Spelling suggestions: "subject:"acidbase accounting"" "subject:"acid:base accounting""
1 |
Inventory, Characterization, and Classification of Minesoils in the Big South Fork National River and Recreation AreaJones, Cassi Savage 01 August 2011 (has links)
The aim of Part One was to discover and investigate the physical and chemical properties of coal minesoils occurring within the Big South Fork National River and Recreation Area (BSF) in order to better understand the nature of these anthropogenic soils. In particular, this information was to identify which, if any, un-reclaimed or recently reclaimed minesoils were actively producing acid mine drainage (AMD) and what properties were inhibiting revegetation. Historical knowledge and maps were used to locate more than 30 un-reclaimed and reclaimed minesoil sites, which were mapped with GPS. Soil profiles were exposed on 18 sites and grab samples taken on another 12. The morphological properties of each full profile were described according to the National Soil Survey Handbook and samples were taken from each horizon. Chemical properties analyzed for include: particle size, acid-base account, pH, exchangeable aluminum, manganese oxides, soil organic carbon, cation-exchange capacity, exchangeable bases, Mehlich I-extractable elements, and total elemental concentrations.
Significant differences in the following properties (averaged) were discovered between the un-reclaimed and reclaimed minesoils: slope, percent rock fragments, dominant lithology, net neutralization potential, pH, extractable aluminum, base saturation, several Mehlich I-extractable nutrients and total elemental concentrations. Hierarchical clustering analysis revealed similar findings and also highlighted instances where reclaimed minesoils were statistically more similar to un-reclaimed minesoils than to other reclaimed minesoils. This indicated that reclamation efforts may not have been completely successful on these sites.
In Part Two, minesoil profiles were classified according to Soil Taxonomy and according to proposed amendments by the International Committee for Anthropogenic Soils (ICOMANTH). The ICOMANTH amendments provided more informative classifications for coal minesoils in the BSF however, shortcomings were noted. Additional recommendations were made and the minesoils were again classified according to these recommendations. Compared to both the Soil Taxonomy and the ICOMANTH classifications, those according to the proposed additional amendments revealed more of the unique properties of the minesoils studied in this project. The results of this study can aid the National Park Service with future land management of the minesoils located within the BSF boundaries and other users of drastically disturbed minesoils.
|
2 |
The impact of gold and coal mine residue on water resources in the Roodepoort and Newcastle areasMorokane, Tebogo Molefe Shadrack 08 May 2012 (has links)
Large quantities of tailings are produced during gold and coal mining activities. These tailings consist of ash dumps, waste rock dumps, in-pit deposits and any other heap, pile or accumulation of residue in the tailings or slimes dams. It has been reported that these tailings can have a significant impact on water quality in the vicinity of gold and coal residues in South Africa. Water quality deterioration in the vicinity of gold and coal mines in the Johannesburg and other areas has been reported. However, little information is available on the potential impact of residues on water quality near Roodepoort and Newcastle where gold and coal, respectively, are mined. The objective of this investigation was therefore to determine the potential impact of gold and coal mine residues on the environment in the vicinity of Roodepoort and Newcastle. Secondary objectives were to identify the metal constituents of gold and coal mine residues, to evaluate and define the current knowledge with regard to the short-term water quality impact of gold and coal residues in terms of concentration of metals leaching from the residues, to assess the potential impact of gold and coal tailings on the water environment within the study areas and to suggest methods to prevent pollution from taking place. Acid Base Accounting (ABA), Toxicity Characteristics Leaching (TCLP), Acid Rain Leaching Procedure (ARLP) and Inductively Plasma Coupled – Mass Spectrometry (IPC-MS) were used as tools to determine the potential impact of gold and coal tailings on the environment. Acid Base Accounting comprises two components that show the potential of the mine residue to produce acid mine drainage, that is, the total sulphur and the net neutralisation potential (NNP). It has been reported that any pyrite mine residue containing more than 0.5% total sulphur may generate acid mine drainage. Mine residues with a net