Massive MIMO (multiple-input–multiple-output) is a multi-antenna technology for cellular wireless communication, where the base station uses a large number of individually controllable antennas to multiplex users spatially.  This technology can provide a high spectral efficiency.  One of its main challenges is the immense hardware complexity and cost of all the radio chains in the base station.  To make massive MIMO commercially viable, inexpensive, low-complexity hardware with low linearity has to be used, which inherently leads to more signal distortion.  This thesis investigates how the degenerated linearity of some of the main components—power amplifiers, analog-to-digital converters (ADCs) and low-noise amplifiers—affects the performance of the system, with respect to data rate, power consumption and out-of-band radiation. The main results are: Spatial processing can reduce PAR (peak-to-average ratio) of the transmit signals in the downlink to as low as 0B; this, however, does not necessarily reduce power consumption.  In environments with isotropic fading, one-bit ADCs lead to a reduction in effective signal-to-interference-and-noise ratio (SINR) of 4dB in the uplink and four-bit ADCs give a performance close to that of an unquantized system.  An analytical expression for the radiation pattern of the distortion from nonlinear power amplifiers is derived.  It shows how the distortion is beamformed to some extent, that its gain never is greater than that of the desired signal, and that the gain of the distortion is reduced with a higher number of served users and a higher number of channel taps.  Nonlinear low-noise amplifiers give rise to distortion that partly combines coherently and limits the possible SINR.  It is concluded that spatial processing with a large number of antennas reduces the impact of hardware distortion in most cases.  As long as proper attention is paid to the few sources of coherent distortion, the hardware complexity can be reduced in massive MIMO base stations to overcome the hardware challenge and make massive MIMO commercial reality. / Massiv MIMO (eng: multiple-input–multiple-output) är en flerantennsteknologi för cellulär trådlös kommunikation, där basstationen använder ett stort antal individuellt styrbara antenner för att multiplexa användare i rummet.  Denna teknologi kan tillhandahålla en hög spektral effektivitet.  En av dess främsta utmaningar är den enorma hårdvarukomplexiteten och kostnaden hos basstationens alla radiokedjor.  För att massiv MIMO skall bli kommersiellt attraktivt, måste billiga, enkla hårdvarukomponenter med låg linjäritet användas, vilket oundvikligen leder till mer signaldistorsion.  Denna avhandling undersöker hur den försämrade linjäriteten hos några av huvudkomponenterna – effektförstärkare, analog-digital-omvandlare (AD-omvandlare) och lågbrusförstärkare – påverkar systemets prestanda, i termer av datatakt, effektförbrukning och utombandsstrålning.  Huvudresultaten är: Rumslig signalbehandling kan reducera sändsignalernas toppvärde i nerlänken ända ner till 0dB, vilket dock inte nödvändigtvis minskar effektförbrukningen.  I miljöer med isotrop fädning leder enbits-AD-omvandlare till 4dB lägre signal-till-interferens-och-brus-förhållande i upplänken, och fyrabits-AD-omvandlare ger en prestanda nära den ett system utan kvantisering kan uppnå.  Ett analytiskt uttryck för strålningsmönstret för distorsionen från icke-linjära effektförstärkare härleds.  Det visar hur distorsionen till viss del lobformas, att dess förstärkning aldrig är starkare än förstärkningen för den önskade signalen och att distorsionens förstärkning minskar med ett högre antal betjänade användare och ett högre antal kanaltappar.  Icke-linjära lågbrusförstärkare ger upphov distorsion som delvis kombinerar koherent och begränsar det möjliga signal-till-brus-och-interferens-förhållandet.  Slutsatsen är att rumslig signalbehandling med ett stort antal antenner reducerar hårdvarudistorsionens inverkan i de flesta fall.  Så länge som de få källorna till koherent distorsion ges tillbörlig uppmärksamhet, kan hårdvarukomplexiteten minskas i basstationer för massiv MIMO för att övervinna hårdvaruutmaningen och göra massiv MIMO kommersiell verklighet. / 蜂窩無線通訊領域中的大規模多天線技術以多個單獨可控的天線通過空間複用的方式服務多個用戶。如是可以大幅提高頻譜效率。實現此技術的主要難題在於基站所用射頻單元的極大複雜度及成本。爲使大規模多天線技術適用在商業系統中，需使用導致失真的低複雜度低成本的非線性硬件。本文探討若將一些主要部件——功放、模數轉換器、低噪聲放大器——的線性程度降低，系統性能是如何受到影響的，即系統的速率、功耗、帶外泄露等指標。主要的結果爲：空間信號處理可以降低下行信號的峯均比，直至０分貝；然而低峯均比不一定能夠降低功耗。用一比特模數轉換器使上行的信干噪比減少４分貝；用四比特模數轉換器可在各向同性衰落的環境裏實現接近無量化系統的性能。本文推導出非線性功放失真輻射方向的解析公式。該公式展示失真在某種程度上會被波束成形的；具體而言，失真的波束成形增益不大於有效信號的增益，波束成形增益會根據服務用戶數量和信道階數的增長而降低。非線性低噪聲放大器引起的失真，一部分會相干地合併，因此會限制信干噪比的增長。結論爲多天線的空間信號處理可以減少硬件失真的影響。只要適當地處理少數相干失真的來源，大規模多天線基站可以降低硬件複雜度，解決硬件難題，使大規模多天線技術成功地應用在商業系統中成爲現實。

