Near-membrane and trans-membrane proteins and their interactions with the extracellular matrix (ECM) can yield valuable information about cell dynamics. However, advances in the field of nanoscale cellular processes have been hindered, in part, due to limits imposed by current technology. In this work, a novel evanescent field (EF) imaging technique is designed, modeled, created and tested for near-field imaging in the apical surface of cells. This technique and Förster resonance energy transfer (FRET) were used to investigate interactions between integrins on the cell surface and the ECM protein, fibronectin. The goal was to monitor changes in the integrin density at the cell surface as a function of clustering after binding to fibronectin on the microsphere surface. For the EF technique, quantum dot (QD)-embedded polystyrene microspheres were used to couple light into whispering gallery modes (WGMs) inside the microspheres; the resulting EF at the surface of the microsphere was used as a near-field excitation source with ~50 nm axial resolution for exciting fluorescently-labeled integrins. For FRET measurements (~10 nm axial resolution), QDs (donors) were coated on the surface of microspheres and energy transfer to red fluorescent protein (RFP)-integrin constructs (acceptors) studied. In both techniques, the QD-modified microspheres were mounted on atomic force microscope (AFM) cantilevers, functionalized with fibronectin, and brought into contact with fluorescently-labeled HeLa or vascular smooth muscle (VSM) cells. The results obtained from both methods show the clustering and activity of the integrins and are in good agreement with each other. Amsterdam discrete dipole approximation (ADDA) was used to study the effects of inhomogeneous surrounding refractive index on the quality factor and position of the WGMs due to the attachment of a microsphere to an AFM cantilever. WGMs of various QD-embedded microspheres mounted on AFM cantilevers were experimentally measured and shown to be consistent with the model.

xi, 125 p. : ill. (some col.) A print copy of this thesis is available through the UO Libraries. Search the library catalog for the location and call number. / This dissertation presents experimental and theoretical studies of radiation pressure cooling in silica optomechanical microresonators where whispering gallery modes (WGMs) are coupled to thermal mechanical vibrations. In an optomechanical system, circulating optical fields couple to mechanical vibrations via radiation pressure, inducing Stokes and anti-Stokes scattering of photons. In analogy to laser cooling of trapped ions, the mechanical motion can in principle be cooled to its ground state via the anti-Stokes process in the resolved-sideband limit, in which the cavity photon lifetime far exceeds the mechanical oscillation period. Our optomechanical system is a slightly deformed silica microsphere (with a diameter 25-30 μm ), featuring extremely high Q -factors for both optical ( Q o ∼ 10 8 ) and mechanical ( Q m ∼ 10 4 ) systems. Exploiting the unique property of directional evanescent escape in the deformed resonator, we have developed a free-space configuration for the excitation of WGMs and for the interferometric detection of mechanical displacement, for which the part of input laser that is not coupled into the microsphere serves as a local oscillator. Measurement sensitivity better than 5 × 10 -18 m /[Special characters omitted.] has been achieved. The three optically active mechanical modes observed in the displacement power spectrum are well described by finite element analysis. Both radiation pressure cooling and parametric instabilities have been observed in our experiments. The dependence of the mechanical resonator frequency and linewidth on the detuning as well as the intensity of the input laser show excellent agreement with theoretical calculations with no adjustable parameters. The free-space excitation technique has enabled us to combine resolved sideband cooling with cryogenic cooling. At a cryogenic temperature of 1.4 K, the sideband cooling leads to an effective temperature as low as 210 m K for a 110 MHz mechanical oscillator, corresponding to an average phonon occupation of 37, which is one of the three lowest phonon occupations achieved thus far for optomechanical systems. The cooling process is limited by ultrasonic attenuation in fused silica, which should diminish when bath temperature is further lowered, with a 3 He cryostat, to a few hundred millikelvin. Our experimental studies thus indicate that we are tantalizingly close to realizing the ground-state cooling for the exploration of quantum effects in an otherwise macroscopic mechanical system. / Committee in charge: Michael Raymer, Chairperson, Physics; Jens Noeckel, Member, Physics; Hailin Wang, Member, Physics; Paul Csonka, Member, Physics; Jeffrey Cina, Outside Member, Chemistry