neutralisation potential of less than zero ppt CaCO3 produce acid drainage. The acid base accounting results show that the gold and coal mine residues contain sulphur which has the potential to produce acid mine drainage. Lithium (Li), sodium (Na) magnesium (Mg), aluminium (Al), potassium (K), calcium (Ca), iron (Fe), manganese (Mn) and nickel (Ni) were identified to be present in the gold mine residue. The concentrations of some of the metals that leached from the gold residue according to the TCLP tests were as follows: Al (22 mg/L); Ca (242 mg/L); Fe (29 mg/L); Mn (88 mg/L) and Ni (87 mg/L). The metals that leached from the gold residue according to the ARLP results were as follows: Na (43 mg/L); Al (169 mg/L); Ca (246 mg/L); Fe (771 mg/L); Mn (16 mg/L) and Ni (11 mg/L). Higher concentrations of metals generally leached from the gold residue with the ARLP test than with the TCLP test. The sulphate concentration up-stream of the gold residue was determined at 225 mg/L. This concentration increased to 3 490 mg/L at the decanting point and to 11 577 mg/L downstream of the decanting point. The surface and possibly groundwater are therefore polluted with sulphates. Lithium (Li), sodium (Na), magnesium (Mg), aluminium (Al), potassium (K), calcium (Ca), iron (Fe), manganese (Mn) and nickel (Ni) were identified to be present in the coal mine residue. The concentrations of some of the metals that leached from the coal residue according to the TCLP tests were as follows: Al (3 mg/L); Ca (56 mg/L); Fe (0.21 mg/L); Mn (1 mg/L) and Ni (0.082 mg/L). The metals that leached from the coal residue according to the ARLP test results were as follows: Na (3 mg/L); Al (15 mg/L); Ca (136 mg/L); Fe (0.91 mg/L); Mn (1 mg/L) and Ni (0.07 mg/L). Higher concentrations of metals generally leached from the coal residue with ARLP test than with the TCLP test. The sulphate concentration up-stream of the coal residue was determined at 26 mg/L. This concentration increased to 3 615 mg/L at the decanting point and to 6 509 mg/L downstream of the decanting point. The surface and possibly groundwater are therefore polluted with sulphate. The upstream Na (26 mg/L), Ca (41 mg/L), Fe (0,02 mg/L), Mn (3 mg/L) and Ni (0.065 mg/L) concentrations were low in the case of the gold residues. These concentrations at the decanting point were: Na (289 mg/L); Ca (266 mg/L); Fe (0.2 mg/L); Mn (0.01 mg/L) and Ni (2 mg/L). Fifty metres downstream these concentrations were: Na (140 mg/L); Ca (389 mg/L); Fe (722 mg/L); Mn (395 mg/L) and Ni (15 mg/L). There was a significant increase in the metal concentration from up-stream of the gold residue, to the decanting point and further downstream of the gold residue. The surface and possibly ground water are therefore polluted by the metals leaching from the gold residue. The upstream Na (5 mg/L), Ca (8 mg/L), Fe (0,12 mg/L), Mn (0.015 mg/L) and Ni (0.05 mg/L) concentrations were low in the case of the coal residues. These concentrations at the decanting point were: Na (189 mg/L); Ca (337 mg/L); Fe (68 mg/L); Mn (13 mg/L) and Ni (0.06 mg/L). Fifty metres downstream these concentrations were: Na (65 mg/L); Ca (129 mg/L); Fe (0.48 mg/L); Mn (5 mg/L) and Ni (0.06 mg/L). There was a significant increase in the metal concentration from up-stream of the coal residue, to the decanting point and further downstream of the coal residue. The surface and possibly ground water are therefore polluted by the metals leaching from the coal residue. The gold and coal mine residues are polluting the surface and possibly ground water. Therefore, in order to ameliorate the current status within the Roodepoort and Newcastle catchments, mitigation and management measures such as that the residues should be covered and capped with soil material that would prevent infiltration of the oxygen and rain water into the soil, are recommended. A more comprehensive water quality analysis of the surroundings of the residues is also suggested to be able to better quantify the extent of the problem. Copyright / Dissertation (MSc)--University of Pretoria, 2011. / Chemical Engineering / Unrestricted
|
3 |
Prediction Techniques Of Acid Mine Drainage: A Case Study Of A New Poly- Metallic Mine Development In Erzincan-ilic, TurkeySezer Ozcelik, Ganime Asli 01 February 2007 (has links) (PDF)
Acid Mine Drainage (AMD) is an environmental problem that eventually occurs in
sulfide rich mine sites. In Turkey most of the metal mines are associated with
sulphide minerals and are potential AMD generators. The purpose of this PhD thesis
is to practice universally accepted tools for the prediction of AMD potential for a new
metallic mine development.
This study involves evaluation of geological data, geochemistry, mineralogy, and
acid-base accounting (static tests) data, obtained from the Erzincan-iliç / Ç / ö / pler Gold
Prospect case.
