As ligas à base de níquel de alta resistência são utilizadas em uma infinidade de sistemas avançados, onde baixo peso e sistemas de transmissão mecânica de alta densidade de energia são necessários. Componentes, tais como, engrenagens, rolamentos e eixos poderiam ser consideravelmente menor e mais durável se uma grande melhoria em propriedades mecânicas de ligas à base de níquel for alcançada. Um refinamento significativo no tamanho de grão (incluindo nível nano) é um método promissor para a obtenção de melhorias fundamentais nas propriedades mecânicas. O tamanho de grão é conhecido por ter um efeito significativo sobre o comportamento mecânico dos materiais. Um dos métodos mais favoráveis de alcançar refinamento de grão extremo é submetendo os materiais à deformação plástica intensa. As principais variáveis microestruturais nas superligas são a quantidade de precipitados e sua morfologia, o tamanho e a forma do grão e a distribuição de carbonetos (Cr7C3 e Cr23C6) que poderão reduzir propriedades mecânicas da liga. Neste trabalho é apresentada análise por microscopia óptica e eletrônica de transmissão e também os dados de dureza após deformação plástica intensa (tensão de cisalhamento puro) e alguns tratamentos térmicos. / High strength nickel based alloys are used in a multitude of advanced systems where lightweight, high power density mechanical power transmission systems are required. Components such as gears, bearings and shafts could be made significantly smaller and more durable if a major improvement in nickel based alloy mechanical properties could be achieved. A significant refinement in grain size (includes nano level) is thought to be a promising method for achieving fundamental improvements in mechanical properties. Grain size is known to have a significant effect on the mechanical behavior of materials. One of the most favorable methods of achieving extreme grain refinement is by subjecting the materials to severe plastic deformation. The principal microstructural variations in superalloys are the precipitation amount and morphology, grain size and the distribution of carbide precipitation (Cr7C3 and Cr23C6) that could reduce the mechanical properties of the alloys. This work shows optical and transmission electron microscopy analysis and also hardness data after severe plastic deformation (pure shear stress) and some thermal treatments.

As ligas à base de níquel de alta resistência são utilizadas em uma infinidade de sistemas avançados, onde baixo peso e sistemas de transmissão mecânica de alta densidade de energia são necessários. Componentes, tais como, engrenagens, rolamentos e eixos poderiam ser consideravelmente menor e mais durável se uma grande melhoria em propriedades mecânicas de ligas à base de níquel for alcançada. Um refinamento significativo no tamanho de grão (incluindo nível nano) é um método promissor para a obtenção de melhorias fundamentais nas propriedades mecânicas. O tamanho de grão é conhecido por ter um efeito significativo sobre o comportamento mecânico dos materiais. Um dos métodos mais favoráveis de alcançar refinamento de grão extremo é submetendo os materiais à deformação plástica intensa. As principais variáveis microestruturais nas superligas são a quantidade de precipitados e sua morfologia, o tamanho e a forma do grão e a distribuição de carbonetos (Cr7C3 e Cr23C6) que poderão reduzir propriedades mecânicas da liga. Neste trabalho é apresentada análise por microscopia óptica e eletrônica de transmissão e também os dados de dureza após deformação plástica intensa (tensão de cisalhamento puro) e alguns tratamentos térmicos. / High strength nickel based alloys are used in a multitude of advanced systems where lightweight, high power density mechanical power transmission systems are required. Components such as gears, bearings and shafts could be made significantly smaller and more durable if a major improvement in nickel based alloy mechanical properties could be achieved. A significant refinement in grain size (includes nano level) is thought to be a promising method for achieving fundamental improvements in mechanical properties. Grain size is known to have a significant effect on the mechanical behavior of materials. One of the most favorable methods of achieving extreme grain refinement is by subjecting the materials to severe plastic deformation. The principal microstructural variations in superalloys are the precipitation amount and morphology, grain size and the distribution of carbide precipitation (Cr7C3 and Cr23C6) that could reduce the mechanical properties of the alloys. This work shows optical and transmission electron microscopy analysis and also hardness data after severe plastic deformation (pure shear stress) and some thermal treatments.