Ce travail de thèse a consisté à mettre en place toute une filière de fabrication de microtores en silice sur silicium (étapes de lithographie et de gravure en salle blanche pour la réalisation de microdisques, installation d'un banc optique permettant la transformation du résonateur en microtore par un procédé de recuit laser CO2), à installer un banc optique permettant de mesurer la largeur spectrale de leurs résonances optiques à 1.55 µm et enfin, à explorer l'intégration d'émetteurs de lumière composés d'éléments de la colonne IV comme du silicium et du germanium, dans ces cavités. Des microtores supportant des résonances de facteur de qualité Q proche de 10^8 à 1.55 µm ont été fabriqués. Ces réalisations sont très proches de l'état de l'art et valident à la fois la fabrication des cavités et le banc optique permettant les mesures spectrales des modes de galerie (WGM). Grâce à un contrôle fin des différentes étapes de fabrication, de nouveaux résonateurs ont également été réalisés, des microsphères de silice sur puce de petits rayons (entre 5 et 14 µm). Une étude détaillée de ces résonateurs est présentée. Des Q proches de 10^8 ont également été mesurés. Des cavités WGM comportant une couche de nanoclusters de silicium dans une matrice de silice avec des ions erbium (SiOx : Er) sont étudiées en photoluminescence. Un couplage des ces émetteurs à des WGM est observé à température ambiante dans le visible et dans l'infrarouge. Un travail de couplage du germanium aux WGM a commencé et semble prometteur. / This work consisted in developing a fabrication process of silica microtoroids on a silicon chip (steps of lithography and etching in clean room for the realization of microdisks, set up of an optical bench to form a microtoroid with a reflow treatment of a silica microdisk by a CO2-laser), setting up an optical bench to measure the linewidth of their optical resonances at 1.55 µm and finally, exploring light emitters integration in these cavities such as silicon and germanium. Very high quality-factors (Q) close to 10^8 at 1.55µm have been measured on microtoroids. These realizations are very close to the State of the art and validate both the fabrication of these cavities and the optical bench to measure the linewidth of their Whispering Gallery Modes (WGM). With a precise control of the fabrication steps, new resonators have also been fabricated, silica microspheres on a chip with small radii (5 < r < 14µm). An in-depth study of these last ones is presented. Q-factors close to 10^8 have also been measured on microspheres. WGM cavities with a SiOx: Er layer (silicon nanoclusters in silica with erbium ions) are studied by photoluminescence. Coupling of these light emitters to WGM is observed in visible and near infrared at room temperature. A work of coupling of germanium to WGM began and seems promising.

I advanced the understanding of particle morphology and its implications for the behavior and effects of atmospheric aerosol particles. I have developed new experimental methods for the Aerosol Optical Tweezers (AOT) system and expanded the AOT’s application into studying realistic secondary organic aerosol (SOA) particle phases. The AOT is a highly accurate system developed to study individual particles in real-time for prolonged periods of time. While previous AOT studies have focused on binary or ternary chemical systems, I have investigated complex SOA, and how they interact with other chemical phases, and the surrounding gas-phase. This work has led to new insights into liquid-liquid phase separation and the resulting particle morphology, the surface tension, solubility, and volatility of SOA, and diffusion coefficients of SOA phases. I designed a new aerosol optical tweezers chamber for delivering a uniformly mixed aerosol flow to the trapped droplet’s position. I used this chamber to determine the phase-separation morphology and resulting properties of complex mixed droplets. A series of experiments using simple compounds are presented to establish my ability to use the cavity enhanced Raman spectra to distinguish between homogenous single-phase, and phase-separated core-shell or partially-engulfed morphologies. I have developed a new algorithm for the analysis of whispering gallery modes (WGMs) present in the cavity enhanced Raman spectra retrieved from droplets trapped in the AOT. My algorithm improves the computational scaling when analyzing core-shell droplets (i.e. phase-separated or biphasic droplets) in the AOT, making it computationally practical to analyze spectra collected over many hours at a few Hz. I then demonstrate for the first time the capture and analysis of SOA on a droplet suspended in an AOT. I examined three initial chemical systems of aqueous NaCl, aqueous glycerol, and squalane at ~ 75% relative humidity. For each system I added α-pinene SOA – generated directly in the AOT chamber – to the trapped droplet. The resulting morphology was always observed to be a core of the initial droplet surrounded by a shell of the added SOA. By combining my AOT observations of particle morphology with results from SOA smog chamber experiments, I conclude that the α-pinene SOA shell creates no major diffusion limitations for water, glycerol, and squalane under humid conditions. My AOT experiments highlight the prominence of phase-separated core-shell morphologies for secondary organic aerosols interacting with a range of other chemical phases. The unique analytical capabilities of the aerosol optical tweezers provide a new approach for advancing the understanding of the chemical and physical evolution of complex atmospheric particulate matter, and the important environmental impacts of aerosols on atmospheric chemistry, air quality, human health, and climate change.