The mineralization in Ç / ö / pler is in sulfide and oxide types. The oxide is a supergene
alteration and porphyry-copper type gold mineralization is classified as an
intermediate sulfidation. The major lithologies observed in the study area are the
regionally un-correlated meta-sedimentary lithologies, Munzur Limestone, and the
Ç / ö / pler Granitoid.Thirty-eight representative samples were tested for AMD prediction purposes.
Sixteen more were included to the sampling scheme for site characterization.
Both acid producing and neutralizing lithologies are present in the mine site.
Similarly it was revealed that the sulphate sulfur content of the samples were
insignificant that any determined total sulfur amount can be directly considered as
the factor for AMD production.
Geochemical data revealed arsenic enrichments up to 10000 ppm in the study area.
Therefore, during the operational stage, in addition to the planning to avoid or
minimize AMD, it is necessary to take precautions against arsenic mobilization
during the design of the AMD neutralization scheme.
Both Kinetic studies and the heavy metal mobilization related to AMD are kept out of
the scope of this investigation. Similarly, management and abatement stages of
AMD are excluded.
|
4 |
Understanding the mechanisms of oxidation of pyritic shale in mining waste and the influence of shale properties on acid mine drainage in the Pilbara BasinSong, Meining January 2010 (has links)
[Truncated abstract] The influence of environmental conditions and properties of pyritic shale in the mining waste from Mt. Whaleback in Western Australia, in particular the inclusions and encapsulation of pyrite on the oxidation of pyritic shale and its subsequent acid mine drainage, was studied by employing an isothermal batch reactor system and QEMSCAN technique. The experimental technique was validated by comparing the experimental results obtained in this study with the literature data. It was found that the presence of water significantly accelerates the rate of shale oxidation. Weathering of the shale samples was found to influence the O2 consumption rate. It was also found that shale properties have a major effect on the oxidation rate and thereby affect the acid generation. Static test methods (Sobek and Lawrence) were employed to test the Neutralisation Potential (NP) of more than 100 actual and composite samples including pyritic shale samples, rock samples, mineral samples, various pyrite-mineral, pyrite-shale, and pseudo-shale blends. The influence of sample properties (bulk elemental composition, and mineralogy), test technique (Sobek and Lawrence) and associated variables (acid strength and volume) on the acid neutralisation potential of the samples was studied. It was found that the Sobek method produced consistently higher NP results under comparable acid conditions to those obtained with the Lawrence method. The theoretical NP values of individual minerals were calculated based on the mineral composition combined with the acid neutralising equations and ideal chemical formula. ... To experimentally model the major mineral phases, 11 minerals were used to produce pyrite-mineral blends and pseudo-shales, whose compositions mimic those of the actual shales studied. Mineral blends were employed to evaluate and contrast their individual acid generation or neutralisation behaviour with binary and higher order interactions. Blends of pyrite with some selected shales were also employed in this study. It was found that interactions can occur between the multiple mineral components which can enhance the rate of acid generation beyond that of the individual behaviour. It was found that the products from the pre-oxidation of shales, the properties and morphology of a sample such as the surface area, encapsulation, the mineralogy and pH all play a significant role in the acid generation and neutralisation rates. However, the absolute rate of acid generation appears to be most sensitive to the components such as Fe3+, which contribute to its reaction mechanisms. This investigation has provided a scientific insight into the acid generation and neutralisation behaviour of pyritic shale in relation to its mineralogy. It was found that the relative instantaneous rates of acid generation and consumption for individual minerals can be significantly different to that of their total potentials for acid generation and neutralisation. The significantly different behaviour of the actual and pseudo shales suggests that at low pH, there may be other mechanisms underlying the net capacity and rates of shales to generate or consume acid than bulk mineralogy. These findings have significant implications to the mining industry operating in reactive grounds.
