No description available.

This study details the dielectrophoretic assembly and mechanical characterization of boron nitride nanotubes on silicon chips with gold electrodes. The chips were fabricated from 4in round silicon wafers with a 100nm-thick low stress silicon nitride insulating layer on the top and bottom. The electrodes were patterned using photo- and electron-beam lithography and dry etching, and the wafers were cut into 4 x 6mm chips. The boron nitride nanotubes studied were obtained from NIA and were synthesized via a unique pressurized vapor/condensor method, which produced long, small-diameter BNNTs without the use of a catalyst. These nanotubes were studied due to their desirable mechanical and electrical properties, which allow for unique applications in various areas of science, engineering, and technology. Applications span from magnetic manipulation to the formation of biocomposites, from nano-transistors to humidity and pH sensors, and from MRI contrast agents to drug delivery. The nanotubes and nanotube bundles characterized were suspended over gaps of 300 to 500nm. This study was unique in that assembly was performed using dielectrophoresis, allowing for batch fabrication of chips and devices. Also, stiffness measurements were performed using AFM, eliminating the reliance of other methods upon electron microscopes, and allowing for imaging and measurements to occur simultaneously and at high resolution. It was found that DEP parameters of V = 2.0Vpp, f = 1kHz, and t = 2min provided the best results for mechanical testing. The nanotubes tested had suspended lengths of 300nm, the width of the electrode gap, and diameters of 15–65nm. Chips were imaged with both scanning electron microscopy and atomic force microscopy. Force-displacement measurements with atomic force microscopy were used to find stiffness values in the range of 1–16N/m. These stiffness values, when plugged into a simple double-clamped beam model, indicated Young’s moduli of approximately 1–1600GPa. Within this wide range, it was shown that a decrease in diameter strongly correlated exponentially to an increase in Young’s modulus. Work in this study was divided between assembly and characterization. Therefore, a lot of time was spent working to optimize dielectrophoresis parameters, followed by SEM and AFM imaging. Parameters that were adjusted included DEP voltage and time, pre-DEP sonication times, as well as adding a centrifuging procedure to attempt to better separate nanotube bundles in solution. Another method discussed but not pursued was the use of surfactants to agitate the solution, thus separating the nanotubes. The reason this material in particular was so difficult to separate was twofold. First, the small size of the nanotubes—individual BNNTs have diameters on the order of ∼5 nanometers—generates very strong nanoscale van der Waals forces holding the nanotubes together. Larger nanotubes—with diameters on the order of 50 to 100nm or more—suffer less from this problem. Also, the dipoles created by the boron-nitrogen bonds cause attraction between adjacent nanotubes. The results shown in this thesis include DEP parameters, SEM and AFM images, and force- displacement curves leading to nanotube stiffness and Young’s modulus values. The force-displacement tests via AFM are also detailed and explained.

Several nanomaterials systems, both inorganic and organic in nature, have been extensively investigated by a number of characterization techniques including atomic force microscopy (AFM), electron microscopy, Fourier transform infrared spectroscopy (FTIR), and energy dispersive x-ray spectroscopy (EDX). The first system consists of boron nitride nanotubes (BNNTs) synthesized via two different methods. The first method, silica-assisted catalytic chemical vapour deposition (SA-CVD), produced boron nitride nanotubes with different morphologies depending on the synthesis temperature. The second method, growth vapour trapping chemical vapour deposition (GVT-CVD), produced multiwall boron nitride nanotubes (MWBNNTs). The bending modulus of individual MWBNNTs was determined using an AFM three-point bending technique, and was found to be diameter-dependent due to the presence of shear effects. The second type of nanomaterial investigated is the biomineralized calcareous shell of the serpulid Hydroides dianthus. This material was found to be an inorganic-organic composite material composed of two different morphologies of CaCO3, collagen, and carboxylated and sulphated polysaccharides. The organic components were demonstrated to mediate the mineralization of CaCO3 in vitro. The final system studied is the proteinaceous cement of the barnacle Amphibalanus amphitrite. The secondary structure of the protein components was investigated via FTIR, revealing the presence of β-sheet conformation, and nanoscale rod-shaped structures within the cement were identified as β-sheet containing amyloid fibrils via chemical staining. These rod-shaped structures exhibited a stiffer nature compared with other structures in the adhesive, as measured by AFM nanoindentation.

