Lab-on-a-chip devices are changing the way that medical testing is performed by allowing rapid testing with small samples. Optofluidic biosensors are a type of lab-on-a-chip device that use light excitation on a fluid sample. One such application of an optofluidic biosensor is a device that can detect antibiotic resistant bacteria by combining DNA from a sample with fluorescent beads, flowing that sample through a hollow channel, and shining laser light on the channel. If the bacteria tested for is present, the fluorescent beads will give off photons that can be detected as a positive signal. The main method for illumination for these devices has been coupling light through a fiber optic cable to a waveguide on the side of the chip. Though effective, this method is impractical in a real world setting such as a hospital due to the difficulty of aligning to the side of the device. One solution to this problem is the use of illumination from the top of the device. Top-down illumination allows for more alignment flexibility, but also introduces the risk of additional noise or false signal as extra light reflects of the device. This dissertation discusses the viability and development of top-down illumination for optofluidic biosensors. This includes the development of an anti-reflective layer compatible with optofluidic biosensors, comparison of top-down illumination to side illumination, and simulations of various methods of performing top-down illumination. Based on the research and findings discussed in this dissertation, it has been found that top-down illumination is a viable illumination method for optofluidic biosensors. Additionally, the use of a pattern of laser lines combined with a light blocking anti-reflective layer is the recommended method for top-down illumination.

Research was conducted on broadband, anti-reflective coatings for fused silica and chalcogenide substrates in the infrared region of light. Using chemical preparation to create nano-porous through nano-particle based sol-gel solutions, the alteration of optical properties including refractive index and optical thickness was conducted. The nano-particles can modify the coating surface to allow only zero-order diffracted wave propagation reducing scattering while a partially graded profile of refractive index due surface evaporation lessened the precise phase relations of typical homogeneous coatings. My study of silica and titania sol-gel, and hybrid mixtures of the two were used to obtain the optical properties of the materials. The choice of experiments were rooted in theoretically calculated values, and parameters were selected based on quarter wavelength thickness and square root of refractive index theories of destructive cancellation of rebound waves for reduction of reflection. The fused silica system required anti-reflection in the region of 1.0-1.6 micrometer wavelength of the near-infrared. The base, uncoated transmission in this region is ~91%. A maximum transmission of 98% and no less than 97.3% over the entire region of interest was achieved. The chalcogenide system required anti-reflection in the regions of 1.0-1.6 and 3.5-5.0 micrometers of the near- and mid-infrared. The base, uncoated transmission of these regions is 61.9%. A maximum of 95% transmission was achieved for the 1.0-1.6 region and 87% for the 3.5-5.0 region. Solutions and coatings were characterized by Scanning Electron Microscope, Atomic Force Microscopy, X-ray Photoelectron Spectroscopy, particle size, elipsometry, UV-Vis-NIR, and FTIR to reveal the science behind the development and synthesis of nano optical coatings.

abstract: Transparent conductive oxides (TCOs) are used as electrodes for a number of optoelectronic devices including solar cells. Because of its superior transparent and conductive properties, indium (In) tin (Sn) oxide (ITO) has long been at the forefront for TCO research activities and high-volume product applications. However, given the limited supply of In and potential toxicity of Sn-based compounds, attention has shifted to alternative TCOs like ZnO doped with group-III elements such as Ga and Al. Employing a variety of deposition techniques, many research groups are striving to achieve resistivities below 1E-4 ohm-cm with transmittance approaching the theoretical limit over a wide spectral range. In this work, Ga-doped ZnO is deposited using pulsed laser deposition (PLD). Material properties of the films are characterized using a number of techniques. For deposition in oxygen at pressures >1 mTorr, post-deposition annealing in forming gas (FG) is required to improve conductivity. At these higher oxygen pressures, thermodynamic analysis coupled with a study using the Hall effect measurements and photoluminescence spectroscopy suggest that conductivity is limited by oxygen-related acceptor-like defects in the grains that compensate donors, effectively reducing the net carrier concentration and creating scattering centers that reduce electron mobility. Oxygen is also responsible for further suppression of conductivity by forming insulative metal oxide regions at the grain edges and oxygen-related electron traps at the grain boundaries. The hydrogen component in the FG is thought to passivate the intra-grain acceptor-like defects and improve carrier transport across these grain boundaries. Given this deleterious effect of oxygen on conductivity, depositions are performed in pure argon (Ar), i.e., the only oxygen species in the growth ambient are those ejected directly from the PLD solid source target. Ga-doped ZnO deposited in Ar at 200 °C and 10 mTorr have resistivities of 1.8E-4 ohm-cm without the need for post deposition annealing. Average transmittance of the Ga-doped films is 93% over the visible and near infrared (IR) spectral regions, but free carrier absorption is a limiting factor further into the IR. After annealing in FG at 500 °C, a 300 nm Ar film has a Haacke figure of merit of 6.61E-2 sq. ohm. / Dissertation/Thesis / Ph.D. Materials Science and Engineering 2011

