This thesis deals with the near-field of confluent jets, which can be of interest in many engineering applications such as design of a ventilation supply device. The physical effect of interaction between multiple closely spaced jets is studied using experimental and numerical methods. The primary aim of this study is to explore a better understanding of flow and turbulence behavior of multiple interacting jets. The main goal is to gain an insight into the confluence of jets occurring in the near-field of multiple interacting jets. The array of multiple interacting jets is studied when they are placed on a flat and a curved surface. To obtain the boundary conditions at the nozzle exits of the confluent jets on a curved surface, the results of numerical prediction of a cylindrical air supply device using two turbulence models (realizable 𝑘 − 𝜖 and Reynolds stress model) are validated with hot-wire anemometry (HWA) near different nozzles discharge in the array. A single round jet is then studied to find the appropriate turbulence models for the prediction of the three-dimensional flow field and to gain an understanding of the effect of the boundary conditions predicted at the nozzle inlet. In comparison with HWA measurements, the turbulence models with low Reynolds correction (𝑘 − 𝜖 and shear stress transport [SST] 𝑘 − 𝜔) give reasonable flow predictions for the single round jet with the prescribed inlet boundary conditions, while the transition models (𝑘 − 𝑘l − 𝜔𝜔 and transition SST 𝑘 − 𝜔) are unable to predict the flow in the turbulent region. The results of numerical prediction (low Reynolds SST 𝑘 − 𝜔 model) using the prescribed inlet boundary conditions agree well with the HWA measurement in the nearfield of confluent jets on a curved surface, except in the merging region. Instantaneous velocity measurements are performed by laser Doppler anemometry (LDA) and particle image velocimetry (PIV) in two different configurations, a single row of parallel coplanar jets and an inline array of jets on a flat surface. The results of LDA and PIV are compared, which exhibit good agreement except near the nozzle exits. The streamwise velocity profile of the jets in the initial region shows a saddle back shape with attenuated turbulence in the core region and two off-centered narrow peaks. When confluent jets issue from an array of closely spaced nozzles, they may converge, merge, and combine after a certain distance downstream of the nozzle edge. The deflection plays a salient role for the multiple interacting jets (except in the single row configuration), where all the jets are converged towards the center of the array. The jet position, such as central, side and corner jets, significantly influences the development features of the jets, such as velocity decay and lateral displacement. The flow field of confluent jets exhibits asymmetrical distributions of Reynolds stresses around the axis of the jets and highly anisotropic turbulence. The velocity decays slower in the combined regio  of confluent jets than a single jet. Using the response surface methodology, the correlations between characteristic points (merging and combined points) and the statistically significant terms of the three design factors (inlet velocity, spacing between the nozzles and diameter of the nozzles) are determined for the single row of coplanar parallel jets. The computational parametric study of the single row configuration shows that spacing has the greatest impact on the near-field characteristics.

<p>The compressible turbulent boundary layer developing over atwo-dimensional bump which leads to a supersonic pocket with aterminating shock wave has been studied. The measurements havebeen made with hot-wire anemometry and Particle ImageVelocimetry (PIV).</p><p>A method to calibrate hot-wire probes in compressible ow hasbeen developed which take into account not only the ow velocitybut also the inuence of the Mach number, stagnation temperatureand uid density. The calibration unit consists of a small jetow facility, where the temperature can be varied. The hot wiresare calibrated in the potential core of the free jet. The jetemanates in a container where the static pressure can becontrolled, and thereby the gas density. The calibration methodwas verfied in the at plate zero pressure gradient turbulentboundary layer in front of the bump at three different Machnumbers, namely 0.3, 0.5 and 0.7. The profiles were alsomeasured at different static pressures in order to see theinuence of varying density. Good agreement between the profilesmeasured at different pressures, as well as with the standardlogarithmic profile was obtained.</p><p>The PIV measurements of the boundary layer ow in front ofthe 2D bump showed good agreement with the velocity profilesmeasured with hotwire anemometry. The shock wave boundary layerinteraction was investigated for an inlet Mach number of 0.69.A lambda shock wave was seen on the downstream side of thebump. The velocity on both sides of the shock wave as measuredwith the PIV was in good agreement with theory. The shock wavewas found to cause boundary layer separation, which was seen asa rapid growth of the boundary layer thickness downstream theshock. However, no back ow was seen in the PIV-data, probablybecause the seeding did not give enough particles in theseparated region. The PIV data also showed that the shock wavewas oscillating, i.e. it was moving approximately 5 mm back andforth. This distance corresponds to about five boundary layerthicknesses in terms of the boundary layer upstream theshock.</p><p><b>Descriptors:</b>Fluid mechanics, compressible ow,turbulence, boundary layer, hot-wire anemometry, PIV, shockwave boundary layer interaction, shape factor.</p>