Several nanomaterials systems, both inorganic and organic in nature, have been extensively investigated by a number of characterization techniques including atomic force microscopy (AFM), electron microscopy, Fourier transform infrared spectroscopy (FTIR), and energy dispersive x-ray spectroscopy (EDX). The first system consists of boron nitride nanotubes (BNNTs) synthesized via two different methods. The first method, silica-assisted catalytic chemical vapour deposition (SA-CVD), produced boron nitride nanotubes with different morphologies depending on the synthesis temperature. The second method, growth vapour trapping chemical vapour deposition (GVT-CVD), produced multiwall boron nitride nanotubes (MWBNNTs). The bending modulus of individual MWBNNTs was determined using an AFM three-point bending technique, and was found to be diameter-dependent due to the presence of shear effects. The second type of nanomaterial investigated is the biomineralized calcareous shell of the serpulid Hydroides dianthus. This material was found to be an inorganic-organic composite material composed of two different morphologies of CaCO3, collagen, and carboxylated and sulphated polysaccharides. The organic components were demonstrated to mediate the mineralization of CaCO3 in vitro. The final system studied is the proteinaceous cement of the barnacle Amphibalanus amphitrite. The secondary structure of the protein components was investigated via FTIR, revealing the presence of β-sheet conformation, and nanoscale rod-shaped structures within the cement were identified as β-sheet containing amyloid fibrils via chemical staining. These rod-shaped structures exhibited a stiffer nature compared with other structures in the adhesive, as measured by AFM nanoindentation.

Boron nitride nanotubes (BNNTs), which are structurally similar to carbon nanotubes (CNTs), were synthesized in 1995 for the first time. They are made up by folding atom sheets which consist of boron and nitrogen atoms into cylindrical form. After their discovery, BNNTs have been attracting great attention due to their extraordinary mechanical, thermal, electrical, and optical properties. In this study, BNNTs were synthesized from the reaction of ammonia gas with the boron and iron powder mixture in a tubular reactor which was connected to a mass spectrometer for on-line chemical analysis of the reactor effluent stream. The synthesized materials were purified with acid treatment. Chemical analysis results showed that nitrogen and hydrogen gases were present in addition to ammonia gas. XRD results revealed that the solid phases in the synthesized material were hexagonal boron nitride, rhombohedral boron nitride, iron, and boron-iron compounds (FeB49 and Fe3B). Reactions taking place in BNNT synthesis were proposed as the decomposition of ammonia gas which was the only gas phase reaction, the formation of boron-iron compounds from the reaction of boron with iron, and boron nitride formation from the reaction of nitrogen with boron-iron compounds. Agglomerated, hollow, multi-walled nanotubes were synthesized with an outer diameter range of 10-550 nm. Both open and close-ended nanotubes were observed. The interlayer distance between BN sheets was measured about 0.33 nm and this distance indicated the d002 plane of hexagonal boron nitride. BNNTs exhibited Type II isotherms with a Type B hysteresis. A decrease in the surface area of the synthesized BNNTs was observed with an increase in temperature. The highest surface area was 147.6 m2/g. Average pore diameter of BNNTs synthesized at different temperatures was around 38 &Aring / . Deposition rate of boron nitride increased with an increase in temperature. After a certain temperature, deposition rate decreased with temperature due to the sintering effect. The highest deposition rate was observed when BNNTs were synthesized with the B/Fe weight ratio of 15/1 at 1300 &deg / C.