This thesis deals with design and implementation of digital beamformer for 3D radar. The text of this thesis contains derivation of beamforming algorithm and detailed description of it’s implementation on development kit with Cyclone V circuit. At the end of the thesis the beamformer design is verified and it’s further usage is discused.

The aim of the master thesis is to sum up theoretical information about beamforming methods of microphone arrays and to verify their functionality. At the beginning of this work there are simulated different varietes of linear uniform and nonuniform microphone arrays and circular arrays. The results are verificated by a practical measurement in ideal conditions. Then I will focuse on implementation of the DAS(Delay And Sum), SAB(Sub Array Beamforming), CDB(Constant Directivity Beamforming), CDB-CA(CDB-Circular Arrays) beamformer including theoretical and practical verification of the functionality in ideal conditions. At the end of this thesis are all beamforming methods compared with each other at SNR(signal to Noise Ratio) and directivity parameters.

The goal of this master’s thesis is to explore the possibilities of multichannel localization of acoustic signal sources and their following application on a real signal localization and separation, using Beamforming methods. During this thesis two beamforming methods were selected, namely Delay and Sum a Constant Directivity Beamforming - Circular Arrays, and were applicated on real environment signals using two microphone arrays’ geometries ULA (Uniform linear array) and UCA (Uniform Circular array).