This thesis reports the fabrication of nanophotonic structures by using electron beam lithography and using pattern transfer via self assembly with the aid of block copolymers. A theoretical and experimental basis was developed for fabricating anti-reflective coatings using block-copolymer pattern transfer. Block-copolymers were also used to fabricate plasmonic pattern arrays which form gold dots on glass surface. Electron-beam lithography was utilized to fabricate holey plasmonic structures from gold and silver films. Electron-beam exposure was used in block-copolymer lithography in selected regions. The exposure effects were studied for both thin and thick block-copolymer films. Reactive and ion beam etching techniques were used and optimized to fabricate those structures. This research required a great deal of development of new fabrication methods and key information is included in the body of the thesis.

Implementation of solar power by photovoltaic modules in cold climates, such as northern Sweden, implies several challenges. Ice and snow coverage not only leads to reduction in energy production due to shading, but it also puts equipment at risk from additional weight. The goal of this thesis was to formulate a passive ice shedding coating for photovoltaics that could handle the demands of both high optical transmittance and durability. In addition, the coating should be environmentally friendly and low cost. For that purpose, a state-of-the-art, superhydrophobic sol-gel silica-based coating was selected with the focus on optimizing its transparency, wettability, and durability. Different concentrations of binder, tetraethyl orthosilicate (TEOS), and catalyst (HCl) in the sol were explored, as well as post-treatment temperatures and sol aging, Hydrophobization was done by self-assembly of a silane and plasma polymerization of a siloxane. The coatings were characterized by UV-Vis spectroscopy, contact angle measurements, Scanning Electron Microscopy (SEM), X-ray Photoelectron Spectroscopy (XPS), tape peel strength, freeze-thaw cycling, ice adhesion force and a field test. Superhydrophobic, anti-reflective coatings with high transmittance (88.5±1.9%) were achieved, with some of them retaining their superhydrophobic properties after 15 freeze-thaw cycles between room temperature and -20°C. The main findings were that the amount of TEOS in the sol has the largest influence on transmittance and strength, with more TEOS leading to less transparent but stronger coatings, and that calcination of the coatings greatly improves their durability.

Orientador: Francisco das Chagas Marques / Dissertação (mestrado) - Universidade Estadual de Campinas, Instituto de Fisica Gleb Wataghin / Made available in DSpace on 2018-08-12T20:56:17Z (GMT). No. of bitstreams: 1 Silva_DouglasSoaresda_M.pdf: 1607458 bytes, checksum: 64efea4eea6490352c0cec9182778a67 (MD5) Previous issue date: 2009 / Resumo: Nesta tese estamos propondo o uso de carbono amorfo como um possível candidato para uso como camada antirrefletora em células solares de silício cristalino. O carbono amorfo pode ser preparado com alta banda proibida e tem propriedades importantes como alta dureza, baixo coeficiente de atrito, preparado à temperatura ambiente, etc. Além disso, o carbono amorfo é um material abundante na natureza e seu uso em eletrônica poderia reduzir o consumo de materiais tóxicos, contribuindo para reduzir danos ao meio ambiente. Foram exploradas as propriedades óticas dos filmes de carbono e carbono de silício produzidos por diferentes métodos de deposição (RF Glow Discharge, RF Sputtering e FCVA_Filtered Cathodic Vacuum Arc) visando a aplicação como camadas antirrefletoras em células solares. O estudo de propriedades óticas dos filmes, como a banda proibida, índice de refração, coeficiente de absorção e reflexão integrada foram determinantes para as conclusões deste trabalho. Para isto foram importantes a fabricação de células solares e o estudo dos principais parâmetros fotovoltaicos: eficiência, corrente de curto circuito, tensão de circuito aberto e fator de preenchimento. As células solares de silício monocristalino foram desenvolvidas a partir da técnica amplamente difundida e conhecida através da difusão térmica de dopantes de fósforo, as chamadas homojunções pn. Diferentes estruturas antirrefletoras à base de carbono foram estudadas e comparadas. Assim, investigamos o uso de carbono tipo diamante (diamond-like carbon DLC), carbono tipo polimérico (polimeric-like carbon ¿ PLC), carbono tetraédrico (ta-C), carbeto de silício (a-CxS ix-1:H). Para efeito de comparação com camadas antirrefletoras convencionais, adotamos o dióxido de estanho (SnO2) depositado pela técnica de spray químico. Os resultados mostraram que filmes de carbono amorfo funcionam como camada antirefletora em células solares, embora não tenha sido possível encontrar em um único material todas as condições ideais para uma camada antirrefletora em silício cristalino. O carbeto de silício se mostrou bastante promissor como um composto à base de carbono e o próprio silício, sendo utilizado na fabricação do dispositivo e abundante na natureza. / Abstract: In this thesis we propose the use of amorphous carbon as a possible candidate for use as antireflective layer in crystalline silicon solar cells. The amorphous carbon can be prepared with high band gap and important properties such as high hardness, low coefficient of friction, prepared at room temperature, etc. Moreover, the amorphous carbon material is abundant in nature and its use in electronics could reduce the consumption of toxic materials, helping to reduce damage to the environment. We explored the optical properties of carbon films and carbon silicon produced by different methods of deposition (RF Glow Discharge, RF Sputtering and FCVA_Filtered Cathodic Vacuum Arc) to the application as antireflective coatings in solar cells. The study of optical properties of films, such as forbidden band, index of refraction, absorption coefficient and integrated reflection were crucial to the conclusions of this work. For that, it was important the manufacture of solar cells and the study of key photovoltaic parameters: efficiency, short-circuit current, open circuit voltage and fill factor. The single crystal silicon solar cells were developed from the widely known technique of thermal diffusion of phosphorus doping, the pn homojunctions. Different antireflective structures based on carbon were studied and compared. Thus, we investigated the use of carbon type diamond (diamond-like carbon DLC), carbon type polymer (polimeric-like carbon - PLC), tetrahedral carbon (ta-C), silicon carbide (a-CxSix-1: H). For purposes of comparison with conventional antireflective layers, we adopted the tin dioxide (SnO2) deposited by chemical spray technique. The results showed that films of amorphous carbon layer acts as antireflective coatings in solar cells, although it was not possible to find a single material in all ideal conditions for an antireflective layer in crystalline silicon. The silicon carbide wasvery promising as a compound based on carbon and the silicon, been used in the manufacture of the device and abundant in nature. / Mestrado / Mestre em Física

