abstract: Limited spectral access motivates technologies that adapt to diminishing resources and increasingly cluttered environments. A joint positioning-communications system is designed and implemented on \acf{COTS} hardware. This system enables simultaneous positioning of, and communications between, nodes in a distributed network of base-stations and unmanned aerial systems (UASs). This technology offers extreme ranging precision ($<$ 5 cm) with minimal bandwidth (10 MHz), a secure communications link to protect against cyberattacks, a small form factor that enables integration into numerous platforms, and minimal resource consumption which supports high-density networks. The positioning and communications tasks are performed simultaneously with a single, co-use waveform, which efficiently utilizes limited resources and supports higher user densities. The positioning task uses a cooperative, point-to-point synchronization protocol to estimate the relative position and orientation of all users within the network. The communications task distributes positioning information between users and secures the positioning task against cyberattacks. This high-performance system is enabled by advanced time-of-arrival estimation techniques and a modern phase-accurate distributed coherence synchronization algorithm. This technology may be installed in ground-stations, ground vehicles, unmanned aerial systems, and airborne vehicles, enabling a highly-mobile, re-configurable network with numerous applications. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2019

abstract: Unmanned aerial systems (UASs) have recently enabled novel applications such as passenger transport and package delivery, but are increasingly vulnerable to cyberattack and therefore difficult to certify. Legacy systems such as GPS provide these capabilities extremely well, but are sensitive to spoofing and hijacking. An alternative intelligent transport system (ITS) was developed that provides highly secure communications, positioning, and timing synchronization services to networks of cooperative RF users, termed Communications and High-Precision Positioning (CHP2) system. This technology was implemented on consumer-off-the-shelf (COTS) hardware and it offers rapid (<100 ms) and precise (<5 cm) positioning capabilities in over-the-air experiments using flexible ground stations and UAS platforms using limited bandwidth (10 MHz). In this study, CHP2 is considered in the context of safety-critical and resource limited transport applications and urban air mobility. The two-way ranging (TWR) protocol over a joint positioning-communications waveform enables distributed coherence and time-of-flight(ToF) estimation. In a multi-antenna setup, the cross-platform ranging on participating nodes in the network translate to precise target location and orientation. In the current form, CHP2 necessitates a cooperative timing exchange at regular intervals. Dynamic resource management supports higher user densities by constantly renegotiating spectral access depending on need and opportunity. With these novel contributions to the field of integrated positioning and communications, CHP2 is a suitable candidate to provide both communications, navigation, and surveillance (CNS) and alternative positioning, navigation, and timing (APNT) services for high density safety-critical transport applications on a variety of vehicular platforms. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2020

abstract: Within the near future, a vast demand for autonomous vehicular techniques can be forecast on both aviation and ground platforms, including autonomous driving, automatic landing, air traffic management. These techniques usually rely on the positioning system and the communication system independently, where it potentially causes spectrum congestion. Inspired by the spectrum sharing technique, Communications and High-Precision Positioning (CHP2) system is invented to provide a high precision position service (precision ~1cm) while performing the communication task simultaneously under the same spectrum. CHP2 system is implemented on the consumer-off-the-shelf (COTS) software-defined radio (SDR) platform with customized hardware. Taking the advantages of the SDR platform, the completed baseband processing chain, time-of-arrival estimation (ToA), time-of-flight estimation (ToF) are mathematically modeled and then implemented onto the system-on-chip (SoC) system. Due to the compact size and cost economy, the CHP2 system can be installed on different aerial or ground platforms enabling a high-mobile and reconfigurable network. In this dissertation report, the implementation procedure of the CHP2 system is discussed in detail. It mainly focuses on the system construction on the Xilinx Ultrascale+ SoC platform. The CHP2 waveform design, ToA solution, and timing exchanging algorithms are also introduced. Finally, several in-lab tests and over-the-air demonstrations are conducted. The demonstration shows the best ranging performance achieves the ~1 cm standard deviation and 10Hz refreshing rate of estimation by using a 10MHz narrow-band signal over 915MHz (US ISM) or 783MHz (EU Licensed) carrier frequency. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2020