No description available.

A general approach to numerically simulating wear in rollingand sliding contacts is presented in this thesis. A simulationscheme is developed that calculates the wear at a detailedlevel. The removal of material follows Archard’s wear law,which states that the reduction of volume is linearlyproportional to the sliding distance, the normal load and thewear coefficient. The target application is the wheel-railcontact. Careful attention is paid to stress properties in the normaldirection of the contact. A Winkler method is used to calculatethe normal pressure. The model is calibrated either withresults from Finite Element simulations (which can include aplastic material model) or a linear-elastic contact model. Thetangential tractions and the sliding distances are calculatedusing a method that incorporates the effect of rigid bodymotion and tangential deformations in the contact zone.Kalker’s Fastsim code is used to validate the tangentialcalculation method. Results of three different sorts ofexperiments (full-scale, pin-on-disc and disc-on-disc) wereused to establish the wear and friction coefficients underdifferent operating conditions. The experimental results show that the sliding velocity andcontact pressure in the contact situation strongly influencethe wear coefficient. For the disc-on-disc simulation, therewas good agreement between experimental results and thesimulation in terms of wear and rolling friction underdifferent operating conditions. Good agreement was alsoobtained in regard to form change of the rollers. In thefull-scale simulations, a two-point contact was analysed wherethe differences between the contacts on rail-head to wheeltread and rail edge to wheel flange can be attributed primarilyto the relative velocity differences in regard to bothmagnitude and direction. Good qualitative agreement was foundbetween the simulated wear rate and the full-scale test resultsat different contact conditions. <b>Keywords:</b>railway rail, disc-on-disc, pin-on-disc,Archard, wear simulation, Winkler, rolling, sliding

<p>A general approach to numerically simulating wear in rollingand sliding contacts is presented in this thesis. A simulationscheme is developed that calculates the wear at a detailedlevel. The removal of material follows Archard’s wear law,which states that the reduction of volume is linearlyproportional to the sliding distance, the normal load and thewear coefficient. The target application is the wheel-railcontact.</p><p>Careful attention is paid to stress properties in the normaldirection of the contact. A Winkler method is used to calculatethe normal pressure. The model is calibrated either withresults from Finite Element simulations (which can include aplastic material model) or a linear-elastic contact model. Thetangential tractions and the sliding distances are calculatedusing a method that incorporates the effect of rigid bodymotion and tangential deformations in the contact zone.Kalker’s Fastsim code is used to validate the tangentialcalculation method. Results of three different sorts ofexperiments (full-scale, pin-on-disc and disc-on-disc) wereused to establish the wear and friction coefficients underdifferent operating conditions.</p><p>The experimental results show that the sliding velocity andcontact pressure in the contact situation strongly influencethe wear coefficient. For the disc-on-disc simulation, therewas good agreement between experimental results and thesimulation in terms of wear and rolling friction underdifferent operating conditions. Good agreement was alsoobtained in regard to form change of the rollers. In thefull-scale simulations, a two-point contact was analysed wherethe differences between the contacts on rail-head to wheeltread and rail edge to wheel flange can be attributed primarilyto the relative velocity differences in regard to bothmagnitude and direction. Good qualitative agreement was foundbetween the simulated wear rate and the full-scale test resultsat different contact conditions.</p><p><b>Keywords:</b>railway rail, disc-on-disc, pin-on-disc,Archard, wear simulation, Winkler, rolling, sliding</p>

The objectives of this research were to investigate the wear that occurs on the surface of a Hardcoat anodized die-cast aluminum surface, which was sliding against a composite rubber belt. This research investigated known wear theories and the results for previous testing to understand the mechanisms that were likely occurring in this application. These theories indicated that the wear occurring may be reduced by changing the hardness of the materials involved. Archard's equation gave tangible evidence of this fact, but related to the base material and not a surface coating. It was hypothesized that Hardcoat anodizing would follow the theory of Archard's equation and increase the wear resistance of 390 die-cast aluminum when sliding against a composite rubber belt. Standardized wear tests were implemented in order to test this theory. The results of the wear tests indicated that the wear resistance of the Hardcoat anodized coating did not follow the wear theories and wore at a higher rate than the base material surfaces. This is likely due to the phenomenon seen by Jiang and Arnell where the surface roughness influenced the wear rate of DLC coatings. They found that there existed a transition point where the wear rate of the surface increased with an increase of surface roughness. The Hardcoat anodized surface was rougher than the surface of the base material due to alloy materials and the processing characteristics of 390 Aluminum die-casting material. Subsequently the Hardcoat anodized surface wore at a higher rate than did the base surface. A case study was conducted on an ATV to investigate the accuracy of the results from the laboratory testing. This case study showed a significant localized wear groove in the stock CVT drive sheave with little wear occurring elsewhere. The Hardcoat anodized CVT drive sheave did not show evidence of a significant localized wear groove as the stock sheave but indicates that wear occurred more evenly across the surface. This wear is evident due to visible aluminum through the Hardcoat layer. In addition, there was a ridge at the outer diameter of the sheave where the belt could not wear the surface. Both of these items indicated that significant wear occurred on the surface, but the presence of a localized wear groove is non-existent.

Mobile Miner 40V is a machine used for rock excavation and developed by Epiroc. This machine is equipped with a large cutter wheel to perform the excavation. After a test run, some surfaces associated with bearings within the cutter wheel were found to be damaged due to scuffing - severe sliding wear. There is a static load applied to the surfaces due to gravity. However, the reason for this damaged issue was believed that there is a large dynamic load applied to the surfaces during the excavation. This dynamic load was not found in a previous FE model used to verify safety issues. Therefore, a new FE model that is more in line with reality, and a failure analysis were required. Additionally, a feasibility study for a cutter wheel with a larger dimension was also needed since a larger cutter wheel is desirable. Firstly, wear mechanisms were reviewed, and some theories were chosen to analyze the damaged issue. Since it was unknown whether the surfaces were well-lubricated or not, both cases were investigated. The Archard wear equation was used to analyze the poor-lubricated situation, while the lubrication number and the Reynolds equation were used to analyze the well-lubricated case. Secondly, contact mechanisms between the surfaces were also investigated. The investigation of the contact mechanisms involved several theories, such as the Hertzian contact theory and the impact load factor. Besides these theoretical analyses, a numerical analysis was performed. Lastly, a new FE model was established in Ansys. Both the cutter wheel which was subjected to scuffing(existing cutter wheel), and the cutter wheel with a larger dimension(larger cutter wheel) were analyzed by the use of the new FE model. The maximum and minimum wear rates obtained by the Archard wear equation are approximately 1.9・10-2mm3/m and 4.8・10-3mm3/m, which are considered as a completely unacceptable level in engineering applications. The maximum and minimum critical loads obtained by the Reynold equation are approximately 1.8kN and 24.8kN, which both are larger than the static load applied to the surfaces. The maximum and minimum critical mean contact pressures obtained by the lubrication number are approximately 65MPa and 240MPa, which both are larger than the mean contact pressure generated by the static load. No evidence shows that there is a large dynamic load applied to the surfaces during the excavation. The largest possible contact pressure on the bearings in the existing cutter wheel is very close to the limit of severely damaged. The largest possible contact pressure on the bearings in the larger cutter wheel is believed to exceed the limit of severely damaged. The previous assumption that the surfaces were damaged due to a large dynamic load was wrong. The obtained results support that the surfaces were only subjected to a static load and were damaged due to inadequate lubrication. The existing cutter wheel is operated safely with the current load cases. However, the forward thrust force is suggested to decrease when the cutting angle is large. There is a high risk if the larger cutter wheel is operated with the current load cases.