The aim of this thesis was to optimize atomization conditions for selenium hydride in a novel plasma atomizer based on dielectric barrier discharge (DBD) using atomic absorption spectrometry as a detector. Analytical characteristics have been subsequently determined and compared to those reached in a conventional externally heated quartz tube atomizer which was replaced by a sofisticated design of a multiatomizer (MMQTA) in this work. The limit of detection reached in DBD (0,24 ng ml−1 Se) is slightly worse to that observed in MMQTA (0,15 ng ml−1 Se). On the contrary, slightly better resistance towards interferences of Sb, Bi and As was observed in DBD atomizer in comparison with MMQTA. Possibility of selenium preconcentration in a DBD atomizer was studied reaching an overall preconcentration efficiency of 75 ± 5%. The detection limit in a preconcentration mode employing preconcentration period of 300 s has reached 0,012 ng ml−1 Se. Key words: hydride generation atomic absorption spectrometry, dielectric barrier discharge, hydride atomization, hydride trapping, selenium

The aim of this diploma thesis was to optimize in detail atomization conditions for antimony hydride in a novel plasma atomizer based on a dielectric barrier discharge (DBD) with atomic absorption spetrometric detection. Argon was found as the best DBD discharge gas employing a flow rate of 50 ml min-1 Ar while the DBD power was optimized at 30 W. Analytical figures of merit including interference study of As, Se and Bi have been subsequently investigated and the results compared to those found in an externally heated quartz tube atomizer (QTA). The limit of detection reached in DBD (0.15 ng ml-1 Sb) is comparable to that observed in QTA (0.14 ng ml-1 Sb). Finally, possibility of stibane preconcentration in a DBD atomizer was studied. Preconcentration efficiency of 102 ± 6 % was found under optimized conditions.

This thesis describes the optimization of the method for determination of arsenic by the chemical hydride generation coupled with AAS detection in beer samples and raw materials for its preparation. The beer usually contain arsenic at ultratrace level, however, it is necessary to monitor the concentration of this element in the beer. The routinely used method for determination of arsenic is determination by electrothermal atomization. This approach is time consuming, expensive and less sensitive. It has been developer suitable determination of arsenic as a faster and less expensive method. For this method there was optimized the flow rate of argon to 75 ml·min-1, the optimum flow rate for the reagents was 4.0 ml·min-1 and for the sample 5.0 ml·min-1 . 3 % NaBH4 in 0.5 % NaOH was used as the reducing agent for the determination of arsenic, and HCl diluted 1:1 with distilled water was used to acidify the sample. With this parameter LOD was 0.32 μg·l-1 and LOQ 1.05 μg·l-1 . It has been tested the arsenic determination in samples of barley, malt and potable water as beer raw materials. It has been found that the beer matrix is unsuitable for the hydride generation technique due to a stormy reaction in the gas/liquid phase separator. The effect of pretreatment, which is likely to enhance the effect of...

EN The present diploma thesis is focused on optimization methods of titanium and phosphorus concentration for their use in the colloidal solution of TiO2 nanoparticles modified by bisphosphonates. For these analyses was used atomic absorption spectrometry with flame and electrothermal atomization. The characteristics of the two analytes were compared to two different spectrometers. Using the F-AAS technique on the GBC 933 AA spectrometer has been achieved a detection limit of 5,2 mg l-1 for titanium and a detection limit of 163 mg l-1 for the phosphorus. Using the ContrAA 700 spectrometer, F-AAS has been achieved an almost five times lower detection limit of 1,1 mg l-1 for titanium determination. For determination of phosphorus using this spectrometer, was obtained a similar value of 151 mg l-1 , as using the GBC 933 AA spectrometer. The determination of phosphorus by the ET-AAS technique using the ContrAA 700 spectrometer resulted in a detection limit of 1,23 mg l-1 , which is a significant difference compared to the flame system. It has been proved that optimized methods are consistent with the intention, which was confirmed by the analysis of real titanium and phosphorus samples in the colloidal solution of TiO2 nanoparticles modified bisphosphonates.