The design and optimisation of a modern gasoline direct injection (GDI) engine requires a thorough understanding of the fuel sprays characteristics and atomisation process.Therefore this thesis presents a detailed optical analysis of atomisation, penetration and interaction of multi-stream GDI sprays under engine relevant pressures and temperatures. The characteristics of the fuel spray in a GDI engine have a great influence on the fuel-air mixing and combustion processes as fuel injectors must provide adequate atomisation for vaporisation of the fuel to take place before combustion is initiated, whilst also avoiding spray impingement on the cylinder walls or piston crown. In this study multi-stream injectors, to be used within GDI engines, are quantified using Laser Doppler Anemometry (LDA) on an atmospheric bench. This process allowed for highly detailed spray analysis of droplet velocities and diameter at precise locations, using a three dimensional traverse, within the injector spray. The aim of the study was to analyse plume interaction between separate plumes of multi-stream injectors. Three multi-stream injectors were subjected to testing; two six-hole injectors and one three-hole injector. The injectors differed by having different distances between the plumes. The effect of fuel type on the liquid break-up and atomisation was investigated using Phase Doppler Anemometry (PDA) and Mie imaging. Mie imaging was also performed to capture images of fuel from a multi-stream injector as it was sprayed into a pressure chamber which was used to recreate the conditions found in an engine likely to cause flash boiling. In total, five variables were investigated: fuel pressure, ambient pressure, ambient temperature, fuel composition and injector geometry. Once processed, the recorded images allowed measurement of spray tip penetration and cone angle. Qualitative data on the change in shape of the spray was also available. The results showed that flash boiling has potential to reduce droplet diameters and improve fuel vaporisation, however, the associated change in spray shape must be taken into account to avoid problems with spray impingement. Keywords: Gasoline Direct Injection, multi-stream injector, atomisation, penetration, cone angle, Mie imaging, Phase Doppler Anemometry, flash boiling.

There is a need for wind sensors with high accuracy and measurement frequency for deployment on the surface of Mars. The wind data obtained to date have been adversely affected by thermal contamination and calibration issues. Improved data would not only help to constrain and validate theoretical models, but also increase safety and longevity of lander operations. The mechanical and thermal wind sensing techniques used on previous missions, whilst sufficient for basic meteorology, are wholly inadequate for measuring fundamental phenomena such as dust and volatile transport. Two promising technologies, optical and acoustic anemometry, could permit precise and high-frequency measurement of three-dimensional wind speeds on the Martian surface. Ultrasonic acoustic anemometry, which relies on time-of-flight measurements, was ultimately chosen for its lower processing requirements and ability to measure the speed of sound; and therefore temperature. Capacitive transducers were selected for their low impedance and high sensitivity, to maximise signal transmission through the rarefied Martian atmosphere. These transducers, which consist of a metallised polymer film oscillating on top of a contoured metal backplane, were evaluated for their suitability as anemometers on the Martian surface. A theoretical framework was assembled to model transducer performance and determine which factors are the most important in determining received signal amplitude. A pair of transducers were designed and manufactured to allow for testing of a wide range of parameters including thickness of the oscillating membrane and diameter. Tests were carried out on the assembled transducers to investigate the dependence on these parameters, and their behaviour was generally found to fit the assembled theoretical framework well. Transducer performance was highly dependent on roughness depth of the backplanes, as expected. The frequency response of the transducers was dominated by the backplane roughness at atmospheric pressure but by film thickness at low pressures. Cross-correlation of the sent and received signals was confirmed as the most reliable signal detection method at low signal amplitudes. The transducers were tested under simulated Martian conditions (a low-pressure carbon dioxide atmosphere with airborne dust), and found to be capable of accurately and reliably measuring the incident wind speed. The cumulative deposition of airborne dust noticeably reduced received signal amplitude, but further testing is required to determine the effect of significant amounts of dust on transducer performance. The impact of the transducer heads impeding the incident fluid flow was found to be very significant in wind tunnel testing. Preliminary computational models were found to accurately predict these effects, but a more comprehensive modelling campaign and experimental validation would be required to ensure accurate instrument calibration.

