The development of X-ray Beam Position Monitors (XBPM) used on the Canadian Light Source front ends is described in this thesis, from the design concepts to the practical implementation and commissioning. Surveyed into position to provide a fiducialized point of origin for incoming synchrotron radiation, the primary purpose of the XBPM is to provide a measure of synchrotron beam motion. Currently XBPMs have been installed on three beamlines at the Canadian Light Source, a 2.9 GeV third generation synchrotron radiation source. Two of the XBPMs are comprised of chemical vapour deposition synthetic diamond blades coated with gold and installed on insertion device beamlines, while the third makes use of molybdenum blades for a dipole beamline. By incrementally scanning the blades of the XBPM through the synchrotron beam it is possible to determine the monitors� spatial resolution to beam motion. For the commissioned XBPM a typical spatial resolution of +/- 1 micron of beam motion was achieved; and the thermal power loading capacity has been tested to the 2/5 of maximum value. An independent white beam profiler, comprised of a converter crystal and image acquisition software, was constructed to corroborate the functionality of the XBPM.

The development of X-ray Beam Position Monitors (XBPM) used on the Canadian Light Source front ends is described in this thesis, from the design concepts to the practical implementation and commissioning. Surveyed into position to provide a fiducialized point of origin for incoming synchrotron radiation, the primary purpose of the XBPM is to provide a measure of synchrotron beam motion. Currently XBPMs have been installed on three beamlines at the Canadian Light Source, a 2.9 GeV third generation synchrotron radiation source. Two of the XBPMs are comprised of chemical vapour deposition synthetic diamond blades coated with gold and installed on insertion device beamlines, while the third makes use of molybdenum blades for a dipole beamline. By incrementally scanning the blades of the XBPM through the synchrotron beam it is possible to determine the monitors� spatial resolution to beam motion. For the commissioned XBPM a typical spatial resolution of +/- 1 micron of beam motion was achieved; and the thermal power loading capacity has been tested to the 2/5 of maximum value. An independent white beam profiler, comprised of a converter crystal and image acquisition software, was constructed to corroborate the functionality of the XBPM.

Monte Carlo (MC) methods are widely accepted as the most accurate technique for calculating dose distributions in radiation therapy physics. Simulating the particle transport through the treatment head of a linear accelerator utilizing a MC based code is both a widespread and practical approach to determining detailed clinical beam characteristics such as the energy, angular and spatial distribution of particles which are needed to properly quantify dose. One particular and versatile MC code, the Monte Carlo N-Particle (MCNP) radiation transport code, developed by Los Alamos National Laboratory, has been commonly used to model ionizing radiations for medical physics applications. In this thesis, a Varian 2100C linear accelerator (linac) is modeled and the electron and photon transport through the primary components of the treatment head are simulated using MCNP Version 5_1.3. The 6 MV photon spectra was characterized in a standard 10 x 10 cm2 field and subsequent dose calculations were made in a Virtual Water (VW) phantom. Energy fluence, percent depth dose and beam profile measurements were taken in a modeled VW phantom and the calculated data was compared to measured reference data. In addition, a human phantom was modeled for future dose calculations using the modeled linac. The linac model created can incorporate different beam energies for determining the dose distribution of multiple beam treatments in phantoms for standard 6 MV plans. The adaptability of this MCNP model allows for any number of geometries and sources encountered in medical physics to be computed and applied with relative ease. Future studies can involve adding complex multi-leaf collimator beam shaping and calculating the dose in human phantom models, which would serve as a basis for studies involving MCNP modeling for dose optimization in medical physics applications.

This thesis describes an investigation into the performance of different schemes for generating short x-rays pulses via synchrotron radiation emission. A review is given of the methods that have been previously proposed for this task. From this review, three leading schemes are selected for in-depth investigations, each of which explores the boundary of what is presently achievable in accelerator-based light sources. The first scheme generates short x-ray pulses by operating an electron storage ring in a quasi-isochronous state using a ‘low-alpha’ lattice. High and low emittance lattices are developed, studied through simulation and then implemented on the Diamond storage ring. Beam dynamics and bunch length measurements are presented for a variety of machine conditions, and an assessment is made of the minimum practically achievable bunch length for stable user operation. Radiation pulses of 1 ps r.m.s. are demonstrated using this scheme. The second and third schemes investigate performance limits for a linac-based light source through numerical simulations. The first of these generates ultra-short pulses by passing a highly compressed electron bunch through a long undulator to radiate in the ‘single-spike’ regime. A comparison is made with theoretical predictions for the required electron bunch length to operate in this way, which highlights the need for accurate start-to-end simulations. The final scheme generates ultra-short x-ray pulses through laser manipulation of the electron bunches. The modulated electrons pass through a long undulator with tapered gap, such that only the centre of the modulated portion experiences high free-electron laser (FEL) gain. A method to enhance the FEL output from this scheme using a wavelength filter and grating-compressor is investigated. The sensitivity of the two schemes to jitter sources is determined, and it is demonstrated both schemes are capable of generating GW-level, fully coherent sub-fs soft x-ray pulses. Such pulses would open up the development of time-resolved science to new regimes.

No description available.

No

The curiosity of researchers to find novel characteristics and properties of matter constantly pushes for the development of instrumentation based on X-radiation. I present in this thesis techniques for electron spectroscopy based on developments of X-ray sources both in time structure and energy. One part describes a laser driven High-Harmonic Generation source and the application of an off-plane grating monochromator with additional beamlines and spectrometers. In initial experiments, the source is capable of producing harmonics between the 13th and 23rd of the fundamental laser 800 nm wavelength. The intensity in the 19th harmonic, after monochromatization, was measured to be above 1.2·1010 photons/second with a repetition rate of 5 kHz.  The development of a chopper system synchronized to the bunch clock of an electron storage ring is also presented. The system can be used to adjust the repetition rate of a synchrotron radiation beam to values between 10 and 120 kHz, or for the modulation of continuous sources. The application of the system to both time of flight spectroscopy and laser pump X-ray probe spectroscopy is shown. It was possible to measure triple ionization of Kr and in applied studies the valence band of a laser excited dye-sensitized solar cell interface. The combination of the latter technique with transient absorption measurements is proposed. The organic molecule maleic anhydride (MA) and its binding configuration to the three anatase TiO2 crystals (101), (100), (001) has been investigated by means of Xray Photoelectron Spectroscopy (XPS) and Near Edge X-ray Absorption Fine structure Spectroscopy (NEXAFS). The results provide information on the binding configuration to the 101 crystal. High Kinetic Energy Photoelectron Spectroscopy was used to investigate multilayers of complexes of iron, ruthenium and osmium. The benefit of hard X-rays for ex-situ prepared samples is demonstrated together with the application of resonant valence band measurements to these molecules.