Um dos principais mecanismos de falha que causam riscos de fratura a reatores de água pressurizada é a corrosão sob tensão de ligas metálicas em água do circuito primário (CSTAP). É causada por uma combinação das tensões de tração, meio ambiente em temperatura e microestruturas metalúrgicas susceptíveis. Ela pode ocorrer, dentre outros locais, nos bocais do mecanismo de acionamento das barras de controle. Essa fratura pode causar acidentes que comprometem a segurança nuclear através do bloqueio das barras de controle e vazamentos de água do circuito primário reduzindo a confiabilidade e a vida útil do reator. O objetivo desta Tese de Doutorado é o estudo de modelos e uma proposta de modelagem para fraturas por corrosão sob tensão em liga 75Ni15Cr9Fe (liga 600), em água de circuito primário de reator de água pressurizada nesses bocais. São superpostos modelos eletroquímicos e de mecânica da fratura e validados com dados obtidos em experimentos e na literatura. Na parte experimental foram utilizados resultados obtidos pelo CDTN no equipamento recém-instalado de ensaio por taxa de deformação lenta. Na literatura está proposto um diagrama que exprime a condição termodinâmica de ocorrerem diversos modos de CSTAP na liga 600: partiu-se de diagramas de potencial x pH (diagramas de Pourbaix), para a liga 600 imersa em água primária à alta temperatura (3000C a 3500C). Sobre ele, determinaram-se os submodos de corrosão, a partir de dados experimentais. Em seguida acrescentou-se uma dimensão adicional ao diagrama, correlacionando uma variável a que se denominou fração de resistência à corrosão sob tensão. No entanto, é possível acrescentar-se outras variáveis que exprimem a cinética de iniciação e/ou crescimento de trinca, provenientes de outras modelagens de CSTAP. A contribuição original deste trabalho se insere nessa fase: partindo-se de uma condição de ensaio de potencial versus pH, foram iniciadas as modelagens de um modelo empírico-comparativo, um semi-empírico-probabilístico, um de tempo de iniciação e um de taxa de deformação, a partir dos ensaios experimentais e superpostas a essa condição. Esses exprimem respectivamente a susceptibilidade à CSTAP, o tempo de falha, e nos dois últimos o tempo de iniciação de falha por corrosão sob tensão. Os resultados foram comparados com os da literatura e se mostraram coerentes. Através desse trabalho, obteve-se uma metodologia de modelagem a partir de dados experimentais. / One of the main failure mechanisms that cause risks to pressurized water reactors is the primary water stress corrosion cracking (PWSCC) occurring in alloys. It can occurs, besides another places, at the control reactor displacement mechanism nozzles. It is caused by the joint effect of tensile stress, temperature, susceptible metallurgical microstructure and environmental conditions of the primary water. These cracks can cause accidents that reduce nuclear safety by blocking the rods displacement and may cause leakage of primary water, reducing the reactors life. In this work it is proposed a study of the existing models and a modeling proposal to primary water stress corrosion cracking in these nozzles in a nickelbased Alloy 600. It is been superposed electrochemical and fracture mechanics models, and validated using experimental and literature data. The experimental data were obtained at CDTN-Brazilian Nuclear Technology Development Center, in a recent installed slow strain rate testing equipment. In the literature it is found a diagram that indicates a thermodynamic condition for the occurrence of some PWSCC submodes in Alloy 600: it was used potential x pH diagrams (Pourbaix diagrams), for Alloy 600 in high temperature primary water (3000C till 3500C). Over it, were located the PWSCC submodes, using experimental data. It was added a third parameter called stress corrosion strength fraction. However, it is possible to superpose to this diagram, other parameters expressing PWSCC initiation or growth kinetics from other models. Here is the proposition of the original contribution of this work: from an original experimental condition of potencial versus pH, it was superposed, an empiric-comparative, a semi-empiric-probabilistic, an initiation time, and a strain rate damage models, to quantify respectively the PWSCC susceptibility, the failure time, and in the two lasts, the initiation time of stress corrosion cracking. It was modeling from our experimental data. The results were compared with the literature and it showed to be coherent. From this work was obtained a modeling methodology from experimental data.

