No description available.

No description available.

The purpose of this project is to quantify the effects of increasing spinal ligament fidelity on the mechanics of the human lumbar spine using finite element analysis (FEA). In support of this goal, a material characterization study was completed to provide anisotropic, nonlinear material parameters for the human anterior longitudinal ligament. (ALL). Cadaveric samples of the human ALL were tested using a punch test technique. Multi- axial force-deformation data were gathered and fit to a commonly used transversely isotropic material model using an FEA system identification routine. The resulting material parameters produced a curve that correlated well with the experimental curve (R2≥0.98). Recently published material data on several major spinal ligaments have been incorporated into an existing finite element model of the human lumbar spine. This data includes the results from the above mentioned material characterization, similar material characterizations of the supraspinous (SSL) and interspinous (ISL) ligaments, localized material properties of the SSL and pre-strain data for the ISL, SSL and ALL. These results have been incorporated both separately and compositely into the finite element model and each configuration has been simulated in spinal flexion, extension, axial rotation and lateral bending. Results suggest that the effects of increased ligament model fidelity on bone strain energy were moderate and the effects on disc pressure were slight, and do not justify a change in modeling strategy for most clinical applications. There were significant effects on the ligament stresses of the ligaments that were directly modified, suggesting that these phenomenon should be included in FE models where ligament stresses are the desired metric.

Bone is a largely bipartite viscoelastic composite. Its mechanical behavior is determined by strain rate and the relative proportions of its principal constituent elements, hydroxyapatite and collagen, but is also largely dictated by their geometry and topology. Collagen fibrils include many segments of tropocollagen in staggered, parallel sequences. The physical staggering of this tropocollagen allows for gaps known as hole-zones, which serve as nucleation points for apatite mineral. The distance between adjacent repeat units of tropocollagen is known as D-Spacing and can be measured by Atomic Force Microscopy (AFM). This D-Spacing can vary in length slightly within a bundle, but by an additional order of magnitude within the same specimen, and can significantly alter the proportion of hydroxyapatite. Previous researchers have built and refined a Finite Element Analysis “Complex Model” to capture the consequences of adjusting D-Spacing and the viscoelastic parameters. This will ultimately serve to elucidate and perhaps predict the mechanical consequences of biological events that alter these parameters. This study aims to further refine the model’s precision by accounting for crosslinking between fibrils, the presence of which serves to add mechanical strength. This study also looks to refine the currently used rheological models by way of frequency dependent parameters in the hopes of improving model accuracy over a wider frequency range. Hormonal factors such as estrogen can significantly determine the composition of bone. Menopause marks a significant reduction in circulating estrogen and has been shown to factor heavily in the development of conditions like osteoporosis. Because sheep feature a hormonal cycle and skeletal structure similar to humans, three of six mature Columbia-Rambouillet ewes were randomly selected to undergo an ovariectomy, the remainder serving as sham-operated controls. Twelve months later twenty-five beam samples were harvested from their radius bones for mechanical analysis and other testing, including atomic force microscopy (AFM) and dynamic mechanical analysis (DMA). The data gleaned from these tests provide an experimental basis of comparison with The Complex Model. A 2-D Finite Element Analysis model in Abaqus was first created by Miguel Mendoza, which enforced viscoelasticity and a realistic proportion and placement of hydroxyapatite and collagen. The viscoelasticity was modeled using a Standard Linear Solid involving springs and a dashpot element. Crosslinks of varying number and location were arranged within the former model configuration as node to surface tie-constraints to explore the treatment of the FEA Model as a more realistic assembly of parts. Frequencies utilized for this model included 1, 3, 9 and 12 Hz. This approach is referred to in this research as the Intermolecular Forces (IMF) Scheme. The model was subsequently refined by Christopher Ha and Austin Cummings. The model was characterized by 2x100 unit half-cells, the lengths of which were randomly generated by a Python script. This script ingested the mean and standard deviation D-Spacing length to generate a model geometrically similar to a real specimen bearing those dimensions. A frequency dependent value for the dashpot element in the rheological model used for tropocollagen was developed using this latter FEA model, named the Complex Model. Dashpot values explored for this variable dashpot included 0.0125, 0.125, 0.3125, 0.45, 0.5875, 0.725, 0.8625 and 1.25 GPa-s, some values chosen for their high performance in past studies and others to further narrow the search for the best performing dashpot. All dashpot values were investigated over the previously stated frequencies in addition to 2, 5, 7 and 12 Hz. The best fit dashpot values were plotted against the frequencies in which they best performed and a polynomial trend line was fitted to establish an equation, and that equation was used to modify an existing user material subroutine for tropocollagen to provide an automatic frequency dependent dashpot value to Abaqus. This approach is referred to in this research as the Variable Dashpot (VD) Scheme. Results for the IMF scheme generally performed poorly, with the fully tie-constrained model performing best with 0.77 and 0.024 for R2 and RMSE respectively. Of the randomized crosslink models, that with the lowest number (N=20) of randomly placed non-enzymatic crosslinks performed best with 0.81 and 0.051 for R2 and RMSE respectively. Increasing the number of randomized crosslinks reduced model fit, and the remaining three variants exhibited mean R2 and RMSE values of 0.66-0.67 and 0.052 respectively. For the VD scheme, models running custom modified variable dashpot UMATs yielded R2 and RMSE values of 0.87 and 0.012 for C2207, and 0.89 and 0.008 for C1809. This is a notable fit considering all other material property parameters are held constant throughout each frequency. In the rheological model, this research also found a striking difference between the frequency dependent viscous element values that made each model perform best. This indicates that differences in D-Spacing standard deviations between OVX and control may be associated with distinct strain-rate dependent mechanical responses.

