the structure of the chamber. In this research, the diaphragm rupture moment is estimated based on the initial shock speed and the longitudinal length of the main chamber, and validated with the high-speed video images such that the error between the estimation time and the measured time is within 0.5%. Ignition delay times decrease with an increase in the amount of hydrogen in the fuel mixture, the amount of mass of the hot-jet gases from the pre-chamber, and with a decrease in the equivalence ratio. A Schlieren system has been established to visualize the characteristics of the shock wave, and the flame front. Schlieren photography shows the density gradient of a subject with sharp contrast, including steep density gradients, such as the flame edge and the shock wave. The flame propagation, gas oscillation, and the shock wave speed are measured using the Schlieren system. An image processing code using MATLAB has been developed for measuring the flame front movement from Schlieren images. The trend of the maximum pressure in the main chamber with respect to the equivalence ratio and the fuel mixture ratio describes that the equivalence ratio 0.8 shows the highest maximum pressure, and the fuel ratio 50:50 condition reveals lower maximum pressure in the main chamber than the 30:70 condition. After the combustion occurs, the frequency of the pressure oscillation by the traversing pressure wave increases compared to the frequency before ignition, showing a similar trend with the maximum pressure in the chamber. The frequency is the fastest at the equivalence ratio of 0.8, and the slowest at a ratio of 0.4. The fuel ratio 30:70 cases show slightly faster frequencies than 50:50 cases. Two different combustion behaviors, fast and slow combustion, are observed, and respective characteristics are discussed. The frequency of the flame front oscillation well matches with that of the pressure oscillation, and it seems that the pressure waves drive the flame fronts considering the pressure oscillation frequency is somewhat faster. Lastly, a feedback mechanism between the shock and the flame is suggested to explain the fast combustion in a constant volume chamber with the shock-flame interactions.

Indiana University-Purdue University Indianapolis (IUPUI) / This study contributes to a better working knowledge of the equipment being used in a well-established combustion lab. In particular, several constant-volume combustion properties (e.g., time ignition delay, flame propagation, and more) are examined to deduce any buoyancy effects between fuel and air mixtures and to develop a method aimed at minimizing such effects. This study was conducted on an apparatus designed to model the phenomena occurring within a single channel of a wave rotor combustor, which consists of a rotating cylindrical pre-chamber and a fixed rectangular main combustion chamber. Pressure sensors monitor the internal pressures within the both chambers at all times, and two slow-motion videography techniques visually capture combustion phenomena occurring within the main chamber. A new recirculation pump system has been implemented to mitigate stratification within the chamber and produce more precise, reliable results. The apparatus was used in several types of experiments that involved the combustion of various hydrocarbon fuels in the main chamber, including methane, 50%-50% methane-hydrogen, hydrogen, propane, and 46.4%-56.3% methane-argon. Additionally, combustion products created in the pre-chamber from a 1.1 equivalence ratio reaction between 50%-50% methane-hydrogen and air were utilized in the issuing pre-chamber jet for all hot jet ignition tests. In the first set of experiments, a spark plug ignition source was used to study how combustion events travel through the main chamber after different mixing methods were utilized – specifically no mixing, diffusive mixing, and pump circulation mixing. The study reaffirmed that stratification between fuel-air mixtures occurs in the main chamber through the presence of asymmetrical flame front propagation. Allowing time for mixing, however, resulted in more symmetric flame fronts, broader pressure peaks, and reduced combustion time in the channel. While 30 seconds of diffusion helped, it was found that 30 seconds of pumping (at a rate of 30 pumps per 10 seconds) was the most effective method at reducing stratification effects in the system. Next, stationary hot jet ignition experiments were conducted to compare the time between jet injection and main chamber combustion and the speed of the resulting shockwaves between cases with no mixing and 30 seconds of pump mixing. Results continued to show an improvement with the pump cases; ignition delay times were typically shorter, and shock speeds stayed around the same, if not increased slightly. These properties are vital when studying and developing wave rotor combustors, and therefore, reducing stratification (specifically by means of a recirculation system) should be considered a crucial step in laboratory models such as this one. Lastly, experiments between a fueled main chamber and rotating pre-chamber helped evaluate the leakage rate of the traversing hot jet ignition experimental setup paired with the new pump system. In its current form, major leaks are inevitable when attempting traversing jet experiments, especially with the pump’s suction action drawing sudden large plumes of outside air into the main chamber. To minimize leaks, gaps between the pre-chamber and main chamber should be reduced, and the contact surface between the two chambers should be more evenly distributed. Also, the pump system should only be operated as long as needed to evenly distribute the fuel-air mixture, which approximately happens when the main chamber’s total volume has been circulated through the system one time. Therefore, a new pump system with half of the original system’s volume was developed in order to decrease the pumping time and lower the risk of leaks.

