<p>This thesis addresses assembly issues encountered in optical and fluidic microsystem applications.</p><p>In optics, the first subject concerns the active alignment of components in optical fibersystems. A solution for reducing the cost of optical component assembly while retaining submicron accuracy is to integrate the alignment mechanism onto the optical substrate. A polymer V-shaped actuator is presented that can carry the weight of the large components - on a micromechanical scale - and that can generate movement with six degrees of freedom.</p><p>The second subject in optics is the CMOS-compatible fabrication of monocrystalline silicon micromirror arrays that are intended to serve as CMOS-controlled high-quality spatial light modulators in maskless microlithography systems. A wafer-level assembly method is presented that is based on adhesive wafer bonding whereby a monocrystalline layer is transferred onto a substrate wafer in a CMOS-compatible process without needing bond alignment.</p><p>In fluidics, a hybrid assembly method is introduced that combines two separately micromachined structures to create hotwire anemometers that protrude from a surface with minimum interference with the air flow. The assembled sensor enables one to make accurate time-resolved measurements of the wall shear stress, a quantity that has previously been hard to measure with high time resolution. Also in the field of hotwire anemometers, a method using a hotwire anemometer array is presented for measuring the mass flow, temperature and composition of a gas in a duct.</p><p>In biochemistry, a bio-analysis chip is presented. Single nucleotide polymorphism scoring is performed using dynamic allele-specific hybridization (DASH). Using monolayers of beads, multiplexing based on single-bead analysis is achieved at heating rates more than 20 times faster than conventional DASH provides.</p><p>Space and material e±ciency in packaging are the focus of the other two projects in fluidics. The first introduces an assembly based on layering conductive adhesives for the fabrication of miniature polymer electrolyte membrane fuel cells. The fuel cells made with this low-cost approach perform among the best of their type to date. The second project concerns a new cross-flow microvalve concept. Intended as a step towards the mass production of large-flow I/P converters, the silicon footprint area is minimized by an out-of-plane moving gate and in-plane, half-open pneumatic channels.</p>

This thesis addresses assembly issues encountered in optical and fluidic microsystem applications. In optics, the first subject concerns the active alignment of components in optical fibersystems. A solution for reducing the cost of optical component assembly while retaining submicron accuracy is to integrate the alignment mechanism onto the optical substrate. A polymer V-shaped actuator is presented that can carry the weight of the large components - on a micromechanical scale - and that can generate movement with six degrees of freedom. The second subject in optics is the CMOS-compatible fabrication of monocrystalline silicon micromirror arrays that are intended to serve as CMOS-controlled high-quality spatial light modulators in maskless microlithography systems. A wafer-level assembly method is presented that is based on adhesive wafer bonding whereby a monocrystalline layer is transferred onto a substrate wafer in a CMOS-compatible process without needing bond alignment. In fluidics, a hybrid assembly method is introduced that combines two separately micromachined structures to create hotwire anemometers that protrude from a surface with minimum interference with the air flow. The assembled sensor enables one to make accurate time-resolved measurements of the wall shear stress, a quantity that has previously been hard to measure with high time resolution. Also in the field of hotwire anemometers, a method using a hotwire anemometer array is presented for measuring the mass flow, temperature and composition of a gas in a duct. In biochemistry, a bio-analysis chip is presented. Single nucleotide polymorphism scoring is performed using dynamic allele-specific hybridization (DASH). Using monolayers of beads, multiplexing based on single-bead analysis is achieved at heating rates more than 20 times faster than conventional DASH provides. Space and material e±ciency in packaging are the focus of the other two projects in fluidics. The first introduces an assembly based on layering conductive adhesives for the fabrication of miniature polymer electrolyte membrane fuel cells. The fuel cells made with this low-cost approach perform among the best of their type to date. The second project concerns a new cross-flow microvalve concept. Intended as a step towards the mass production of large-flow I/P converters, the silicon footprint area is minimized by an out-of-plane moving gate and in-plane, half-open pneumatic channels. / QC 20101019