Plasmonic nanoparticles feature remarkable optical and electronic properties in consequence of the excitation of conduction band electrons by visible light, which leads to collective oscillations. This so called localized surface plasmon resonance (LSPR) is utilized in the fields of photovoltaics, sensing, catalysis and optoelectronics. Especially, the emergence of optical metasurfaces—subwavelength structured surfaces with properties typically not occurring for homogeneous materials—has attracted significant attention for the applications mentioned above. However, their fabrication is usually complex and the materials often lack in situ tunability. Here, a colloidal approach is demonstrated for the preparation of optical metasurfaces with tunable properties. They are based on plasmonic gold nanoparticles, which were coated with three different shell materials to provide three different functionalities when coupled to plasmonic mirrors: i) Dye-labeled silica coatings exhibit strong enhancement of their fluorescent properties, as shown in this extensive single particle study. ii) Hydrogel shells are applied to receive switchable electric and magnetic properties in response to swelling of the gel. iii) Electrochromic polymer coatings facilitate the preparation of anti-reflective metasurfaces that feature tunable efficiency by changing the pH or applying a voltage. In addition, mechano-tunable plasmonic lattices are demonstrated. The material is based on self-assembled gold nanoparticles, which are embedded in a transparent elastomer matrix and feature pronounced surface lattice resonances (SLR). These tunable resonances could be applied for lasing, strain sensing, or controlling catalytic reactions. / Plasmonische Nanopartikel besitzen bemerkenswerte optische und elektronische Eigenschaften, die sie für Anwendungen in Bereichen der Katalyse, Sensorik, Optoelektronik, sowie der Nanooptik prädestinieren. Ihre Eigenschaften beruhen auf der Anregung von Leitungsbandelektronen zu kollektiven Oszillationen durch sichtbares Licht. Diese sogenannte Oberflächenplasmonenresonanz ist insbesondere für optische Metaoberflächen von Interesse, also Materialien mit strukturierten Oberflächen im Größenbereich unterhalb der sichtbaren Wellenlängen, welche Charakteristika aufweisen, die bei homogenen Materialien typischerweise nicht auftreten. Sie werden allerdings häufig mit aufwendigen Methoden hergestellt und sind in situ nicht justierbar. In dieser Arbeit werden kolloidale Ansätze zur Herstellung plasmonischer Metaoberflächen mit einstellbaren optischen und elektronischen Eigenschaften vorgestellt. Das Konzept basiert auf der Verwendung von plasmonischen Goldkernen, die mit drei unterschiedlichen funktionellen Schalen beschichtet und anschließend mit plasmonischen Spiegeln gekoppelt wurden: i) Farbstoffmarkierte Silicapartikel zeigen starke Fluoreszenz-verstärkung, wie in dieser ausführlichen Einzelpartikelstudie nachgewiesen wird. ii) Hydrogelbeschichtungen werden verwendet um schaltbare elektrische und magnetische Eigenschaften mittels Quellung zu erzeugen. iii) Elektrochrome Polymerhüllen fungieren als Antireflexschicht auf Goldoberflächen, deren Extinktion sich mittels Anlegen einer Spannung oder durch pH-Änderungen einstellen lässt. Neben diesen Ansätzen werden mechanisch einstellbare plasmonische Gitterstrukturen vorgestellt. Die selbstassemblierten und in transparentem Elastomer eingebetteten Goldnanopartikel weisen eine ausgeprägte Oberflächengitterresonanz auf. Diese kann für sensorische Zwecke in den Bereichen der Mikromechanik und der Katalyse, sowie für abstimmbare Laser verwendet werden.