|
5 |
Sulfide oxidation in some acid sulfate soil materialsWard, Nicholas John Unknown Date (has links)
This thesis examines sulfide oxidation in 4 physically and mineralogically diverse acid sulfate soil (ASS) materials collected from coastal floodplain sites in north-eastern New South Wales. The aim of this study is to gain further understanding of the process of sulfide oxidation in ASS materials, which will allow improved and more effective management strategies to be applied to these materials. The process of sulfide oxidation was examined using laboratory incubation experiments. The oxidation of pyrite was the primary cause of initial acidification of the ASS materials studied. Although the acid volatile sulfur fraction increased in concentration by an order of magnitude over the initial 8 days of incubation, the subsequent oxidation of this fraction did not result in substantial acidification. Sulfate (SO42-) was the dominant sulfur species produced from sulfide oxidation, however, water-soluble SO42- was a poor indicator of the extent of sulfide oxidation. The sulfoxyanion intermediates thiosulfate (S2O32-) and tetrathionate(S4O62-) were only detected in the early stages of incubation, and their relative abundance appeared to be pH dependent. The diminishing presence of these 2 sulfur species as oxidation progressed was indicative that ferric iron (Fe3+) and bacterial catalysis were driving the oxidation processes. The rate of sulfide oxidation, and consequent rate of acidification, was highly dependent on the soil pH and oxygen availability. Accelerated sulfide oxidation was only observed at low pH (i.e. pH < 4.0) when oxygen availability was not limited. The application of sub-optimal amounts of neutralising agents prevented severe soil acidification in the short-term (i.e. up to 2 months), but had little effect on decreasing the rate of sulfide oxidation and acidification in the long-term. Sub-optimal amounts of CaCO3 accelerated sulfide oxidation and acidification of the peaty marcasitic ASS material resulting in elevated soluble Fe and Al concentrations. For some of the ASS materials, sub-optimal applications of seawater-neutralised bauxite refinery residue (SNBRR) also resulted in elevated soluble Al concentrations. The response of partially-oxidised ASS materials to the exclusion of oxygen was variable. The rate of sulfide oxidation, acidification and the production of soluble oxidation products generally decreased markedly when subjected to anoxia. However, especially in highly acidic ASS materials (i.e. pH < 3.5), sulfide oxidation and acidification generally occurred (albeit at much slower rates), most probably due to oxidation by Fe3+. Rapid sulfide re-formation occurred in the peat ASS material that had been oxidised for 63 days, with 0.47% reduced inorganic sulfur (SCR) formed over 60 days of anoxia. Biogeochemical sulfide formation consumes acidity, however, sulfide re-formation was ineffective in reversing acidification under the conditions of this experiment. The peroxide oxidation methods examined were method dependent and substantially underestimated peroxide oxidisable sulfur, sulfidic acidity and net acidity. The precipitation of jarosite during peroxide oxidation was a major factor contributing to the underestimation in these ASS materials. Clay mineral dissolution may contribute towards the underestimation of both sulfidic and net acidity using peroxide oxidation methods. The atmospheric loss of sulfur and acidity was also identified as a possible additional interference. This study has shown that the initial pH of an ASS material is a useful indicator (additional to those already used) of the potential environmental hazard of an ASS material when oxygen is expected to be non-limiting, such as when ASS materials are excavated and stockpiled. The recommended action criteria need to be reassessed as the data indicate that the current criteria are conservative for alkaline and neutral ASS materials, but should be lowered for all acidic ASS materials (i.e. pH < 5.5) to 0.03% sulfide regardless of texture. Alternative strategies are necessary for the management of ASS materials that are subject to oxidation when the addition of optimal rates of neutralising materials cannot be ensured. The treatment of sites containing actual ASS materials by management strategies that rely on oxygen exclusion need to be accompanied by strategies that include either acid neutralisation or containment in order to reduce acid export from the site. The peroxide oxidation methods examined were subject to substantial interferences, and consequently are unable to reliably provide accurate measurements of the reduced inorganic sulfur fraction, sulfidic acidity, and net acidity in ASS materials.