This thesis is motivated by the necessity to understand the flow structure of turbulent flows in bends encountered in many technical applications such as heat exchangers, nuclear reactors and internal combustion engines. Flows in bends are characterised by strong secondary motions in terms of counter-rotating vortices (Dean cells) set up by a centrifugal instability. Specifically the thesis deals with turbulent flows in 90° curved pipes of circular cross-section with and without an additional motion, swirling or pulsatile, superposed on the primary flow.  The aim of the present thesis is to study these complex flows in detail by using time-resolved stereoscopic particle image velocimetry to obtain the three-dimensional velocity field, with complementary hot-wire anemometry and laser Doppler velocimetry measurements. In order to analyse the vortical flow field proper orthogonal decomposition (POD) is used. The so called ``swirl-switching'' is identified and it is shown that the vortices instantaneously, ``rock'' between three states, viz. a pair of symmetric vortices or a dominant clockwise or counter-clockwise Dean cell. The most energetic mode exhibits a single cell spanning the whole cross-section and ``rolling'' (counter-)clockwise in time. However, when a honeycomb is mounted at the inlet of the bend, the Dean vortices break down and there is strong indication that the ``swirl-switching'' is hindered. When a swirling motion is superimposed on the incoming flow, the Dean vortices show a tendency to merge into a single cell with increasing swirl intensity. POD analysis show vortices which closely resemble the Dean cells, indicating that these structures co-exist with the swirling motion. In highly pulsating turbulent flow at the exit of a curved pipe, the vortical pattern is diminished or even eliminated during the acceleration phase and then re-established during the deceleration. In order to investigate the effect of pulsations and curvature on the performance of a turbocharger turbine, highly pulsating turbulent flow through a sharp bend is fed into the turbine. Time-resolved pressure and mass-flow rate measurements show that the hysteresis loop in the pressure-ratio-mass-flow plane, may differ significantly between straight and curved inlets, however the mean operating point is only slightly affected. / <p>QC 20140523</p>

Made available in DSpace on 2014-06-11T19:23:39Z (GMT). No. of bitstreams: 0 Previous issue date: 2005-12-16Bitstream added on 2014-06-13T19:06:57Z : No. of bitstreams: 1 eguti_cca_me_ilha.pdf: 4013696 bytes, checksum: 9efc5c11950fccddb62667186e778ef2 (MD5) / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) / Anemômetros de fio quente são sensíveis instrumentos capazes de medir variações de velocidade nos mais diversos tipos de escoamentos, sejam eles gasosos ou líquidos. Um delicado filamento metálico é aquecido por uma corrente elétrica a qual gera calor por efeito Joule e transfere parte dessa energia para o escoamento incidente, sendo esta troca de calor proporcional a velocidade do fluído, definindo assim o princípio básico de funcionamento da anemometria de fio quente. Quando este filamento é montado num circuito tipo ponte de Wheatstone, pode-se relacionar a troca de calor no filamento através da variação de sua resistência elétrica fazendo o uso de circuitos eletrônicos especiais. Este trabalho aborda os conceitos básicos da anemometria de fio quente, seus circuitos de controle principais e seus modos de operação, mostrando diferentes métodos para calibração de sondas de fio quente em escoamentos gasosos, além de apresentar uma metodologia completa para construção de um sistema básico de anemômetro de fio quente de temperatura constante. Dois dispositivos foram construídos e testados sendo avaliados quanto ao seu funcionamento e sua resposta em freqüência. / Hot wire anemometers are sensitive instruments capable of measuring fluctuation of speed in many fluid flows, gaseous or liquid. A delicate metallic filament is heated by an electric current (Joule effect) and cooled by incident flow, this heat exchange is proportional of the fluid speed, defining the basic phenomenon of hot-wire anemometry. When this filament is mounted on an arm of Wheatstone bridge, the heat lost by the filament can be related its electric resistance when special electronic circuits are used. This work presents the concepts of hot-wire anemometry, its main control circuits and its operation mode, showing the basic methods for hot wire calibration with gaseous flows, besides presenting a complete methodology for construction of a basic constant temperature hot-wire anemometer system, based on the tests of two experimental circuits which are evaluated by electronic tests and its frequency response.