This thesis deals with the development of a method suitable for determination Te(IV) by UV-photochemical generation of volatile compounds (UV-PVG) in liquid samples. Atomic absorption spectrometry (AAS) and atomic fluorescent spectrometry (AFS) were used as detection methods. The basis of the apparatus for UV-PVG was a mercury lamp wrapped by PTFE capillary. Firstly, the experimental parameters were optimized for both methods. The optimized parameters were the type, concentration, pH and flow rate of the reaction medium, the length of the PTFE reaction coil, carrier gas flow rate (argon), supportive gas flow rate (hydrogen) and atomization temperature. The figures of merit with both detection methods were determined and compared after the method was optimized. Detection limits achieved for these two detection methods were 6,0 µg dm-3 for AFS and 1,50 µg dm-3 for AAS. Performed interference study confirmed a significant effect of many cations of transition metals and hydride forming elements on tellurium determination. The influence of nitric acid in the sample was studied separately. The suitability of the method for tellurium determination was confirmed by using a spiked certified reference material.

The master thesis deals with comparison of atomic fluorescence spektrometry and high resolution continuum source atomic absorption spektrometry for three methods generation of volatile compounds Antimony. In both methods of atomic antimony detection, it compares the most common chemical generation of volatile compounds (hydrides) with two alternative methods - electrochemical and UV - photochemical. The values of performance parameters for the determination of Sb(III) and Sb(V) were determined for all the above combinations. In the case of chemical generation, a surprisingly almost four times higher limit of detection of Sb(III) was found in connection with AFS detection than AAS detection. The final part was devoted to UV - photochemical vapor generation, with AAS detection for Sb(III) reaching limit of detection 4,96 ppb, for Sb(V) 8,63 ppb. Although UV - photochemical generation of volatile antimony compounds did not reach such performance parameters as chemical or electrochemical generation, it was observed that the sensitivity of antimony determination increased greatly when introducing oxygen into the apparatus. The interference study also found a significant positive effect of Fe(II) on the generation efficiency, and this modification partially persisted without further introduction of these...

Previously, selenium was known as an element with negative properties. However, in the last century, the significant positive effects on human health were detected. Currently, the function, behavior and toxicity of selenium are still not well known. The key to understand it is to do speciation analysis. The aim of this diploma thesis is to develop method for determination inorganic (sodium selenite and selenate) and organic (selenourea, selenocystine, selenomethionine) selenium compounds. Parameters of apparatus for electrochemical hydride generation with atomic absorption spectrometry detector were optimized, final conditions were set and optimal conditions for separation process using HPLC were investigated. Calibration dependences for selenium compounds were measured and analytical figures of merit were investigated. In conclusion, a coupled method HPLC- EcHG- QFAAS for determination of individual selenium compounds was proposed, and it was tested on urea samples. Calibrations for these measurements were investigated and analytic characteristics were calculated. Based on these comparisons it can be said that proposed method allows the determination of selected selenium compounds in both aqueous and urea matrices. Subject words: Spectroscopy, analytical chemistry Key words: Atomic absorption...