|
6 |
Sulfide oxidation in some acid sulfate soil materialsWard, Nicholas John Unknown Date (has links)
This thesis examines sulfide oxidation in 4 physically and mineralogically diverse acid sulfate soil (ASS) materials collected from coastal floodplain sites in north-eastern New South Wales. The aim of this study is to gain further understanding of the process of sulfide oxidation in ASS materials, which will allow improved and more effective management strategies to be applied to these materials. The process of sulfide oxidation was examined using laboratory incubation experiments. The oxidation of pyrite was the primary cause of initial acidification of the ASS materials studied. Although the acid volatile sulfur fraction increased in concentration by an order of magnitude over the initial 8 days of incubation, the subsequent oxidation of this fraction did not result in substantial acidification. Sulfate (SO42-) was the dominant sulfur species produced from sulfide oxidation, however, water-soluble SO42- was a poor indicator of the extent of sulfide oxidation. The sulfoxyanion intermediates thiosulfate (S2O32-) and tetrathionate(S4O62-) were only detected in the early stages of incubation, and their relative abundance appeared to be pH dependent. The diminishing presence of these 2 sulfur species as oxidation progressed was indicative that ferric iron (Fe3+) and bacterial catalysis were driving the oxidation processes. The rate of sulfide oxidation, and consequent rate of acidification, was highly dependent on the soil pH and oxygen availability. Accelerated sulfide oxidation was only observed at low pH (i.e. pH < 4.0) when oxygen availability was not limited. The application of sub-optimal amounts of neutralising agents prevented severe soil acidification in the short-term (i.e. up to 2 months), but had little effect on decreasing the rate of sulfide oxidation and acidification in the long-term. Sub-optimal amounts of CaCO3 accelerated sulfide oxidation and acidification of the peaty marcasitic ASS material resulting in elevated soluble Fe and Al concentrations. For some of the ASS materials, sub-optimal applications of seawater-neutralised bauxite refinery residue (SNBRR) also resulted in elevated soluble Al concentrations. The response of partially-oxidised ASS materials to the exclusion of oxygen was variable. The rate of sulfide oxidation, acidification and the production of soluble oxidation products generally decreased markedly when subjected to anoxia. However, especially in highly acidic ASS materials (i.e. pH < 3.5), sulfide oxidation and acidification generally occurred (albeit at much slower rates), most probably due to oxidation by Fe3+. Rapid sulfide re-formation occurred in the peat ASS material that had been oxidised for 63 days, with 0.47% reduced inorganic sulfur (SCR) formed over 60 days of anoxia. Biogeochemical sulfide formation consumes acidity, however, sulfide re-formation was ineffective in reversing acidification under the conditions of this experiment. The peroxide oxidation methods examined were method dependent and substantially underestimated peroxide oxidisable sulfur, sulfidic acidity and net acidity. The precipitation of jarosite during peroxide oxidation was a major factor contributing to the underestimation in these ASS materials. Clay mineral dissolution may contribute towards the underestimation of both sulfidic and net acidity using peroxide oxidation methods. The atmospheric loss of sulfur and acidity was also identified as a possible additional interference. This study has shown that the initial pH of an ASS material is a useful indicator (additional to those already used) of the potential environmental hazard of an ASS material when oxygen is expected to be non-limiting, such as when ASS materials are excavated and stockpiled. The recommended action criteria need to be reassessed as the data indicate that the current criteria are conservative for alkaline and neutral ASS materials, but should be lowered for all acidic ASS materials (i.e. pH < 5.5) to 0.03% sulfide regardless of texture. Alternative strategies are necessary for the management of ASS materials that are subject to oxidation when the addition of optimal rates of neutralising materials cannot be ensured. The treatment of sites containing actual ASS materials by management strategies that rely on oxygen exclusion need to be accompanied by strategies that include either acid neutralisation or containment in order to reduce acid export from the site. The peroxide oxidation methods examined were subject to substantial interferences, and consequently are unable to reliably provide accurate measurements of the reduced inorganic sulfur fraction, sulfidic acidity, and net acidity in ASS materials.
|
7 |
Using an Inventory of Unstable Slopes to Prioritize Probabilistic Rockfall Modeling and Acid Base Accounting in Great Smoky Mountains National ParkO'Shea, Thomas A 01 August 2021 (has links)
An inventory of unstable slopes along transportation corridors and performance modeling are important components of geotechnical asset management in Great Smoky Mountains National Park (GRSM). Hazards and risk were assessed for 285 unstable slopes along 151 miles of roadway. A multi-criteria model was created to select fourteen sites for two-dimensional probabilistic rockfall simulations and Acid Base Accounting (ABA) tests. Simulations indicate that rock material would likely enter the roadway at all fourteen sites. ABA test results indicate that influence of significant acid-producing potential is generally confined to slaty rocks of the Anakeesta Formation and graphitic schist of the Wehutty Formation. The research illustrates an approach for prioritizing areas for site-specific investigations towards the goal of improving safety in GRSM. These results can help park officials develop mitigation strategies for rockfall, using strategies such as widening ditches and encapsulating acidic rockfall material.