In interference-limited wireless networks, interference management techniques are important in order to improve the performance of the systems. Given that spectrum and energy are scarce resources in these networks, techniques that exploit the resources efficiently are desired. We consider a set of base stations operating concurrently in the same spectral band. Each base station is equipped with multiple antennas and transmits data to a single-antenna mobile user. This setting corresponds to the multiple-input single-output (MISO) interference channel (IFC). The receivers are assumed to treat interference signals as noise. Moreover, each transmitter is assumed to know the channels between itself and all receivers perfectly. We study the conflict between the transmitter-receiver pairs (links) using models from game theory and microeconomic theory. These models provide solutions to resource allocation problems which in our case correspond to the joint beamforming design at the transmitters. Our interest lies in solutions that are Pareto optimal. Pareto optimality ensures that it is not further possible to improve the performance of any link without reducing the performance of another link. Strategic games in game theory determine the noncooperative choice of strategies of the players. The outcome of a strategic game is a Nash equilibrium. While the Nash equilibrium in the MISO IFC is generally not efficient, we characterize the necessary null-shaping constraints on the strategy space of each transmitter such that the Nash equilibrium outcome is Pareto optimal. An arbitrator is involved in this setting which dictates the constraints at each transmitter. In contrast to strategic games, coalitional games provide cooperative solutions between the players. We study cooperation between the links via coalitional games without transferable utility. Cooperative beamforming schemes considered are either zero forcing transmission or Wiener filter precoding. We characterize the necessary and sufficient conditions under which the core of the coalitional game with zero forcing transmission is not empty. The core solution concept specifies the strategies with which all players have the incentive to cooperate jointly in a grand coalition. While the core only considers the formation of the grand coalition, coalition formation games study coalition dynamics. We utilize a coalition formation algorithm, called merge-and-split, to determine stable link grouping. Numerical results show that while in the low signal-to-noise ratio (SNR) regime noncooperation between the links is efficient, at high SNR all links benefit in forming a grand coalition. Coalition formation shows its significance in the mid SNR regime where subset link cooperation provides joint performance gains. We use the models of exchange and competitive market from microeconomic theory to determine Pareto optimal equilibria in the two-user MISO IFC. In the exchange model, the links are represented as consumers that can trade goods within themselves. The goods in our setting correspond to the parameters of the beamforming vectors necessary to achieve all Pareto optimal points in the utility region. We utilize the conflict representation of the consumers in the Edgeworth box, a graphical tool that depicts the allocation of the goods for the two consumers, to provide closed-form solution to all Pareto optimal outcomes. The exchange equilibria are a subset of the points on the Pareto boundary at which both consumers achieve larger utility then at the Nash equilibrium. We propose a decentralized bargaining process between the consumers which starts at the Nash equilibrium and ends at an outcome arbitrarily close to an exchange equilibrium. The design of the bargaining process relies on a systematic study of the allocations in the Edgeworth box. In comparison to the exchange model, a competitive market additionally defines prices for the goods. The equilibrium in this economy is called Walrasian and corresponds to the prices that equate the demand to the supply of goods. We calculate the unique Walrasian equilibrium and propose a coordination process that is realized by the arbitrator which distributes the Walrasian prices to the consumers. The consumers then calculate in a decentralized manner their optimal demand corresponding to beamforming vectors that achieve the Walrasian equilibrium. This outcome is Pareto optimal and lies in the set of exchange equilibria. In this thesis, based on the game theoretic and microeconomic models, efficient beamforming strategies are proposed that jointly improve the performance of the systems. The gained results are applicable in interference-limited wireless networks requiring either coordination from the arbitrator or direct cooperation between the transmitters.

No description available.