Optical resonators, which confine light by resonant recirculation, serve as the basis for a wide variety of optical components. Though they appear in many geometric forms, the most effective of optical resonators show axial symmetry in at least one dimension. A popular variation that finds broad application is the dielectric sphere. Acclaimed for their high quality (Q) factor and small modal volume, spheres owe credit of these attractive features to their support of whispering gallery mode (WGM) resonances. The sensitivity of a resonance's frequency and Q to strain, temperature, and other parameters of the surrounding medium can be the basis for ultracompact modulators and sensors. Physically, WGMs are special optical modes which can be understood as light rays that orbit the equator of the sphere guided by total internal reflection. Like a smooth stone can be skipped along the surface of a pond, light can be confined to the inside of a sphere by successive reflections. To best excite WGMs, the source light should initially trace a line tangent to the sphere's circumference. But incorporating a tiny sphere with such nanometric tolerances into a practical sensor structure has its challenges and the prospects for microsphere applications have suffered because of the plight of this problem. The work in this dissertation details the fabrication and function of three new "press fit" spherical resonators. These etched fiber micro-devices were developed to meet the demand for a robust, self-integrated means of coupling light between an optical fiber and WGMs in a microsphere resonator. The etching processes have been tuned to enable secure storage of a microsphere while also providing efficient excitation and interrogation of WGMs. Furthermore, the methods have been designed to be staightforward, quick, and repeatable. Using standard etchants on common polarization-maintaining fiber with readily purchased microspheres, the press fit resonators demonstrated here can be batch-fabricated and assembled. The press fit spherical resonator offers an alignment-free and conveniently pigtailed WGM coupler that has great potential for bio-science sensing applications and studies of resonant bispheres. / Ph. D.

[Truncated abstract] This thesis is split into two parts. In part one; A 50 K dual mode oscillator, the aim of the project was to build a 50 K precision oscillator with frequency stability on the order of 1014 from 1 to 100 seconds. A dual-mode temperature compensation technique was used that relied on a turning point in the frequency-temperature relationship of the difference frequency between two orthogonal whispering gallery modes in a single sapphire crystal. A cylindrical sapphire loaded copper cavity resonator was designed, modelled and built with a turning point in the difference frequency between an E-mode and H-mode pair at approximately 52.5 K . . . The frequencies and Q-factors of whispering spherical modes in the 3-12 GHz range in the fused silica resonator are measured at 6, 77 and 300 K and the Q-factor is used to determine the loss tangent at these temperatures. The frequency and Q-factor temperature dependence of the TM2,1,2 whispering gallery mode at 5.18 GHZ is used to characterise the loss tangent and relative permittivity of the fused silica from 4-300 K. Below 22 K the frequency-temperature dependence of the resonator was found to be consistent with the combined effects of the thermal properties of the dielectric and the influence of an unknown paramagnetic impurity, with a spin resonance frequency at about 138 ± 31 GHz. Below 8 K the loss tangent exhibited a 9th order power law temperature dependence, which may be explained by Raman scattering of Phonons from the paramagnetic impurity ions. A spherical Bragg reflector resonator made from multiple concentric dielectric layers loaded in a spherical cavity that enables confinement of field in the centre of the resonator is described. A set of simultaneous equations is derived that allow the calculation of the required dimensions and resonance frequency for such a resonator and the solution is confirmed using finite element analysis. A spherical Bragg reflector resonator is constructed using Teflon and free-space as the dielectric materials. A Q-factor of 22,000 at 13.87 GHz was measured and found to compare well with the design values.

