The elimination of natural organic matter (NOM) is an important aim of water treatment in demineralisation plants of power stations. NOM is regarded as corrosion risk factor in the steam water cycle because of its potential to decompose into low-molecular-weight (LMW) acids and carbon dioxide. Further, the removal of NOM is also one of the main objectives in the drinking water production, since it can cause i) colour, taste and odour problems, ii) formation of carcinogen halogenated disinfection by-products (DBPs) after disinfection with chlorine and iii) bacterial growth in the water distribution system. In earlier studies, it was found that anion exchange is a successful method to remove NOM fractions. However, NOM fractions with low charge density (LMW neutrals and hydrophobic organic carbon (HOC)) and/or large molecular size (biopolymers and particulate organic carbon (POC)) could not be removed in some cases in satisfying quantities. The aim of the present work was to investigate the uptake performance of different anion exchange resins (AERs) in regard to problematic NOM fractions. The AERs differ especially in their functional groups (tertiary versus quaternary amines) and matrix material (polystyrene versus polyacrylic resins). The use of different AERs provides an option to identify possible interactions between adsorbate (NOM fractions) and adsorber (AERs) as well as the mechanism which determine the removal efficiency. The NOM fraction adsorption onto AERs was studied in equilibrium and fixed-bed experiments with three types of starch with different molecular size distributions (model substances for biopolymer fraction) as well as 2-naphthol (model substance for the LMW neutral fraction) at acidic pH (relevant for water in demineralisation plants of power stations) and neutral pH (covering most raw waters). Furthermore, the NOM fraction uptake from “real” acidic and neutral water samples, obtained from a demineralisation plant of a power station, was estimated for different AERs. Results were discussed in terms of size-exclusion, anion exchange and hydrophilic/hydrophobic repulsion. In case that size-exclusion influences the NOM uptake onto AERs, it was found that the smaller the size of the NOM molecules and the higher the water content of the AERs, the more effective the uptake is. Thus, for the removal of biopolymers and POC, polyacrylic resins with high water content could be a good choice. Contrary, polystyrene AERs are the most effective resins in the removal of NOM fractions, if no size-exclusion occurs. They seem to be able to uptake more hydrophilic NOM fractions by polar/ionic interactions between acids/acidic components and tertiary/quaternary amines as well as to remove more hydrophobic NOM fractions by π-π stacking and/or hydrophobic interactions on the polystyrene matrix. Further, it was found that the higher the total volume (anion exchange) capacity of an AER, the higher its NOM removal by polar/ionic interactions can be. At acidic pH, weak/medium base AERs have higher total volume (anion exchange) capacities than strong base AERs, whereas, at neutral pH, strong base AERs have the highest ones. In view of these results, the application of polyacrylic AERs with high water content can be recommended to remove NOM components with large molecular size in demineralisation and drinking water plants. If there is a higher amount of smaller NOM fractions, especially LMW neutrals, than polystyrene weak/medium base AERs should be favoured in demineralisation plants and polystyrene strong base AERs in drinking water treatment plants. From the engineering point of view, breakthrough curve (BTC) prediction models are important for the design of fixed-bed filter. Therefore, two different BTC model approaches were tested in the present study to describe the single-solute adsorption onto AERs: i) the homogenous surface diffusion model (HSDM) with linear driving force (LDF) approach for surface diffusion, known from activated carbon adsorption, and ii) the Glueckauf/Helfferich formulae as an extension of the height equivalent to a theoretical plate (HETP) model, initially used to describe ion exchange processes. It was found that the Glueckauf/Helfferich approach is not only a suitable tool for the fast calculation of BTCs for ionic components, but it can also successfully be applied, after considering the Freundlich model for the mass balance, for the rapid prediction of BTCs for single-solute organic molecules. For competitive