146f. / Submitted by Ana Hilda Fonseca (anahilda@ufba.br) on 2013-04-03T13:18:57Z No. of bitstreams: 1 Tese Hadla S Ferreira.pdf: 1335067 bytes, checksum: d1c32c23138aa8d7c8145b340260a496 (MD5) / Approved for entry into archive by Ana Hilda Fonseca(anahilda@ufba.br) on 2013-04-23T15:10:36Z (GMT) No. of bitstreams: 1 Tese Hadla S Ferreira.pdf: 1335067 bytes, checksum: d1c32c23138aa8d7c8145b340260a496 (MD5) / Made available in DSpace on 2013-04-23T15:10:36Z (GMT). No. of bitstreams: 1 Tese Hadla S Ferreira.pdf: 1335067 bytes, checksum: d1c32c23138aa8d7c8145b340260a496 (MD5) Previous issue date: 2009 / CAPES / Neste trabalho, foram desenvolvidos métodos para determinação de cádmio e chumbo em amostras ambientais e antimônio e arsênio em amostras de alimentos, utilizando técnicas de espectrometria atômica. A determinação do cádmio e do chumbo foi realizada através de um sistema de injeção em fluxo acoplado a técnica TS FF AAS. Os íons de cádmio (II) e chumbo (II) foram retidos em uma mini-coluna de Amberlite de XAD – 7 impregnada com ditizona. O planejamento Box- Behnken foi empregado para determinação das condições ótimas da etapa de concentração do chumbo e do cádmio. Os limites de detecção foram de 0,012 e 0,34 μg L-1 para cádmio e chumbo, respectivamente. O método foi aplicado em amostras de resíduos de refinaria de petróleo. A exatidão foi confirmada por análise da CRM NIST 1643d. Foi também desenvolvido um método para determinação de espécies tóxicas de arsênio e antimônio em amostras de alho e cogumelos, respectivamente por HG AFS. A determinação das espécies (III) e (V) de arsênio e antimônio foram baseadas na eficiência de geração de hidreto empregando NaBH4, com e sem uma prévia redução com KI, usando equações proporcionais correspondentes para as duas condições de medida. Os analitos foram extraídas com ácido sulfúrico nas condições de 1,0 e 0,5 mol L-1 para arsênio e antimônio, respectivamente. Com o método desenvolvido obteve-se limites de detecção de 0,6, 1,1, 0,84 e 1,4 ng g-1 para Sb(III), Sb(V), As(III) e As(V), respectivamente. A exatidão do método foi confirmada através de testes de adição e recuperação das espécies bem como, um material de referência certificado NIST 1573a. Um método para determinação de arsênio total em vinho também foi desenvolvido. O arsênio foi determinado por FI-HG AAS com um sistema de atomização eletrotérmica. O planejamento Box-Behnken foi utilizado na determinação das condições ótimas para geração de hidreto. Com método proposto obteve um limite de detecção de 0,06 μg L-1 e foi aplicado em 20 amostras de vinhos comercializadas do Brasil. / Salvador

(EN) The presented dissertation thesis summarizes the new results of electrochemical generation of volatile compounds usable in atomic spectral methods. The main aim of this work is to develop and to characterize new types of electrolytic flow-through cells and to examine their possibilities of determination of arsenic, selenium and antimony by using the electrochemical hydride generation technique coupled with atomic absorption spectrometry with a quartz tube atomizer. Individual electrolytic cells were designed and constructed to comply with two important requirements. The cathode chamber of the electrolytic cell should have a minimal volume and a high efficiency of analyte conversion to the volatile hydride. Constructed electrolytic cells are divided into the construction groups and described in the experimental part. Selenium was chosen as the first analyte. The relevant working parameters (such as type, concentration and flow rate of electrolytes, generation current and carrier gas flow rate) were optimized for each newly constructed electrolytic cell. Under the optimal working parameters, the basic characteristics of selenium determination were found out by using electrochemical hydride generation. The electrolytic cells were compared to each other and with the classical electrolytic cell...