This thesis presents an investigation of the dynamic properties of wide range of interfacial systems, from colloidal particles in solution, through the realm of aerosols and onto studies of molecular adsorption at an interface. The primary experimental technique utilized is optical tweezers. An exploration of the history of the use of radiation pressure to manipulate matter is presented, followed by an introduction to how optical tweezers work. Some of the more advanced methods of tweezing are discussed, with an emphasis on the use of spatial light modulators (SLMs) to realise dynamic holographic optical tweezers (DHOTs), an example of which has been constructed within our laboratory using off-the-shelf optical components, and combined with a spectrometer to facilitate high resolution spectroscopic studies of microscopic systems. The spectroscopic analysis of microparticles is greatly enhanced by optical feedback generated when the wavelength of light utilized is an integer number of wavelengths around the circumference of the microsphere. Enhanced signal occurs at these wavelengths, termed whispering gallery modes (WGMs). The absolute position of these resonances depends strongly upon the shape, size and refractive index of the particle, and is predicted by Mie theory. A discussion of the concepts behind Mie theory, as well as how to use an experimental WGM spectrum to deduce the size and composition of a microparticle, is provided. This technique is then put to use in a detailed study on the properties of single aerosols, comprised of sodium chloride solution, and generated using a handheld medical nebulizer. Studies have been carried out on both evaporating and growing droplets trapped with a Gaussian beam; in the latter case, periods of size stability are observed, owing to resonant absorption of radiation at the trapping laser wavelength. The SLM can be used to change the trapping laser to a Laguerre-Gaussian (LG) mode, and an investigation of how this affects the dynamics of the droplet is presented. It is found that the use of LG modes with $ellgeq10$ produced Raman spectra with significantly more intense WGMs, and also suppressed droplet evaporation. Through observations made with fluorescent polystyrene microspheres, it is argued that the LG modes are more efficient at coupling into WGMs of the droplets. Leading on from these experiments on salt water droplets, experiments have been conducted using ionic liquids (ILs). These fluids have many fascinating properties and potential applications. The optical trapping of droplets comprised of aqueous solutions of the ionic liquid ethylammonium nitrate (EAN) and water has been demonstrated for the first time. These droplets are analysed spectroscopically by illuminating them with the output from a broadband LED; WGMs that are observed in the backscattered light are used to determine their size and composition. The response of the droplets to conditions of varying relative humidity has also been investigated. In order to characterise the relative humidity experienced by both the salt water and IL droplets, the concentration of water vapour within the trapping cells has been measured using diode laser absorption spectroscopy. The spatially modulated laser beam is then utilized in a different fashion; instead of optically tweezing a sample, a low numerical aperture objective lens is utilized to focus the laser onto the surface of a gold coated microscope slide. When a colloidal sample is placed on this surface, the thermal gradients cause the particles to form two dimensional crystals. The SLM is utilized to form multiple nucleation sites, and the dynamics of the crystals are directly observed in real time using video microscopy. It is found that grain rotation-induced grain coalescence (GRIGC) occurs, with the rotation of both crystals before coalescence. Control over the grain size is achieved by altering the separation of the laser spots, and shows that the time scale for grain boundary annealing in our system is in good agreement with theoretical expressions formulated for nanocrystal growth. Finally, as a complimentary technique to the microparticle spectroscopy previously discussed, a bulk interface is probed by using evanescent wave broadband cavity enhanced absorption spectroscopy (EW-BBCEAS) specifically to study the adsorption of cytochrome c (cyt c) to a fused silica surface. Visible radiation from a supercontinuum source is coupled into an optical cavity consisting of a pair of broadband high reflectivity mirrors, and a total internal reflection (TIR) event at the prism/water interface. Aqueous solutions of cyt c are placed onto the TIR footprint on the prism surface and the subsequent protein adsorption is probed by the resulting evanescent wave. The time integrated cavity output is directed into a spectrometer, where it is dispersed and analysed. The broadband nature of the source allows observation of a wide spectral range (ca 250 nm in the visible). The system is calibrated by measuring the absorption spectra of dyes of a known absorbance. Absorption spectra of cyt c are obtained for both S and P polarized radiation, allowing information about the orientation of the adsorbed protein to be extracted.