BTC predictions, the ideal adsorbed solution theory (IAST) within the LDF model was applied. All calculated BTCs fit the experimental data in a good manner. Thus, the investigated BTC models can be applied for estimating the breakthrough bed volumes of different AERs to avoid leakage of NOM in the drinking or demineralised water caused by overloading. / Die Entfernung von natürlichen organischen Substanzen (NOM) ist ein wichtiges Ziel für die Herstellung von Reinstwasser im Kraftwerksbetrieb, da diese sich im Wasser/Dampf-Kreislauf zu niedermolekularen Säuren und Kohlenstoffdioxid zersetzen können und so ein potentielles Korrosionsrisiko darstellen. Außerdem ist die Elimination von natürlichen organischen Substanzen einer der Schwerpunkte in der Trinkwasseraufbereitung, da NOM im Trinkwasser folgende Konsequenzen verursachen können i) Farb-, Geschmacks- und Geruchsprobleme, ii) Bildung von kanzerogen halogenierten Desinfektionsnebenprodukten nach der Desinfektion mit Chlor und iii) Bakterienwachstum im Wasserverteilungssystem. In früheren Untersuchungen wurde festgestellt, dass Anionenaustauscherharze (AERs) die NOM-Fraktionen in der Regel erfolgreich aufnehmen können. Nur NOM-Fraktionen mit geringer Ladungsdichte (niedermolekulare Neutralstoffe und hydrophober organischer Kohlenstoff) und/oder großer Molekülgröße (Biopolymere und partikulärer organischer Kohlenstoff) können unter bestimmten Bedingungen nicht in zufriedenstellender Menge entfernt werden. Ziel dieser Arbeit war es, das Aufnahmeverhalten unterschiedlicher AERs hinsichtlich problematischer NOM-Fraktionen zu untersuchen. Die AERs unterscheiden sich vor allem in ihren funktionellen Gruppen (tertiäre versus quaternäre Amine) und ihrer Matrix (Polystyren- versus Polyacryl-Harze). Die Verwendung unterschiedlicher AERs erlaubt es, mögliche Wechselwirkungen zwischen Adsorbat (NOM-Fraktionen) und Adsorber (AERs) und die Mechanismen, die die NOM-Aufnahme entscheidend bestimmen, zu identifizieren. Die Entfernung von NOM-Fraktionen durch AERs wurde in Gleichgewichts- und Festbett-versuchen mittels dreier Stärketypen mit unterschiedlicher Molekülgrößenverteilung (Modellsubstanzen für die Biopolymere) und 2-Naphthol (Modellsubstanz für die Neutralstoffe) unter sauren pH-Bedingungen (relevant für die Herstellung von Reinstwasser im Kraftwerksbetrieb) und neutralen pH-Bedingungen (bedeutsam für die meisten Rohwässer) untersucht. Außerdem sollte das Adsorptionsverhalten von AERs bezüglich verschiedener NOM-Fraktionen unter Einsatz von „real“ neutralen und sauren Wasserproben aus einer Wasseraufbereitungsanlage eines Kraftwerksbetriebes eingeschätzt werden. In dieser Arbeit konnte gezeigt werden, dass falls Größenausschluss die NOM-Aufnahme von AERs beeinflusst, dann ist die Adsorption der NOM-Fraktionen umso größer, je kleiner die NOM-Moleküle sind und je höher der Wassergehalt der AERs ist. Daher kann für die Entfernung von größeren Biopolymeren, der Einsatz von AERs mit Polyacryl-Matrix und hohem Wassergehalt die beste Option sein. AERs mit Polystyren-Matrix besitzen die höchste Aufnahmekapazität für NOM-Fraktionen, falls kein Größenausschluss auftritt. Es scheint für sie möglich zu sein, sowohl hydrophile NOM-Fraktionen durch polare/ionische Wechselwirkungen zwischen NOM Säuren/sauren Komponenten und tertiären/quaternären Aminen aufzunehmen als auch hydrophobe NOM-Fraktionen durch π-π Anziehungen und/oder hydrophobe Interaktionen an die Polystyren-Matrix zu binden. Weiterhin konnte gezeigt werden, dass je höher die Gesamtvolumenkapazität eines AERs, desto größer ist die NOM-Entfernung auf Grund von polaren/ionischen Wechselwirkungen. Es gilt, dass schwach/mittel basische AERs im Vergleich zu stark basischen AERs höhere Gesamtvolumenkapazitäten unter sauren pH-Bedingungen besitzen und stark basische AERs die höchsten Gesamtvolumenkapazitäten unter neutralen pH-Bedingungen aufweisen. Auf Grund dieser Ergebnisse ist es möglich, die Verwendung von AERs mit Polyacryl-Matrix und hohem Wassergehalt für die Entfernung von NOM-Fraktionen mit großer Molekülgröße in Reinst- und Trinkwasseraufbereitungsanlagen zu empfehlen. Falls es einen höheren Anteil von kleineren NOM-Fraktionen, im Besonderen Neutralstoffen, gibt, sollte die Verwendung von schwach/mittel basischen AERs in Vollentsalzungsanlagen von Kraft-werksbetrieben und stark basischen AERs in Trinkwasseraufbereitungsanlagen bevorzugt werden. Vor allem im Hinblick auf technische Anwendungen ist es wichtig, Durchbruchskurven (BTC) vorausberechnen