This study aims to produce a type of concrete with both good thermal and mechanical properties by using environmentally friendly and low cost materials. In addition, the resistance of this concrete to fire conditions was investigated. The experimental work comprises two parts. In the first part, recycled glass was used as a partial replacement for natural sand (at proportions 20%, 40% and 60%) together with basalt fibre having different volume fractions (0.1%, 0.3%, and 0.5%). The results obtained from the experimental work showed that the optimum content is 20% glass and at 28 days, there was a 4.23% and 15% enhancement in the compressive strength and the splitting tensile strength respectively. Above 20% glass there was a slight reduction (6.6% and 22%) in the compressive strength and the splitting tensile strength when 60% glass was used. The results also showed that when glass sand and basalt fibre content increase, there is a decrease in the thermal conductivity range from 4.35% to 50% at temperature levels between 60oC to 600oC. The structural behaviour of this type of concrete was investigated in the second part of this study by carrying out small-scale slab tests at ambient and elevated temperatures. The results show that there is an increase in the load carrying capacity above the theoretical yield line load, due to membrane action, for all percentages of glass and volume fractions of basalt fibre ranging from 1.35 to 1.68 for the slab tested at ambient temperature and from 3.13 to 3.26 for the slabs tested at elevated temperature. Also the slabs with higher glass sand and basalt fibre content had a higher load enhancement and failed at a higher displacement compared to the control mix.A comparison between the simplified method and the finite element software package ABAQUS showed that the ABAQUS model gives reasonable predictions for the load-vertical displacement and the temperature-displacement relationships at both ambient and elevated temperature conditions, while the simplified method gives conservative predictions for the maximum allowable vertical displacement for the slab at elevated temperature. A parametric study showed that a 10 mm cover depth is the optimum depth as well as the reinforcement temperature predicted reduced with increasing load ratio (applied load/yield line load).

This paper presents test results and code predictions of four continuously and two simply supported concrete slabs reinforced with basalt fibre reinforced polymer (BFRP) bars. One continuously supported steel reinforced concrete slab was also tested for comparison purposes. All slabs tested were 500 mm in width and 150 mm in depth. The simply supported slabs had a span of 2000 mm, whereas the continuous slabs had two equal spans, each of 2000 mm. Different combinations of under and over BFRP reinforcement at the top and bottom layers of slabs were investigated. The continuously supported BFRP reinforced concrete slabs exhibited larger deflections and wider cracks than the counterpart reinforced with steel. Furthermore, the over reinforced BFRP reinforced concrete slab at the top and bottom layers showed the highest load capacity and the least deflection of all BFRP slabs tested. All continuous BFRP reinforced concrete slabs failed owing to combined shear and flexure at the middle support region. ISIS-M03-07 and CSA S806-06 design guidelines reasonably predicted the deflection of the BFRP slabs tested. However, ACI 440-1R-06 underestimated the BFRP slab deflections and overestimated the moment capacities at mid-span and over support sections.

An investigation on the application of basalt fibre reinforced polymer (BFRP) and carbon fibre reinforced polymer (CFRP) bars as longitudinal reinforcement for simple and continuous concrete slabs is presented. Eight continuously and four simply concrete slabs were constructed and tested to failure. Two continuously supported steel reinforced concrete slabs were also tested for comparison purposes. The slabs were classified into two groups according to the type of FRP bars. All slabs tested were 500 mm in width and 150 mm in depth. The simply supported slabs had a span of 2000 mm, whereas the continuous slabs had two equal spans, each of 2000 mm. Different combinations of under and over FRP (BFRP/CFRP) reinforcement at the top and bottom layers of slabs were investigated. The continuously supported BFRP and CFRP reinforced concrete slabs exhibited larger deflections and wider cracks than the counterpart reinforced with steel. The experimental results showed that increasing the bottom mid-span FRP reinforcement of continuous slabs is more effective than the top over middle support FRP reinforcement in improving the load capacity and reducing mid-span deflections. Design guidelines have been validated against experimental results of FRP reinforced concrete slabs tested. ISIS-M03-07 and CSA S806-06 equations reasonably predicted the deflections of the slabs tested. However, ACI 440-1R-06 underestimated the deflections, overestimated the moment capacities at mid-span and over support sections, and reasonably predicted the load capacity of the continuous slabs tested. On the analytical side, a numerical technique consisting of sectional and longitudinal analyses has been developed to predict the moment-curvature relationship, moment capacity and load-deflection of FRP reinforced concrete members. The numerical technique has been validated against the experimental test results obtained from the current research and those reported in the literature. A parametric study using the numerical technique developed has also been conducted to examine the influence of FRP reinforcement ratio, concrete compressive strength and type of reinforcement on the performance of continuous FRP reinforced concrete slabs. Increasing the concrete compressive strength decreased the curvature of the reinforced section with FRP bars. Moreover, in the simple and continuous FRP reinforced concrete slabs, increasing the FRP reinforcement at the bottom layer fairly reduced and controlled deflections.