L'Alliage 600 (Ni-15%Cr-10%Fe) est réputé sensible à la Corrosion Sous Contrainte (CSC) en milieu primaire des Réacteurs à Eau Pressurisée (REP). Des études récentes ont montré que la diffusion du chrome était une étape limitante dans la compréhension des mécanismes de CSC. En particulier, le mécanisme d'oxydation interne contrôlé par le taux de défauts local. Dans ce contexte, l'objectif de cette thèse a été de produire des données expérimentales concernant la cinétique de diffusion du chrome en fonction de différents états métallurgiques. Les coefficients de diffusion du chrome ont été mesurés par Spectrométrie de Masse des Ions Secondaires (SIMS) et Spectrométrie à Décharge Luminescente (SDL) en volume et aux joints de grains dans la gamme de température 678 K-1060 K sur des échantillons en nickel pur et d'Alliage 600 monocristallin ou polycristallin. Une partie de cette thèse s'est focalisée sur l'effet de la déformation plastique sur la cinétique de diffusion du chrome pour des échantillons en nickel monocristallin (orienté <101>). Les expériences de diffusion ont été réalisées sur des échantillons non déformés, pré-écrouis à 4% et 20% de déformation plastique et sur des essais in-situ de diffusion en fluage. Les résultats ont montré que les coefficients de diffusion mesurés sur les éprouvettes déformées plastiquement sous charge constante sont supérieurs de six ordres de grandeur à ceux obtenus à l'état non déformé ou pré-écroui. L'accélération de la cinétique de diffusion peut être attribuée à un couplage entre la mobilité des dislocations et la vitesse de déformation plastique. / Alloy 600 (Ni-15%Cr-10%Fe) is known to be susceptible to Stress Corrosion Cracking (SCC) in primary water of Pressurized Water Reactors (PWR). Recent studies have shown that chromium diffusion is a controlling rate step in the comprehension of SCC mechanism. In order to improve the understanding and the modelling of SCC of Alloy 600 in PWR primary medium the aim of this study was to collect data on kinetics diffusion of chromium. Volume and grain boundary diffusion of chromium in pure nickel and Alloy 600 (mono and poly-crystals) has been measured in the temperature range 678 K to 1060 K by using Secondary Ions Mass Spectroscopy (SIMS) and Glow Discharge-Optical Spectrometry (GD-OES) techniques. A particular emphasis has been dedicated to the influence of plastic deformation on chromium diffusion in nickel single crystals (orientated <101>) for different metallurgical states. The experimental tests were carried out in order to compare the chromium diffusion coefficients in free lattice (not deformed), in pre-hardening specimens (4% and 20%) and in dynamic deformed tensile specimens at 773 K. It has been found that chromium diffusivity measured in dynamic plastic deformed creep specimens were six orders of magnitude greater than those obtained in not deformed or pre-hardening specimens. The enhancement of chromium diffusivity can be attributed to the presence of moving dislocations generated during plastic deformation.