The further developments in nanotechnology in last few years provide usage of nanoscale particles for many applications in various areas such as electronics, pharmaceutical, and biomedical due to their strengthened mechanical, thermal and electrical properties. Boron nitride nanotubes are a good example of nanoparticles. In this study, boron nitride nanotubes were successfully synthesized from the reaction of ammonia gas with mixture of boron and iron oxide. Physical and structural properties of the synthesized materials were determined by X-Ray Diffraction, Energy Dispersive X-Ray Spectroscopy, nitrogen sorption, X-Ray Photoelectron Spectroscopy, Fourier Transform Infrared Spectroscopy, and Scanning Electron Microscopy. Experiments were conducted in a tubular furnace at different temperatures and also at different weight ratios of boron to iron oxide. Qualitative chemical analysis of the reactor effluent stream was carried out using a mass spectrometer. The mass spectrometer analysis of the reaction products proved formation of nitrogen in addition to hydrogen and water during the reaction of ammonia gas with the mixture of boron and iron oxide. XRD results showed that hexagonal and rhombohedral boron nitrides and cubic iron were the solid phases formed in the product. FTIR and XPS results also indicated the presence of boron nitride and the atomic ratio of boron to nitrogen was compatible with the chemical stoichiometric relation between boron and nitrogen. It was observed that the crystanility of the product increased with an increase in temperature. The diameter of the produced nanotubes varied from 64 nm to 136 nm. The synthesized nanotubes exhibited Type II isotherms. The surface areas of the produced boron nitride nanotubes decreased with a decrease in both temperature and the weight ratio of boron to iron oxide. The best temperature and weight ratio of boron to iron oxide to produce boron nitride nanotubes were found to be 1300&deg / C and 20, respectively.

Boron nitride nanotubes (BNNTs), firstly synthesized in 1995, are structural analogues of carbon nanotubes (CNTs) with alternating boron and nitrogen atoms instead of carbon atoms. Besides their structure, mechanical and thermal properties of BNNTs are very similar to the remarkable properties of CNTs. However, BNNTs have higher resistance to oxidation than CNTs. Also, BNNTs are electrically isolating. Therefore, they are envisioned as suitable fillers for the fabrication of mechanically and thermally enhanced polymeric composites, while preserving the electrical isolation of the polymer matrix. In this study, polypropylene (PP) &ndash / boron nitride nanotube (BNNT) composites were prepared using a twin-screw extruder. Mechanical and thermal properties of PP&ndash / BNNT composites were investigated as a function of nanotube loading. The nanotubes used in the composites were synthesized from the reaction of ammonia gas with a powder mixture of elemental boron and iron oxide. X-ray diffraction (XRD) analysis revealed the predominant hexagonal boron nitride in the synthesized product. Multi-wall nanotubes with outer diameters ranging from 40 to 130 nm were observed with SEM and TEM analyses. Tensile testing of PP&ndash / BNNT composites revealed slight increases in the Young&rsquo / s modulus and yield strength of neat PP with 0.5 and 1 wt% of the as-synthesized BNNT additions. On the other hand, due to the agglomeration of BNNTs, elongation at break and tensile strength values of composites decreased with increasing nanotube content. In the case of using 0.5 wt% loading of purified and then surface modified BNNTs, slight improvement in all mechanical properties of neat PP was achieved. Differential scanning calorimetry (DSC) analysis revealed a noticeable increase in the crystallization temperature of BNNT&ndash / added composites. Coefficient of linear thermal expansion (CLTE) of polymeric composites were studied and no significant change in the CLTE of neat PP was observed with the addition of BNNTs. Results of thermal gravimetric analysis (TGA) indicated improvements in the thermal stability of neat PP with BNNT additions.