Les microrésonateurs à mode de galerie passifs à base de cristal ou de verre fabriqués par la méthode de fusion possèdent un facteur de qualité limité à quelques 10E8. Ceci est généralement dû à la contamination de la surface du résonateur lors de sa fusion. Dans ces travaux, nous proposons de contourner cette limitation en utilisant des microrésonateurs actifs pour compenser les pertes. Afin de caractériser les microrésonateurs actifs de très haut facteur de qualité ainsi obtenu, nous nous appuyons sur la méthode CRDM (Cavity Ring Down Measurement). Cette méthode interférométrique est d'une part bien adaptée à la caractérisation de résonateurs de très haut facteur de qualité et d'autre part elle permet de remonter de manière univoque aux facteurs de qualité intrinsèque Qo et extrinsèque Qe du résonateur. Dans un régime de compensation de pertes, nous avons pu atteindre tous les régimes de couplage et obtenus des facteurs de qualité intrinsèques excédant les 10E10. En régime d'amplification sélective, nous avons démontré expérimentalement que l'on pouvait obtenir des gains élevés allant jusqu'à 33 dB et des retards de groupe excédant 2,3 µs dans ces microrésonateurs actifs. Ces microrésonateurs de très haut facteur de qualité et de très haute finesse peuvent présenter un couplage modal se manifestant par un doublet de résonances. Une confrontation théorie/expérience avec la méthode CRDM permet de mesurer un écart très faible entre les doublets. Par ailleurs, ces microrésonateurs présentant un fort confinement spatial et une forte surtension, sont propices à l'observation d'effets non-linéaires. Une modélisation intégrant l'effet thermique et l'effet Kerr a été réalisée. Une confrontation théorie/expérience nous a permis d'estimer la puissance réellement injectée dans le mode ainsi qu'à estimer le volume du mode. / Glass-based whispering gallery mode (WGM) microresonators are easy to produce by melting techniques. However, they suffer from surface contamination which limits their long term quality factor to only about 10E8. In this thesis, we show that an optical gain provided by erbium ions can compensate for residual losses. The optical characterization method is based on frequency-swept “Cavity-Ring-Down-Measurement”. This method can fully describe the linear properties of microcavities such as coupling regime and group delay. In compensation loss regime we demonstrate that it is possible to control the coupling regime of an ultrahigh Q-factor microresonator from undercoupling to spectral selective amplification. Under the selective amplification regime, we obtain an internal Q-factor exceding 10E10. In selective amplification, we experimentally show that it is possible to obtain high amplification up to 33 dB and a high group delay. The microresonators with high Q-factor and high finesse could give rise to a modal coupling which exhibits a splitting of the resonance in the transmission. A characterization of this phenomenon with the cavity ring down method was realized. Moreover, these microresonators, are conducive to the non-linear effect observation. A model incorporating the thermal effect and the Kerr effect has been achieved. Confrontation between theory and experiment allowed us to estimate the real optical power injected into the mode as well as estimating the mode volume.

abstract: This dissertation aims to study and understand relevant issues related to the electronic, spin and valley transport in two-dimensional Dirac systems for different given physical settings. In summary, four key findings are achieved. First, studying persistent currents in confined chaotic Dirac fermion systems with a ring geometry and an applied Aharonov-Bohm flux, unusual whispering-gallery modes with edge-dependent currents and spin polarization are identified. They can survive for highly asymmetric rings that host fully developed classical chaos. By sustaining robust persistent currents, these modes can be utilized to form a robust relativistic quantum two-level system. Second, the quantized topological edge states in confined massive Dirac fermion systems exhibiting a remarkable reverse Stark effect in response to an applied electric field, and an electrically or optically controllable spin switching behavior are uncovered. Third, novel wave scattering and transport in Dirac-like pseudospin-1 systems are reported. (a), for small scatterer size, a surprising revival resonant scattering with a peculiar boundary trapping by forming unusual vortices is uncovered. Intriguingly, it can persist in arbitrarily weak scatterer strength regime, which underlies a superscattering behavior beyond the conventional scenario. (b), for larger size, a perfect caustic phenomenon arises as a manifestation of the super-Klein tunneling effect. (c), in the far-field, an unexpected isotropic transport emerges at low energies. Fourth, a geometric valley Hall effect (gVHE) originated from fractional singular Berry flux is revealed. It is shown that gVHE possesses a nonlinear dependence on the Berry flux with asymmetrical resonance features and can be considerably enhanced by electrically controllable resonant valley skew scattering. With the gVHE, efficient valley filtering can arise and these phenomena are robust against thermal fluctuations and disorder averaging. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2017