An investigation on the application of basalt fibre reinforced polymer (BFRP) and carbon fibre reinforced polymer (CFRP) bars as longitudinal reinforcement for simple and continuous concrete slabs is presented. Eight continuously and four simply concrete slabs were constructed and tested to failure. Two continuously supported steel reinforced concrete slabs were also tested for comparison purposes. The slabs were classified into two groups according to the type of FRP bars. All slabs tested were 500 mm in width and 150 mm in depth. The simply supported slabs had a span of 2000 mm, whereas the continuous slabs had two equal spans, each of 2000 mm. Different combinations of under and over FRP (BFRP/CFRP) reinforcement at the top and bottom layers of slabs were investigated. The continuously supported BFRP and CFRP reinforced concrete slabs exhibited larger deflections and wider cracks than the counterpart reinforced with steel. The experimental results showed that increasing the bottom mid-span FRP reinforcement of continuous slabs is more effective than the top over middle support FRP reinforcement in improving the load capacity and reducing mid-span deflections. Design guidelines have been validated against experimental results of FRP reinforced concrete slabs tested. ISIS¿M03¿07 and CSA S806-06 equations reasonably predicted the deflections of the slabs tested. However, ACI 440¿1R-06 underestimated the deflections, overestimated the moment capacities at mid-span and over support sections, and reasonably predicted the load capacity of the continuous slabs tested. On the analytical side, a numerical technique consisting of sectional and longitudinal analyses has been developed to predict the moment¿curvature relationship, moment capacity and load-deflection of FRP reinforced concrete members. The numerical technique has been validated against the experimental test results obtained from the current research and those reported in the literature. A parametric study using the numerical technique developed has also been conducted to examine the influence of FRP reinforcement ratio, concrete compressive strength and type of reinforcement on the performance of continuous FRP reinforced concrete slabs. Increasing the concrete compressive strength decreased the curvature of the reinforced section with FRP bars. Moreover, in the simple and continuous FRP reinforced concrete slabs, increasing the FRP reinforcement at the bottom layer fairly reduced and controlled deflections.

In alkalischen Lösungen führt die Reaktion von Hydroxylionen mit den Si-O-Si-Bindungen des Glasnetzwerks zur Bildung hydratisierter Oberflächen und gelöstem Silikat. Der Grad der Korrosion bzw. der Alterung der Glasfaser ist abhängig von der chemischen Zusammensetzung des Glases und Korrosionslösung sowie von Zeit und Temperatur. Die Untersuchung von Glasfasern verschiedener chemischer Zusammensetzung in NaOH- sowie Zementlösungen zeigte, dass die inhibierende Wirkung von Ca-Ionen zu einem veränderten Korrosionsmechanismus führt. Dies konnte anhand der mechanischen Eigenschaften der Glasfasern sowie rasterelektronenmikroskopischen Untersuchungen gezeigt werden. Während die Korrosion in NaOH-Lösung zu einer ausgeprägten Umwandlung der gesamten äußeren Glasfaserschicht in Reaktionsprodukte führte, zeigten Glasfasern in Zementlösung bei gleichem pH-Wert einen stark lokal begrenzten, punktförmigen Angriff. Daraus resultieren unterschiedliche mechanische Eigenschaften der Glasfasern in Abhängigkeit von der gewählten Korrosionslösung.

In alkalischen Lösungen führt die Reaktion von Hydroxylionen mit den Si-O-Si-Bindungen des Glasnetzwerks zur Bildung hydratisierter Oberflächen und gelöstem Silikat. Der Grad der Korrosion bzw. der Alterung der Glasfaser ist abhängig von der chemischen Zusammensetzung des Glases und Korrosionslösung sowie von Zeit und Temperatur. Die Untersuchung von Glasfasern verschiedener chemischer Zusammensetzung in NaOH- sowie Zementlösungen zeigte, dass die inhibierende Wirkung von Ca-Ionen zu einem veränderten Korrosionsmechanismus führt. Dies konnte anhand der mechanischen Eigenschaften der Glasfasern sowie rasterelektronenmikroskopischen Untersuchungen gezeigt werden. Während die Korrosion in NaOH-Lösung zu einer ausgeprägten Umwandlung der gesamten äußeren Glasfaserschicht in Reaktionsprodukte führte, zeigten Glasfasern in Zementlösung bei gleichem pH-Wert einen stark lokal begrenzten, punktförmigen Angriff. Daraus resultieren unterschiedliche mechanische Eigenschaften der Glasfasern in Abhängigkeit von der gewählten Korrosionslösung.