De nombreuses études ont prouvé l’affaiblissement de la résistance de l’alliage 600 lors de l’oxydation en milieu primaire des réacteurs à eau pressurisée. Celle-ci induit la rupture localisée du matériau notamment par fissure intergranulaire. La nature ainsi que la structure de l’oxyde se développant à la surface de l’alliage sont parfaitement connues. Cependant, l’influence mécanique de l’oxyde sur l’alliage n’a pas été explorée. L’objectif de cette étude est d’apporter des connaissances nouvelles sur l’impact de l’oxydation sur la réponse mécanique de l’alliage. Un système d’analyse, basé sur l’utilisation de nanoplots comme marqueurs de position, a été développé et mis en œuvre afin de mesurer des déformations engendrées par l’oxydation puis par une traction. Le traitement statistique de ces données a permis de déterminer des évènements rares de haute déformation. Les échantillons utilisés ont été caractérisés par MEB, TEM, XPS et ellipsométrie spectroscopique afin d’en déduire l’épaisseur de la couche d’oxyde interne contraignant l’alliage. De plus, le couplage de l’EBSD avec les nanoplots a permis de déterminer un ensemble de paramètres pouvant servir de critère d’alerte à l’initiation de la fissuration intergranulaire. / The loss of the corrosion resistance of the alloy 600, a nickel base alloy, during the oxidation in pressurized water reactor (PWR) has been demonstrated by many studies. It induces the intergranular stress corrosion cracking (IGSCC). If the chemical composition and the structure of the growing oxide are well-known, the mechanical influence of the oxide on the alloy has not been fully studied, yet. This study aims at bringing new knowledge of the oxidation impact on the mechanical response of the alloy. A new methodology is introduced for determining the local nanodeformation of the alloy 600 induced either by an oxidation or by a tensile loading. This method is based on nanodots disposed at the alloy surface as local markers of position. The statistical analysis of these data allowed to determine rare events of high deformation The samples were characterized locally by SEM, TEM, XPS and spectroscopic ellipsometry to characterize the internal oxide which constrains the alloy. The coupling of the EBSD with the nanodots had enabled to determine a set of parameters, which was used as an alarm criterion for the IGSCC initiation.

In this study, the possibility of using low pressure hydrogenated steam to simulate primary water reactor conditions is examined. The oxides formed on Alloy 600 (WF675) between 350 Celsius and 500 Celsius in low pressure hydrogenated steam (with a ratio of oxygen at the Ni/NiO to oxygen in the system of 20) have been characterised using analytical electron microscopy (AEM) and compared to oxide that formed in a high pressure water in a autoclave at 350 Celsius with 30 cc/kg of hydrogen. Preferential oxidation of grain boundaries and bulk internal oxidation were observed on samples prepared by oxide polishing suspension (OPS). Conversely, samples mechanically ground to 600 grit produced a continuous, protective oxide film which suppressed the preferential and internal oxidation. The surface preparation changed the form of the oxides in both steam and autoclave tests. The preferential oxidation rate has been determined to be K_{oxide} = Aexp{-Q/RT}with A = 2.27×10^(−3) m^(2)s^(−1) and Q = 221 kJ.mol^(−1) (activation energy) for WF675 and A = 5.04 × 10^(−7) m^(2)s^(−1) and Q = 171 kJ.mol^(−1) for 15% cold worked WF675. These values are consistent with the activation energy of primary water stress corrosion cracking (PWSCC) initiation. Bulk oxygen diffusivities were calculated from the internal oxidation after 500 h exposures. At 500 Celsius the oxygen diffusivity was determined to be 1.79×10^(−20) m^(2)s^(−1) for WF675 and 1.21×10^(−20) m^(2)s^(−1) for 15% cold worked WF675, the oxygen diffusivity at 400 Celsius in 15% cold worked WF675 was calculated to be 1.49×10^(−22) m^(2)s^(−1).The Cr-depletion associated with preferential oxidation has been assessed by AEM. The Cr-depletion was asymmetric and it could not be accounted for by local variations in the diffusion rate. Chemically induced grain boundary migration is suggested as a possible explanation. Constant load SCC tests conducted in hydrogenated steam at 400 Celsius have shown a similar trend to the classical dependency of PWSCC as a function of potential. The SCC samples were also prepared with two surface finishes, OPS and 600 grit. In all SCC tests, significantly more cracking was observed on the OPS surface and all failures initiated from this surface.