La microscopie optique sur substrats antireflets est un outil de caractérisation simple et puissant qui a notamment permis l'isolation du graphène en 2004. Depuis, le domaine d'étude des matériaux bidimensionnels (2D) s'est rapidement développé, tant au niveau fondamental qu'appliqué. Ces matériaux ultraminces présentent des inhomogénéités (bords, joints de grains, multicouches, etc.) qui impactent fortement leurs propriétés physiques et chimiques. Ainsi leur caractérisation à l'échelle locale est primordiale. Cette thèse s'intéresse à une technique récente de microscopie optique à fort contraste, nommée BALM, basée sur l'utilisation originale de couches antireflets très minces (2-5 nm) et fortement absorbantes (métalliques). Elle a notamment pour but d'évaluer les mérites de cette technique pour l'étude des matériaux 2D et de leur réactivité chimique. Ainsi, les différents leviers permettant d'améliorer les conditions d'observation des matériaux 2D ont tout d'abord été étudiés et optimisés pour deux matériaux modèles : l'oxyde de graphène et les monocouches de MoS₂. L'étude de la dynamique de dépôt de couches moléculaires a notamment permis de montrer à la fois l'extrême sensibilité de BALM pour ce type de mesures et l'apport significatif des multicouches antireflets pour l'augmentation du contraste lors de l'observation des matériaux 2D. L'un des atouts principaux de BALM venant de sa combinaison à d'autres techniques, nous nous sommes particulièrement intéressés au couplage de mesures optiques et électrochimiques pour lesquelles le revêtement antireflet sert d'électrode de travail. Nous avons ainsi pu étudier optiquement la dynamique de réduction électrochimique de l'oxyde de graphène (GO), l'électro-greffage de couches minces organiques par réduction de sels de diazonium sur le GO et sa forme réduite (r-GO), ainsi que l'intercalation d'ions métalliques entre feuillets de GO. En combinant versatilité et fort-contraste, BALM est ainsi établi comme un outil prometteur pour l'étude des matériaux 2D et en particulier pour la caractérisation locale et in situ de leur réactivité chimique et électrochimique. / Optical microscopy based on anti-reflective coatings is a simple yet powerful characterization tool which notably allowed the first observation of graphene in 2004. Since then, the field of two-dimensional (2D) materials has developed rapidly both at the fundamental and applied levels. These ultrathin materials present inhomogeneities (edges, grain boundaries, multilayers, etc.) which strongly impact their physical and chemical properties. Thus their local characterization is essential. This thesis focuses on a recent enhanced-contrast optical microscopy technique, named BALM, based on ultrathin (2-5 nm) and strongly light-absorbing (metallic) anti-reflective layers. The goal is notably to evaluate the benefits of this technique for the study of 2D materials and their chemical reactivity. The various levers to improve 2D materials observation were investigated and optimized for two model materials: graphene oxide and MoS₂ monolayers. The investigation of molecular layer deposition dynamic notably showed the extreme sensitivity of BALM for such measurements and the significant contribution of multilayers anti-reflective coatings to enhance contrast during the observation of 2D materials. One of the main assets of BALM comes from its combination to other techniques. We particularly considered the coupling between optical measurements and electrochemistry for which the anti-reflective layer serves as working electrode. We investigated optically the dynamic of electrochemical reduction of Graphene Oxide (GO), the electrografting of organic layers by diazonium salts reduction on GO and its reduced form (rGO), as well as the intercalation of metallic ions within GO sheets. By combining versatility and high-contrast, BALM is established as a promising tool for the study of 2D materials, especially for the local and in situ characterization of their chemical and electrochemical reactivity.