This thesis consists of description of design and construction of device for measuring air velocity created in it´s practical part. In introduction is mentioned basic theoretical information related to given problem, in the next chapters is descripted design and construction of measuring device along with description of calibration proces. At the end is placed chapter about testing the final device.

This diploma thesis deals with matte coatings for 3D scanning purposes. The coatings are made with spray gun which uses a vibrating membrane atomizer and air blow gun. A suspension of titanium dioxide and alcohol is used as a coating material. This thesis describes the effect of the spray gun process parameters on the deposited coatings. These include, for example type of the coating suspension or setup of the blow gun. Phase Doppler Anemometry was used to measure spray characteristics. Deposited coatings were measured with profilometer and scanned with 3D scanner to study their thickness and effect on the results of 3D reconstruction. The result of this work was the coating with thickness below 1 µm with good optical properties for 3D scanning purposes. Standard deviation of the captured point cloud from the reference plane was below 0.0011 mm.

The compressible turbulent boundary layer developing over atwo-dimensional bump which leads to a supersonic pocket with aterminating shock wave has been studied. The measurements havebeen made with hot-wire anemometry and Particle ImageVelocimetry (PIV). A method to calibrate hot-wire probes in compressible ow hasbeen developed which take into account not only the ow velocitybut also the inuence of the Mach number, stagnation temperatureand uid density. The calibration unit consists of a small jetow facility, where the temperature can be varied. The hot wiresare calibrated in the potential core of the free jet. The jetemanates in a container where the static pressure can becontrolled, and thereby the gas density. The calibration methodwas verfied in the at plate zero pressure gradient turbulentboundary layer in front of the bump at three different Machnumbers, namely 0.3, 0.5 and 0.7. The profiles were alsomeasured at different static pressures in order to see theinuence of varying density. Good agreement between the profilesmeasured at different pressures, as well as with the standardlogarithmic profile was obtained. The PIV measurements of the boundary layer ow in front ofthe 2D bump showed good agreement with the velocity profilesmeasured with hotwire anemometry. The shock wave boundary layerinteraction was investigated for an inlet Mach number of 0.69.A lambda shock wave was seen on the downstream side of thebump. The velocity on both sides of the shock wave as measuredwith the PIV was in good agreement with theory. The shock wavewas found to cause boundary layer separation, which was seen asa rapid growth of the boundary layer thickness downstream theshock. However, no back ow was seen in the PIV-data, probablybecause the seeding did not give enough particles in theseparated region. The PIV data also showed that the shock wavewas oscillating, i.e. it was moving approximately 5 mm back andforth. This distance corresponds to about five boundary layerthicknesses in terms of the boundary layer upstream theshock. <b>Descriptors:</b>Fluid mechanics, compressible ow,turbulence, boundary layer, hot-wire anemometry, PIV, shockwave boundary layer interaction, shape factor. / NR 20140805

Despite its importance in various industrial applications there is still a lack of experimental studies on the dynamic and thermal field of swirling jets in the near-field region. The present study is an attempt to close this lack and provide new insights on the effect of rotation on the turbulent mixing of a passive scalar, on turbulence (joint) statistics as well as the turbulence structure. Swirl is known to increase the spreading of free turbulent jets and hence to entrain more ambient fluid. Contrary to previous experiments, which leave traces of the swirl generating method especially in the near-field, the swirl was imparted by discharging a slightly heated air flow from an axially rotating and thermally insulated pipe (6 m long, diameter 60 mm). This gives well-defined axisymmetric streamwise and azimuthal velocity distributions as well as a well-defined temperature profile at the jet outlet. The experiments were performed at a Reynolds number of 24000 and a swirl number (ratio between the angular velocity of the pipe wall and the bulk velocity in the pipe) of 0.5. By means of a specially designed combined X-wire and cold-wire probe it was possible to simultaneously acquire the instantaneous axial and azimuthal velocity components as well as the temperature and compensate the former against temperature variations. The comparison of the swirling and non-swirling cases clearly indicates a modification of the turbulence structure to that effect that the swirling jet spreads and mixes faster than its non-swirling counterpart. It is also shown that the streamwise velocity and temperature fluctuations are highly correlated and that the addition of swirl drastically increases the streamwise passive scalar flux in the near field. / QC 20101124