O presente trabalho teve como objetivo avaliar, por meio da microscopia eletrônica de varredura (MEV), a capacidade de remoção da smear layer dos terços médio e apical do canal radicular utilizando soluções quelantes e desmineralizantes e, quantificar, por meio da espectrometria de absorção atômica com chama, a concentração de íons cálcio presentes nessas soluções após suas utilizações. Vinte e cinco caninos superiores foram preparados pela técnica Free Tip Preparation com 4 instrumentos acima do inicial e irrigados com hipoclorito de sódio 1% a cada troca de instrumento. Os dentes foram distribuídos aleatoriamente em 4 grupos, conforme protocolo utilizado para a irrigação final: G1 - EDTA 15%, G2 - quitosana 0,2%, G3 - ácido cítrico 10%, G4 - ácido acético 1%. O grupo controle (G5) não recebeu irrigação. Foram utilizados 5 mL de cada solução por 3 minutos. Após percorrer toda extensão do canal radicular a solução extravasada pelo forame foi coletada e encaminhada para análise espectrométrica. Os espécimes foram seccionados longitudinalmente e preparados para análise em MEV. As fotomicrografias obtidas foram avaliadas qualitativamente por três examinadores, que atribuíram escores às imagens, conforme a quantidade de smear layer. Os dados obtidos pela MEV foram analisados estatisticamente por meio do Teste de Kruskal-Wallis e Dunn. Para avaliação da espectrometria utilizou-se Tukey-Kramer (one-Way ANOVA). Os resultados mostraram que o EDTA 15%, quitosana 0,2% e ácido cítrico 10% removeram a smear layer de forma semelhante entre si e estatisticamente diferente (p<0,05) do ácido ácético 1% e controle. Não houve diferença na capacidade de limpeza das soluções quando os terços médio e apical foram comparados. A maior concentração de íons cálcio foi observada no grupo do EDTA 15% e quitosana 0,2%, sem diferença entre ambos. O grupo do ácido acético 1% apresentou as menores concentrações e o ácido cítrico 10%, concentrações intermediárias e diferentes estatísticamente dos dois grupos (p<0,01). Concluiu-se que as soluções de EDTA 15%, quitosana 0,2% e ácido cítrico 10% foram eficientes na remoção da smear layer do terço médio e apical do canal radicular. As soluções de EDTA 15% e quitosana 0,2% promoveram o maior efeito desmineralizante, seguidas pelo ácido cítrico 10% e acido acético 1%. / This study aimed to evaluate, by scanning electron microscopy (SEM), the ability to remove the smear layer from the apical and middle thirds of the root canal using chelators and demineralizing solutions, and quantify, by atomic absorption spectrophotometry flame, the concentration of calcium ions present in these solutions after their use. Twenty-five canines were prepared by Free Tip Preparation Technique with four instruments above the initial and irrigated with 1% sodium hypochlorite in each change of instrument. The teeth were randomly divided into four groups, according to the protocol used for the final irrigation: G1 - EDTA 15%, G2 - 0.2% chitosan, G3 - citric acid 10%, G4 - 1% acetic acid. The control group (G5) did not receive irrigation. We used 5 mL of each solution for 3 minutes. After irrigating the entire length of the root canal through the apical foramen, the solution was collected and sent to spectrometric analysis. The specimens were sectioned longitudinally and prepared for SEM analysis. The photomicrographs were qualitatively evaluated by three observers, who attributed scores to the images, equivalent to the amount of smear layer removal. The data obtained by SEM was statistically analyzed using the Kruskal-Wallis and Dunn tests. To evaluate the spectrometer, the Tukey-Kramer (one-way ANOVA) was used. The results showed that 15% EDTA, 0.2% chitosan and 10% citric acid had a similar smear layer removal with statistically different (p <0.05) when compared to 1% acetic acid and the control group. There was no difference between the solutions cleaning ability when the middle and apical thirds were compared. The highest concentration of calcium ions was observed in 15% EDTA group and 0.2% chitosan, with no statistical difference between them. The 1% acetic acid group had the lowest concentration and the 10% citric acid intermediate concentrations with statistical difference between each other (p <0.01). It can be concluded that the solutions of 15% EDTA, 0.2% chitosan and 10% citric acid were effective in removing the smear layer of the middle and apical thirds of the root canal. 15% EDTA solutions and 0.2% chitosan promoted the greatest effect on the demineralization, followed by 10% citric acid and 1% acetic acid.