|
8 |
Geochemical and mineralogical characterization of gold mine tailings for the potential of acid mine drainage in the Sabie - Pilgrims's Rest GoldfieldsLusunzi, Rudzani 21 September 2018 (has links)
MESMEG / Department of Mining and Environmental Geology / This study entails geochemical and mineralogical characterization of gold tailings of Nestor Mine and Glynn’s Lydenberg Mine of the Sabie-Pilgrim’s Rest goldfields. A total of 35 samples were collected and were analysed for chemical composition (XRF and ICP-MS), mineralogical composition (XRD). In addition, acid-base accounting (ABA) techniques had been conducted to predict the potential for acid mine drainage. Seepage from Nestor tailings dump and water samples from the adjacent Sabie River were also collected and analysed by means of inductively coupled plasma mass spectrometry (ICP-MS) and immediate constituent (IC) -analytical techniques. The study revealed that Sabie-pilgrim’s rest goldfield is characterized by both acid generating and non-acid producing tailings, and this is attributed to variations in the mineralogy of source rocks. Gold occurred within the Black Reef Quartzite Formation in the Nestor Mine and within the Malmani Dolomite in the case of Glynn’s Lydenburg Mine. Mineralogy and bulk geochemical analyses performed in this study showed a clear variation in the chemistry of Nestor Mine and Glynn’s Lydenburg Mine tailings. Predominant oxides in Nestor mine tailings samples are SiO2 (ranging from 66.7-91.25 wt. %; followed by Fe2O3 and Al2O3 (in range of 0.82-15.63 wt. %; 3.21-12.50 wt. % respectively); TiO2 (0.18-10.18 wt. %) and CaO (0.005-3.2 wt. %). Also occurring in small amounts is CaO (0.005-3.2 wt. %), K2O (0.51-2.27 wt. %), MgO (0.005-1.46 wt. %), P2O5 (0.029-0.248), Cr2O3 (0.013-0.042 wt. %) and Na2O (0.005-0.05 wt. %). The samples also contain significant concentrations of As (137-1599 ppm), Cu (34-571 ppm), Cr (43-273 ppm), Pb (12-276 ppm), Ni (16-157 ppm), V (29-255 ppm), and Zn 7-485 ppm). In the Glynn’s Lydenburg Mine tailings SiO2 is also the most dominant oxide ranging between 47.95 and 65.89 w%; followed by Al2O3 (4.31 to 16.19 wt. %), Fe2O3 (8.48 to 11.70 wt %), CaO (2.18 to 7.10 wt. %), MgO (2.74 to 4.7 wt. %). Occurring in small amounts is K2O (1.12-1.70 wt. %), MnO (0.089-0.175 wt. %), P2O5 (0.058-0.144 wt. %) and Cr2O3 (0.015-0.027 wt. %). Arsenic (As), is also occurring in significant amounts (807-2502 ppm), followed by Cr (117-238 ppm), Cu (10-104 ppm), V (56-235 ppm), Ni (45-132 ppm), Pb (13-63 ppm) and Zn (90-240 ppm). Nestor Mine tailings associated with Black Reef Formation mineralization have net neutralizing potential (NPR) <2, hence more likely to generate acid; and their acid potential (AP) ranges 1.56 to 140.31 CaCO3/ton and neutralizing potential (NP) range from -57.75 to -0.3 CaCO3/ton. Glynn’s Lydenburg Mine tailings dump which is
vi
associated with dolomite mineralization, however, was not leaching acid. Based on acid-base accounting results, these tailings have more neutralizing potential (ranging between 57.6 and 207.88 CaCO3/ton) than acid potential (ranging between 7.5 and 72.1 CaCO3/ton); and their NPR>2, hence unlikely to produce acid. This is confirmed by paste pH which was in the ranges between 7.35 and 8.17. Tailings eroded from Nestor Mine tailings dump were also found to be characterized by high content of metals and oxides, namely, As, Cu, Ni, Pb, V, and Zn with SiO2, Fe2O3 and TiO2. The tailings were observed eroded into the Sabie River where AMD related precipitate (yellow boy) was also observed, indicating further oxidation downstream. Field observations, onsite analyses of water samples and laboratory results revealed that Nestor Mine tailings storage facility discharges acid mine drainage with considerable amounts of Al, As, Cu, Fe, Mn, Zn and SO4 and very low pH exceeding the limit as per South African water quality standards. High concentrations of these metals have toxicity potential on plants, animals and humans. Upon exposure to oxygen and water, tailings from Nestor Mine are more likely to generate acid mine drainage that can cause detrimental effect to the environment and the surrounding communities. Potential pollutants are Fe, Mn, Al, As, Cr, Cu, Ni and Pb. Tailings from Glynn’s Lydenberg showed no potential for acid mine drainage formation. / NRF
|
Page generated in 0.299 seconds