Indiana University-Purdue University Indianapolis (IUPUI) / Testing of a wave-rotor constant-volume combustor (WRCVC) showed the viability of the application of wave rotors as a pressure gain combustor. The aero-thermal design of the WRCVC rig had originally been performed with a time-dependent, one-dimensional model which applies a single-step reaction model for the combustion process of the air-fuel mixture. That numerical model was validated with experimental data with respect of matching the flame propagation speed and the pressure traces inside the passages of the WRCVC. However, the numerical model utilized a single progress variable representing the air-fuel mixture, which assumes that fuel and air are perfectly mixed with a uniform concentration; thus, limiting the validity of the model. In the present work, a two-step reaction model is implemented in the combustion model with four species variables: fuel, oxidant, intermediate and product. This combustion model is developed for a more detailed representation for the combustion process inside the wave rotor. A two-step reaction model presented a more realistic representation for the stratified air-fuel mixture charges in the WRCVC; additionally it shows more realistic modeling for the partial combustion process for rich fuel-air mixtures. The combustion model also accounts for flammability limits to exert flame extinction for non-flammable mixtures. The combustion model applies the eddy-breakup model where the reaction rate is influenced by the turbulence time scale. The experimental data currently available from the initial testing of the WRCVC rig is utilized to calibrate the model to determine the parameters, which are not directly measured and no directly related practice available in the literature. A prediction of the apparent ignition the location inside the passage is estimated by examination of measurements from the on-rotor instrumentations. The incorporation of circumferential leakage (passage-to-passage), and stand-off ignition models in the numerical model, contributed towards a better match between predictions and experimental data. The thesis also includes a comprehensive discussion of the governing equations used in the numerical model. The predictions from the two-step reaction model are validated using experimental data from the WRCVC for deflagrative combustion tests. The predictions matched the experimental data well. The predicted pressure traces are compared with the experimentally measured pressures in the passages. The flame propagation along the passage is also evaluated with ion probes data and the predicted reaction zone.

When studying pressure-gain combustion and wave rotor combustors, it is vital that any experimental model accurately reflect the real world conditions/applications being studied; this not only confirms previous computational and analytical work, but also provides new insights into how these concepts and devices work in real life. However, mixture stratification can have a noticeable effect on multiple combustion properties, including flame propagation, pressure, ignition time delay, and more, and this is especially true in constant-volume combustion chambers. Because it is beneficial to model wave rotor systems using constant-volume combustors such as what is employed in the IUPUI Combustion and Propulsion Research Laboratory, these stratification effects much be taken into account and reduced if possible. This study sought to find an effective method to reduce stratification in a rectangular constant-volume combustion chamber by means of manual recirculation pump. Spark-ignited flames were first produced in the chamber itself and studied using schlieren and color videography techniques as well as quantitative pressure histories. After determining the pump's effectiveness in reducing stratification, it was next employed when a hot jet of combustion products from a separate combustion chamber was used as an ignition source instead of the spark plug - a process typically employed in real wave rotor combustors. Lastly, the pump was used to study the leakage from the system for future test cases in order to offer further recommendations on how to effectively use the recirculation system. This process found that key properties significant to wave rotor development, such as time ignition delay, were affected by these stratification effects in past studies that did not account for this detail. As such, the pump has been permanently incorporated into the wave rotor model, as stratification is a vital. Additionally, significant fuel leakage is possible during rotational pre-chamber cases, and this should be address before proceeding with such experiments in the future. To combat this, the pump system has been reduced in volume, and suggestions have been provided on how to better seal the main rectangular chamber in the future.