Providing a broadband access anytime and anywhere is one of the visions of the future 5G network. However, deploying a reliable network connection in remote/rural areas has been a challenging task because of its wide area that needed to be covered and a low density of user compared to urban area. Different geography and traffic condition may need different system solution. In this thesis, we analyze several solutions to providing a broadband access network in practical remote and rural area in Banten, Indonesia: Leuwidamar (remote) and Panimbang (rural). Two approaches are discussed, first one is fulfilling futuristic traffic demand by having LTE System, and the second one is by having 5G System. We included three key technology components in a 5G network: occupying wide bandwidth in high frequency, applying UE-Specific Beamforming, and implementing Carrier Aggregation (CA) scheme. We also account a rain attenuation when deploying a network in high operating frequency, since Indonesia has a high rain rate thus it is important to be considered. We compared five cases of solution: Case 1 is Single Carrier (SC) LTE 1.8 GHz system; Case 2 is Carrier Aggregation (CA) LTE 1.8 GHz + 2.6 GHz; Case 3 is SC 5G 15GHz; Case 4 is SC 5G 28 GHz; Case 5 is CA LTE 1.8 GHz + 5G 15 GHz. Basedon the evaluation, in Leuwidamar scenario, Case 5 gives us the least number of BS needed in order to meet the futuristic requirement with only 1.6 x densification from the current network. In Panimbang, the least number of BS neededis offered by two cases, Case 3 and Case 5 without any additional BS needed(1x densification). However, the solution with the lowest energy consumption for both area is Case 3. This is due to the fact that the carrier aggregation scenario needs additional power to generate the second system. Furthermore, if we introduce cell DTX ability in the 5G network, the Case 3 can give us impressive amount of energy saving, with 97% saving for Leuwidamar and 94% saving for Panimbang, compared to Case 1 solution without any DTX Capability. / Att tillhandahålla bredbandsanslutning när som helst och var som helst är en av visionerna för det framtida 5G-nätverket. Att använda en tillförlitlig nätverksanslutning i avlägsna- eller landsbygdsområden har dock varit en utmanande uppgift på grund av det breda området som måste täckas och den låga täthetenav användare jämfört med stadsområden. Olika geografiska förhållanden och trafikförhållanden kan behöva olika systemlösningar. I denna avhandling analyserarvi flera lösningar för att tillhandahåller ett bredbandsnätverk i verkligt avlägset eller landsbygdsområde i Banten, Indonesien: Leuwidamar (avlägset) och Panimbang (landsbygd). Två strategier diskuteras, den första uppfyller framtida trafikbehov genom att ha LTE-system och den andra är genom att ha5G System. Vi inkluderade tre viktiga teknikkomponenter i 5G-nätverk: bredbandbredd och hög frekvens, tillämpar UE-specifik strålformning och implementeringav carrier aggregation (CA). Vi redovisar också en dämpning av regn när nätverket används i hög bärvågsfrekvens, eftersom Indonesien har en hög regnhastighet och det är viktigt att överväga. Vi jämförde fem fall av lösning:Fall 1 är Single Carrier (SC) eller Enkelbärare LTE 1.8 GHz system; Fall 2 är bärareaggregation (CA) LTE 1,8 GHz + 2.6 GHz; Fall 3 är SC 5G 15 GHz;Fall 4 är SC 5G 28 GHz; Fall 5 är CA LTE 1.8 GHz + 5G 15 GHz. Baserat på utvärderingen, i Leuwidamar-scenariot,ger Fall 5 oss det minsta antalet BSsom behövs för att möta det futuristiska kravet med endast 1.6 gångers förtätning från nuvarande nätverk. I Panimbang erbjuds det minsta antalet BS somkrävs i två fall, fall 3 och fall 5 utan ytterligare BS behövs (1 gångers förtätning). Lösningen med den lägsta energiförbrukningen för båda områdena är fall 3. Detta beror på att bäraraggregations scenariot behöver ytterligare effekt för att generera det andra systemet. Om vi introducerar cell DTX-funktionen i 5G-nätverket kan Fall 3 ge oss en imponerande energibesparing, med 97% minskning för Leuwidamar och 94% för Panimbang jämfört med Fall 1-lösning utan DTX-funktion.

Unmanned aerial vehicles (UAVs) are emerging as enablers for supporting many applications and services, such as precision agriculture, search and rescue, temporary network deployment, coverage extension, and security. UAVs are being considered for integration into emerging wireless networks as aerial users, aerial relays (ARs), or aerial base stations (ABSs). This dissertation proposes employing UAVs to contribute to physical layer techniques that enhance the security performance of advanced wireless networks and services in terms of availability, resilience, and confidentiality. The focus is on securing terrestrial cellular communications against eavesdropping with a cellular-connected UAV that is dispatched as an AR or ABS. The research develops mathematical tools and applies machine learning algorithms to jointly optimize UAV trajectory and advanced communication parameters for improving the secrecy rate of wireless links, covering various communication scenarios: static and mobile users, single and multiple users, and single and multiple eavesdroppers with and without knowledge of the location of attackers and their channel state information. The analysis is based on established air-to-ground and air-to-air channel models for single and multiple antenna systems while taking into consideration the limited on-board energy resources of cellular-connected UAVs. Simulation results show fast algorithm convergence and significant improvements in terms of channel secrecy capacity that can be achieved when UAVs assist terrestrial cellular networks as proposed here over state-of-the-art solutions. In addition, numerical results demonstrate that the proposed methods scale well with the number of users to be served and with different eavesdropping distributions. The presented solutions are wireless protocol agnostic, can complement traditional security principles, and can be extended to address other communication security and performance needs.