The major objective of this thesis is to systematically investigate the effect of hexagonal BN (h-BN) islands on electronic and vibrational properties of single wall carbon Nanotubes. All our investigation are based on first principle Density Functional Theory (DFT) calculations. Our study is motivated by interesting metal-semiconductor transition recently found in periodically patterned graphene with h-BN islands. After reproducing the electronic band structure for pristine single wall zigzag carbon nanotubes (which shows metallic or semiconducting properties depending on their chirality), we investigated their electronic band structure in the presence of h-BN islands. The band structure depends not only on the defect concentration, but also on the pattern of the defect atoms. Our results also suggest that, if we start with a metallic /semiconducting mixture of ZSWCNTs, upon h-BN addition, the sample converts to fully semiconducting. This is a promising result for applications of CNTs in molecular electronics. Fundamental understanding of vibrational properties of nano electronics component is equally important in their applications especially in thermal management and thermoelectric applications. Defect engineering is one of the potential approach for tuning nanoelectronic devices for optimal thermal management and thermoelectric devices. In this work, I present a systematic investigation on how the group velocity and frequency of different phonon modes depend on various h-BN defect concentrations and defect patterns in ZSWCNTs. The study was extended to investigate the effect of hexagonal-C defects on the electronic and vibrational properties of zigzag single wall Boron Nitride nanotubes (ZSWBNNTs).

No description available.

Glasses and ceramics offer several unique characteristics over polymers or metals. However, they suffer from a shortcoming due to their brittle nature, falling short in terms of fracture toughness and mechanical strength. The aim of this work is to reinforce borosilicate glass matrix with reinforcements to increase the fracture toughness and strength of the glass. Boron nitride nanomaterials, i.e. nanotubes and nanosheets have been used as possible reinforcements for the borosilicate glass matrix. The tasks of the thesis are many fold which include: 1. Reinforcement of commercially derived and morphologically different (bamboo like and cylinder like) boron nitride nanotubes in borosilicate glass with the concentration of 0 wt%, 2.5 wt% and 5 wt% by ball milling process. Same process was repeated with reinforcing cleaned boron nitride nanotubes (after acid purification) into the borosilicate glass with similar concentrations. 2. Production of boron nitride nanosheets using liquid exfoliation technique to produce high quality and high aspect ratio nanosheets. These boron nitride nanosheets were reinforced in the borosilicate glass matrix with concentrations of 0 wt%, 2.5 wt% and 5 wt% by ball milling process. The samples were consolidated using spark plasma sintering. These composites were studied in details in terms of material analysis like thermo-gravimetric analysis, detailed scanning electron microscopy and transmission electron microscopy for the quality of reinforcements etc.; microstructure analysis which include the detailed study of the composite powder samples, the densities of bulk composite samples etc; mechanical properties which include fracture toughness, flexural strength, micro-hardness, Young’s modulus etc. and; tribological properties like scratch resistance and wear resistance. Cleaning process of boron nitride nanotubes lead to reduction in the Fe content (present in boron nitride nanotubes during their production as a catalyst) by ~54%. This leads to an improvement of ~30% of fracture toughness measured by chevron notch technique for 5 wt% boron nitride nanotubes reinforced borosilicate glass. It also contributed to the improvement of scratch resistance by ~26% for the 5 wt% boron nitride nanotubes reinforced borosilicate glass matrix. On the other hand, boron nitride nanosheets were successfully produced using liquid exfoliation technique with average length was ~0.5 µm and thickness of the nanosheets was between 4-30 layers. It accounted to an improvement of ~45% for both fracture toughness and flexural strength by reinforcing 5 wt% of boron nitride nanosheets. The wear rates reduced by ~3 times while the coefficient of friction was reduced by ~23% for 5 wt% boron nitride nanosheets reinforcements. Resulting improvements in fracture toughness and flexural strength in the composite materials were observed due to high interfacial bonding between the boron nitride nanomaterials and borosilicate glass matrix resulting in efficient load transfer. Several toughening and strengthening mechanisms like crack bridging, crack deflection and significant pull-out were observed in the matrix. It was also observed that the 2D reinforcement served as more promising candidate for reinforcements compared to 1D reinforcements. It was due to several geometrical advantages like high surface area, rougher surface morphology, and better hindrance in two dimensions rather than just one dimension in nanotubes.