Atherosclerosis causes hundreds of thousands of deaths in the US alone every year. Fibrous cap rupture is one of the leading causes of these fatalities. Thin cap atheromas are commonly regarded as vulnerable plaque, however the effect of calcium upon a thin fibrous cap with lipid pool is poorly understood. Some studies have shown that calcium adds to stability of the lesion, while others have proven otherwise. An article by Li et al. 2007 suggests location is the key factor. By varying the percentage of calcium and lipid within a defined region, the stress on the cap was estimated using an idealized finite element arterial model. Also the thickness of the fibrous cap was varied to determine whether the stress was solely a function of lipid percentage or a combination. Plaque, arterial wall, lipid, and calcium were modeled using linear elastic, isotropic, and incompressible material properties. The first test varied the thin cap thickness from 65 to 500 microns and tested the calcified lipid model at varying lipid/calcium percentages. The lipid/Calcium pool increased/decreased 10% each test. As the cap thickness becomes thinner than 100 microns, the stress level increases rapidly. The second test compared a model with lipid pool and calcium behind the lipid with a thin cap of 65 microns to a model with lipid pool of the same size and thin cap of 65 microns but only fibrous tissue surrounding (no calcium). The lipid pool increased from 10 to 90% lipid. The result of this test found that at higher lipid percentages, the calcium increased the stress on the cap. By understanding the material properties of plaque and the structure of the lesion, future developments may be able to evaluate rupture risk. This idealized study illustrates the ability of computation models to provide insight into clinical situations.

Finite element models for the analysis of solid slabs and precast hollow core slabs composite girders are presented. For both models, 8-node three-dimensional solid elements are used in the analysis. The material non-linearity of all components of the composite girders is taken into consideration. The non-linear load-slip characteristics of the headed shear stud connectors are included in the models. The models predict load – deflection behaviour and stress distribution along the length of the beam. Good agreement is obtained between the models and results previously published.

Quick, efficient, and reliable methods for in-service inspection of rails to ensure the safety of transportation is an open challenge in the railroad industry. It is well known that fatigue cracks are the leading cause of derailments. Furthermore, new high-speed and heavy-load trains have seen increased use, leading to an increase in the loads and number of cycles experienced by a given section of track. Additionally, most methods for inspecting rails require that sections of the track be shut down for inspection. As a result, much industry attention has been paid to the development of nondestructive methods for inspecting whole sections of the track, although a significant gap in inspection needs and capabilities exists, especially with the inspection of rail base. This studied the feasibility of applying Line Scan Thermography (LST) toward detecting defects in the rail base using Finite Element Analysis (FEA) validated by analytical solutions and experiments and simulated the LST inspection in multiple models at speeds up to 40 mph. In the simulations, subsurface fabricated defects were considered to correlate the necessary thermal contrast, amount of energy, and scan speed. The digital twins, when compared to experimental results, showed the same trend. The rail base section model was simulated with 6000 W of heat, and scanning speeds varying from 0.3 mph up to 40 mph with a 150 mm distance showed an exponential decrease in the thermal contrast. However, when the heat power and camera location are changed proportionally to the speed increase, the thermal contrast remains within a change of 1% and 16% for the detectable reflectors. Moreover, the technique was considered feasible if the previous relationship was respected. Further studies regarding this application account for a deeper investigation of this scanning speed and energy relation, developing a Computational Fluid Dynamics model of this problem, and testing samples with surface defects.

yes / The problem of parametric surface meshing for the purpose of design optimisation using finite element analysis is considered. Here the surface mesh is generated as a solution of a suitably posed boundary value problem implemented on a 2D parameter space. A robust meshing scheme is presented where an initial mesh is manipulated, with the aid of the 2D parameter space, so as to obtain a suitable surface triangulation. This meshing scheme can then be used to create suitable finite element meshes with which accurate design optimisations can be carried out.

Indiana University-Purdue University Indianapolis (IUPUI) / In this project, a chassis concept has been developed for a small electric vehicle ’minibus’. The vehicle is intended to be used as a transport between agricultural locations in Ethiopia to cities where the products can be sold. The objective is to develop a chassis that can house several different modular structures for the purposes of transporting refrigerated goods, a mobile power grid, or people. Literature studies have been conducted on current electric vehicle markets, battery markets, chassis materials, and optimal cross-sections. The battery housings have also been analyzed from an environmental perspective to account for conditions in Ethiopia. Based on this, it was found that a four-wheeled ’minibus’ design including space for approximately fourteen custom batteries is optimal. It is essential to keep in mind that this project has been carried out both on a conceptual level within the framework of a degree project as well as a production project for use in Ethiopian rural areas. This master thesis project aims to provide a solid benchmark for further development and research within the subject.

This thesis discusses the analysis of surface cracked configurations in order to develop a fracture prediction criterion suitable for ductile materials. A similar criteria has been successfully developed for brittle materials. However, the criteria has not been applied to ductile materials. Finite element analysis results are presented as well as laboratory test data. The validity of the proposed criterion is addressed and future work is proposed.