Phased array feeds (PAFs) are a promising new technology for astronomical radio telescopes. While PAFs have been used in other fields, the demanding sensitivity and calibration requirements in astronomy present unique new challenges. This dissertation presents some of the first astronomical PAF results demonstrating the lowest noise temperature and highest sensitivity at the time (66 Kelvin and 3.3 m^2/K, respectively), obtained using a narrowband (425 kHz bandwidth) prototype array of 19 linear co-polarized L-band dipoles mounted at the focus of the Green Bank 20 Meter Telescope at the National Radio Astronomy Observatory (NRAO) in Green Bank, West Virginia. Results include spectral line detection of hydroxyl (OH) sources W49N and W3OH, and some of the first radio camera images made using a PAF, including an image of the Cygnus X region. A novel array Y-factor technique for measuring the isotropic noise response of the array is shown along with experimental measurements for this PAF. Statistically optimal beamformers (Maximum SNR and MVDR) are used throughout the work. Radio-frequency interference (RFI) mitigation is demonstrated experimentally using spatial cancelation with the PAF. Improved RFI mitigation is achieved in the challenging cases of low interference-to-noise ratio (INR) and moving interference by combining subspace projection (SP) beamforming with a polynomial model to track a rank 1 subspace. Limiting factors in SP are investigated including sample estimation error, subspace smearing, noise bias, and spectral scooping; each of these factors is overcome with the polynomial model and prewhitening. Numerical optimization leads to the polynomial subspace projection (PSP) method, and least-squares fitting to the series of dominant eigenvectors over a series of short term integrations (STIs) leads to the eigenvector polynomial subspace projection (EPSP) method. Expressions for the gradient, Hessian, and Jacobian are given for use in numerical optimization. Results are given for simulated and experimental data, demonstrating deeper beampattern nulls by 6 to 30dB. To increase the system bandwidth toward the hundreds of MHz bandwidth required by astronomers for a fully science-ready instrument, an FPGA digital backend is introduced using a 64-input analog-to-digital converter running at 50 Msamp/sec and the ROACH processing board developed at the University of California, Berkeley. International efforts to develop digital back ends for large antenna arrays are considered, and a road map is proposed for development of a hardware correlator/beamformer at BYU using three ROACH boards communicating over 10 gigabit Ethernet.

Among the research topics needing to be addressed to further the development of phased array feeds (PAFs) for radio astronomical use are challenges associated with calibration, beamforming, and imaging for single dish observations. This dissertation addresses these concerns by providing analysis and solutions that provide a clearer understanding of the effort required to implement PAFs for complex scientific research. It is shown that calibration data are relatively stable over a period of five days and may still be adequate after 70 days. A calibration update system is presented with the potential to refresh old calibrators. Direction-dependent variations have a much greater affect on calibration stability than temporal variations. There is an inherent trade-off in beamformer design between achieving high sensitivity and maintaining beam pattern stability. A hybrid beamformer design is introduced which uses a numerical optimizer to balance the trade-off between these two conflicting goals to provide the greatest sensitivity for a desired amount of pattern control. Relative beam variations that occur when electronically steering beams in the field of view must be reduced in order for a PAF to be useful for source detection and imaging. A dual constraint beamformer is presented that has the ability to simultaneously achieve a uniform main beam gain and specified noise response across all beams. This alone does not reduce the beam variations but it eliminates one aspect of the problem. Incorporating spillover noise control through the use of rim calibrators is shown to reduce the variations between beams. Combining the dual constraint and rim constraint beamformers offers a beamforming option that provides both of these benefits.