Cross median crashes have become a serious problem in recent years. Most of the median cross sections used for divided highways have terrains with steep slopes. Traffic barriers, frequently used on slopes, are generally designed based on the findings obtained from crash tests performed on flat terrain. For barriers placed on roadside and median slopes, vehicle impact height varies depending on the trajectory of the vehicle along the ditch section and lateral offset of the barrier. Thus depending on the placement location on a relatively steep slope, a barrier can be impacted by an errant vehicle at height and orientation more critical compared to those considered during its design. Hence, detailed study of performance of barriers on roadside and median slopes is needed to achieve acceptable safety performance. In this study, performances of modified G4(1S) W-beam, Midwest Guardrail System (MGS), modified Thrie-beam, modified weak post W-beam, and box-beam guardrail systems on sloped terrains are investigated using numerical simulations. A procedure is developed that provide guidance for their placement on roadside and median slopes. The research approach consists of nonlinear finite element analyses and multi-rigid-body dynamic analyses approach. Detailed finite element representation for each of the barriers is developed using LS-DYNA. Model fidelity is assessed through comparison of simulated and measured responses reported in full scale crash test studies conducted on flat terrain. LS-DYNA simulations of vehicle impacts on barriers placed on flat terrain at different impact heights are performed to identify performance limits of the barriers in terms of acceptable vehicle impact heights. The performances of the barriers are evaluated following the guidelines provided in NCHRP Report 350. Multi-rigid-body dynamic analysis code, CARSIM, is used to identify trajectories of the vehicles traversing various roadside and median cross-slopes. After analyzing vehicle trajectories and barrier performance limits, a guideline has been prepared with recommendations for the placement of barriers along roadside and median slopes. This guideline is then verified and refined using the responses obtained from full-scale LS-DYNA simulations. These simulations capture the full encroachment event from departure of the vehicle off the traveled way through impact with the barrier.

京都大学 / 0048 / 新制・論文博士 / 博士(地球環境学) / 乙第12827号 / 論地環博第7号 / 新制||地環||24(附属図書館) / 31314 / (主査)教授 勝見 武, 教授 三村 衛, 准教授 乾 徹 / 学位規則第4条第2項該当 / Doctor of Global Environmental Studies / Kyoto University / DFAM

<p>Transport of gasses and liquids through polymers and composites is an important factor to be considered when designing a material for structure and packaging applications. For structural engineering applications, more focus has been given to the transportation of water, vapor and organic liquids rather than gases as diffusion of these liquids into the polymers and polymer-based composites can significantly lower service life. In addition, much attention has been given to the leaching of unreacted reactant molecules, solvents, additives, degradation products from the polymers and composites to the atmosphere (water, soil etc.). We studied the transport of volatile organic compounds and water in cured-in-place-pipe (CIPP) (a representative of FRPC) and gas permeability of highly engineered cellulose nanocrystals (CNC) films.</p> <p>Cured-in-place-pipe (CIPP) is a popular technology which uses fiber reinforced polymer composite to repair sanitary sewer, stormwater, and drinking water pipe. The liner is installed in the field and exposed to flowing water immediately after installation (curing of the liner) is done. Curing conditions dictate liner properties as undercured liners can contain unreacted styrene monomers, additives, degradation products. These agents can leach out and enter the environment (soil, water, air). The objective of this work was to investigate the curing behavior, volatile content, thermal stability of steam-cured and UV-cured CIPP liners collected from Indiana and New York installation sites. The liner specimens were also exposed to water and other aggressive environmental conditions (saltwater, concrete pore solution at 50 °C) to explore the leaching of unreacted styrene and other organic chemicals from the liners. The influence of transportation of water, salt solution and pore solution through liners on mechanical and thermo-mechanical properties was also examined to study the durability of the liners. Study suggested that the durability of the liners depends on the curing condition and exposed environment conditions.</p> <p>The function of polymer packaging materials is mainly to inhibit gas and moisture permeation through the films. Cellulose nanocrystals (CNCs) have drawn growing interest for the packaging due to their non-toxicity, abundance in nature, biodegradability and high barrier properties. The objective of this work was to corelate the alignment of CNC with free volume and barrier performance of the film. Furthermore, citric acid (CA) was added to the CNC suspensions with varying quantity to explore the effect of CA on coating quality and barrier performance of CNC coated polypropylene (PP) film. Study revealed that CA addition in CNC suspension can enhance the hydrophobicity and gas barrier performance of coated PP films while retaining the high optical transparency. </p>