The structure of Fe[x] - Pd[1-x] (0.85 > x > 0.5) and Fe[x] - Pt[1-x] (0.85 > x > 0.3) thin film alloys co-deposited from the vapour phase over substrate temperatures (T[s]) ranging over 200-700°C have been examined at room temperature, using X-Ray, Microprobe, TEM and SEM techniques. The sequence of phases developed as T[s] is changed have been explained in terms of three factors: a) The structure of the initial phase, which in turn is a function of the T[o] temperature where DeltaG[bcc-fcc]=0 b) Diffusion at the designated temperature, which depends on both T[s] and the rate of deposition. c) Further transformations which occur on cooling through critical ordering or martensite start temperatures. Based on the co-deposited thin film results, a model is proposed which facilitates the determination of alloy phase diagrams. A direct determination of T[o] temperature in certain composition ranges is also possible through vapour deposition techniques. Preliminary calculation of T[o] confirms the experimental results and the role played by magnetic contributions. The combined experimental data for Fe-Pt alloys confirm the earlier assumption of a eutectoid transformation at about 17at% Pt at around 600°C and provides evidence of the efficacy of thin films for the rapid assessment of low temperature equilibria.

In this study, the OMCVD method is demonstrated as a powerful, fast, economic and environmental friendly method to produce a set of PGMelectrocatalysts with different supports, metal content and metal alloys in one step and without the multiple processing stages of impregnation, washing, drying, calcinationsand activation.

<p>In this study, the OMCVD method is demonstrated as a powerful, fast, economic and environmental friendly method to produce a set of PGMelectrocatalysts with different supports, metal content and metal alloys in one step and without the multiple processing stages of impregnation, washing, drying, calcinationsand activation.</p>

<p>In this study, the OMCVD method is demonstrated as a powerful, fast, economic and environmental friendly method to produce a set of PGMelectrocatalysts with different supports, metal content and metal alloys in one step and without the multiple processing stages of impregnation, washing, drying, calcinationsand activation.</p>

In this study, the OMCVD method is demonstrated as a powerful, fast, economic and environmental friendly method to produce a set of PGMelectrocatalysts with different supports, metal content and metal alloys in one step and without the multiple processing stages of impregnation, washing, drying, calcinationsand activation.

Philosophiae Doctor - PhD / In this study, the OMCVD method is demonstrated as a powerful, fast, economic and environmental friendly method to produce a set of PGMelectrocatalysts with different supports, metal content and metal alloys in one step and without the multiple processing stages of impregnation, washing, drying, calcinationsand activation. / South Africa

Neste trabalho avaliou-se a ação positiva da substituição de lantânio por praseodímio e de lantânio por magnésio na performance eletroquímica de eletrodos de ligas de armazenamento de hidrogênio em estado bruto de fusão e com tratamento térmico. O La foi substituído por Mg nas ligas La0,7-xMgxPr0,3Al0,3Mn0,4Co0,5Ni3,8 (x=0,0-0,7) e por Pr nas ligas La0,7-yPryMg0,3Al0,3Mn0,4Co0,5Ni3,8 (y=0,0-0,7). Os parâmetros eletroquímicos analisados foram ativação, capacidade de descarga, retenção da capacidade de descarga, autodescarga e alta taxa de descarga. As ligas apresentaram comportamento passivo em relação à corrosão. As análises por MEV/EDS e por DRX com refinamento por Rietveld revelaram a presença majoritária de fases similares às fases LaNi5, PrNi5, LaMg2Ni9 e PrMg2Ni9 em função das composições das ligas estudadas. Os parâmetros de rede e os volumes da célula unitária das fases diminuíram com a substituição crescente de La por Mg e de La por Pr. As capacidades de descarga máxima decresceram com a substituição crescente de La por Mg e de La por Pr, acompanhando o decréscimo da abundância da fase similar à fase LaNi5 e o aumento da abundância da fase similar à fase LaMg2Ni9. Comparativamente, menores taxas de autodescarga e maior estabilidade cíclica foram observadas para o eletrodo da liga na condição x=0,1, ao passo que o eletrodo da liga na condição y=0,0 apresentou maiores valores de alta taxa de descarga, indicando melhor performance cinética. / In this work, the positive action of the substitution of lanthanum by praseodymium and lanthanum by magnesium in the electrochemical performance of the as-cast and annealed hydrogen storage alloys electrodes had been evaluated. La was replaced by Mg in La0.7-xMgxPr0.3Al0.3Mn0.4Co0.5Ni3.8 (x=0.0-0.7) alloys and by Pr in La0.7-yPryMg0.3Al0.3Mn0.4Co0.5Ni3.8 (y=0.0-0.7) alloys. The electrochemical parameters analyzed were activation, discharge capacity, discharge capacity retention, self-discharge rate and high-rate dischargeability. The alloys showed a passive corrosion behavior. The analyses by SEM/EDS and XRD with Rietveld refinement revealed the majority presence of LaNi5, PrNi5, LaMg2Ni9 and PrMg2Ni9 similar reference phases depending on the compositions of the studied alloys. The lattice parameters and cell volumes of the component phases decreased with increasing substitution of La for Mg and with La for Pr. The maximum discharge capacity decreased with increasing substitution of La for Mg and with La for Pr, following the decrease in the abundance of LaNi5 similar phase and the increase in the abundance of to the LaMg2Ni9 similar phase. Lower self-discharge rates were observed for the alloy electrode when x=0.1, while higher high-rate dischargeability for the alloy electrode when y=0.0 indicated better kinetic performance, comparatively.