Orientador: Newton Cesário Frateschi / Tese (doutorado) - Universidade Estadual de Campinas, Instituto de Física Gleb Wataghin / Made available in DSpace on 2018-08-17T02:03:42Z (GMT). No. of bitstreams: 1 Mialichi_JoseRoberto_D.pdf: 4426656 bytes, checksum: f54944bc3408b22608afdd373e3445dd (MD5) Previous issue date: 2010 / Resumo: Esta tese de doutorado apresenta resultados experimentais do crescimento de pontos quânticos de InAs diretamente sobre InGaAsP de baixa energia de bandgap (?g=1420 nm), cujo desenvolvimento visa a obtenção de um meio ativo com emissão na banda C (1520¿1570 nm) para a fabricação de ressonadores de microdisco. Baseado em resultados de fotoluminescência e microscopia de força atômica, o fenômeno da inter-difusão de elementos na interface InAs/InGaAsP é proposto e calculado, indicando a presença de Gálio e Fósforo na composição dos pontos quânticos. O ganho óptico de pontos quânticos de InAs crescidos sobre InGaAsP é também calculado com base nos resultados obtidos na análise de inter-difusão. Subseqüentemente, a teoria dos modos ressonantes no microdisco, particularmente os modos chamados whispering gallery modes (WGMs), é desenvolvida com o intuito de auxiliar os cálculos de fator de qualidade, fator de confinamento e corrente de limiar. Uma estrutura multicamada (diodo PIN) com região ativa baseada em pontos quânticos do sistema InAs/InGaAsP foi crescida por epitaxia de feixe químico (CBE) para a fabricação de ressonadores de microdisco. A fabricação dos microdiscos é feita por litografia óptica, corrosão por plasma de íons e ataque químico seletivo de InP. Feixe de íons focalizados (FIB) foi usado para substituir o ataque por plasma para diminuir a rugosidade das paredes dos discos. Os ressonadores de microdiscos são caracterizados elétrica e opticamente e os resultados são confrontados com base nos resultados teóricos apresentados ao longo da tese. Com base nos resultados das caracterizações eletro/ópticas dos ressonadores, correções como a inclusão de perdas ópticas da rugosidade da borda e aquecimento local foram acrescidas ao modelo teórico, resultando em boa concordância com os resultados experimentais. Por fim, apresentamos o desenvolvimento de dispositivos híbridos a partir de polímeros orgânicos depositados diretamente sobre microdiscos de InGaAs com o objetivo de integrar meio ativo orgânico com ressonadores inorgânicos para aplicações em optoeletrônica. Estes resultados foram obtidos durante o programa de doutorado com estágio no exterior no Laboratório Nacional de Nanotecnologia (NNL) vinculado à Università del Salento (Lecce/Itália) / Abstract:This doctorate¿s thesis presents the growth of InAs quantum dots directly on high bandgap InGaAsP (?g=1420 nm) barriers to be used as the active region of microdisk resonators with emission in the C-band (1520¿1570 nm). Based on photoluminescence and atomic force microscopy experiments, the occurrence of inter-diffusion on the InAs/InGaAsP interface is calculated, suggesting the presence of Gallium and Phosphorus in the quantum dots (QDs) composition. Based also on the inter-diffusion results, the optical gain of the InAs QDs is calculated. Subsequently, microdisk resonator whispering gallery modes (WGMs) are calculated and employed to predicting the cavity quality and confinement factors, as well as the threshold current. A PIN diode with an active region based on InAs QDs was grown by Chemical Beam Epitaxy (CBE) for the fabrication of current injected microdisk resonators. Microdisk fabrication process is performed using photolithography, reactive ion etching and InP selective wet-etching. Focused ion beam is used to replace the plasma etching in order to reduce the roughness of the disk¿s edge. Microdisks resonators are characterized electrically and optically and the measurements are analyzed based on the theoretical results presented along this thesis. Based on these measurements, optical losses caused by disk¿s edge roughness and local heating are added to our simulation tool, resulting in better agreement with the experimental results. Finally, we present the development of hybrid resonators using organic polymer deposited directly on inorganic microdisks integrating an organic active medium with inorganic resonators for optoelectronic applications. These results were obtained during our work at the National Nanotechnology Laboratory (NNL) and the University of Salento (Lecce/Italy) / Doutorado / Física da Matéria Condensada / Doutor em Física