Neste trabalho avaliou-se a ação positiva da substituição de lantânio por praseodímio e de lantânio por magnésio na performance eletroquímica de eletrodos de ligas de armazenamento de hidrogênio em estado bruto de fusão e com tratamento térmico. O La foi substituído por Mg nas ligas La0,7-xMgxPr0,3Al0,3Mn0,4Co0,5Ni3,8 (x=0,0-0,7) e por Pr nas ligas La0,7-yPryMg0,3Al0,3Mn0,4Co0,5Ni3,8 (y=0,0-0,7). Os parâmetros eletroquímicos analisados foram ativação, capacidade de descarga, retenção da capacidade de descarga, autodescarga e alta taxa de descarga. As ligas apresentaram comportamento passivo em relação à corrosão. As análises por MEV/EDS e por DRX com refinamento por Rietveld revelaram a presença majoritária de fases similares às fases LaNi5, PrNi5, LaMg2Ni9 e PrMg2Ni9 em função das composições das ligas estudadas. Os parâmetros de rede e os volumes da célula unitária das fases diminuíram com a substituição crescente de La por Mg e de La por Pr. As capacidades de descarga máxima decresceram com a substituição crescente de La por Mg e de La por Pr, acompanhando o decréscimo da abundância da fase similar à fase LaNi5 e o aumento da abundância da fase similar à fase LaMg2Ni9. Comparativamente, menores taxas de autodescarga e maior estabilidade cíclica foram observadas para o eletrodo da liga na condição x=0,1, ao passo que o eletrodo da liga na condição y=0,0 apresentou maiores valores de alta taxa de descarga, indicando melhor performance cinética. / In this work, the positive action of the substitution of lanthanum by praseodymium and lanthanum by magnesium in the electrochemical performance of the as-cast and annealed hydrogen storage alloys electrodes had been evaluated. La was replaced by Mg in La0.7-xMgxPr0.3Al0.3Mn0.4Co0.5Ni3.8 (x=0.0-0.7) alloys and by Pr in La0.7-yPryMg0.3Al0.3Mn0.4Co0.5Ni3.8 (y=0.0-0.7) alloys. The electrochemical parameters analyzed were activation, discharge capacity, discharge capacity retention, self-discharge rate and high-rate dischargeability. The alloys showed a passive corrosion behavior. The analyses by SEM/EDS and XRD with Rietveld refinement revealed the majority presence of LaNi5, PrNi5, LaMg2Ni9 and PrMg2Ni9 similar reference phases depending on the compositions of the studied alloys. The lattice parameters and cell volumes of the component phases decreased with increasing substitution of La for Mg and with La for Pr. The maximum discharge capacity decreased with increasing substitution of La for Mg and with La for Pr, following the decrease in the abundance of LaNi5 similar phase and the increase in the abundance of to the LaMg2Ni9 similar phase. Lower self-discharge rates were observed for the alloy electrode when x=0.1, while higher high-rate dischargeability for the alloy electrode when y=0.0 indicated better kinetic performance, comparatively.