zu können. In der vorliegenden Arbeit wurden zwei Modellansätze für die Berechnung von BTCs für die Einkomponentenadsorption getestet: i) das homogene Oberflächendiffusionsmodell mit linearer Triebkraft (LDF), bekannt aus Untersuchungen zur Aufnahme von NOM an Aktivkohle, und ii) die Glueckauf/Helfferich-Formeln, primär verwendet für die Beschreibung von Ionenaustauschprozessen. Es konnte gezeigt werden, dass das Glueckauf/Helfferich-Verfahren nicht nur ein geeignetes Instrument für die schnelle Berechnung von BTCs für ionische Komponenten ist, sondern dass dieses, nach Berücksichtigung des Freundlich-Ansatzes in der Massenbilanz, auch erfolgreich angewendet werden kann, um BTCs für Einkomponentenadsorption von Organika zu berechnen. Für die Vorausberechnung von BTCs für Mehrkomponentensysteme wurde die Theorie der idealen adsorbierten Lösung im LDF-Modell genutzt. Die berechneten BTCs stimmen in guter Qualität mit den experimentell ermittelten BTCs überein. Die Ergebnisse verdeutlichen, dass die untersuchten BTC-Modelle eingesetzt werden können, um Durchbruchspunkte für die jeweiligen AERs zu bestimmen und damit die Gefahr des Schlupfes von NOM ins Trink- bzw. Reinstwasser zu minimieren.

No description available.

No description available.

Increased water- and fertilizer-use-efficiency in containerized crop production, via reduced water loss, enhances crop-available nutrients while reducing non-point source agrichemical contributions in accordance with regulatory standards. Previous studies detailed nutrient leaching patterns throughout crop production seasons, leaving little known about water and dissolved nutrient (solute) movement through soilless substrates during irrigation. The following experiments evaluated fundamental water and solute transport principles through pine-bark based substrates. 1) Ilex crenata Thunb. 'Bennett's Compactum' were grown in 2.7 L containers. Tensiometers detected wetting front (WF) movement throughout the substrate during irrigation. 2) Tracer solution (containing NO3-, PO43- and K+) and deionized water (DI) were applied to substrate-filled columns to characterize tracer breakthrough under saturated and unsaturated conditions. 3) Controlled-release fertilizer (CRF) was topdressed (surface-applied), incorporated (throughout substrate), dibbled (center of substrate) or not applied to fallow substrate, irrigated with DI and leachate analyzed to determine nutrient concentrations throughout irrigation. Tensiometers revealed that seasonal root growth affected substrate pre-irrigation moisture distribution. Wetting fronts channeled through the substrate before becoming thoroughly wetted. Tracer breakthrough occurred with less effluent volume under unsaturated conditions. Breakthrough of NO3- and PO43- was relatively conservative, though 37% of K+ was retained by the substrate. Leachate concentrations for topdressed and incorporated CRF peaked early (first 50mL effluent) before diminishing with continued leaching. Leachate concentrations for dibbled CRF initially increased (first 150mL leachate), plateaued and then diminished. These results show the relative rapidity which water and solutes move through pine-bark during irrigation and demonstrate methods for future research on within-irrigation solute transport. / Master of Science

Atualmente, o tipo de propelente para produtos em aerossol mais usado no mundo é uma mistura de hidrocarbonetos leves (butano e propano - sendo o primeiro em maior proporção). Parte de seu processo de produção é a dessulfurização do butano líquido, através de adsorção em leito fixo usando peneiras moleculares 13X. A literatura científica não apresenta muitas publicações sobre o tema e considerando que a técnica de adsorção é fortemente dependente de dados experimentais para seu maior entendimento, é objetivo deste trabalho estudar este processo através do equilíbrio de adsorção, das curvas de ruptura e do desenvolvimento de um modelo matemático que represente o funcionamento de uma coluna de adsorção de leito fixo a temperatura constante. Obtiveram-se dados sobre o equilíbrio de adsorção por meio de ensaios em banho finito comparando-se a interação de diferentes compostos de enxofre com a peneira molecular 13X e o efeito da temperatura. Utilizou-se a técnica de cromatografia gasosa como método analítico para obtenção dos teores de compostos sulfurados e de hidrocarbonetos. O modelo de Langmuir apresentou bom ajuste aos dados experimentais. Avaliando-se a interação dos componentes sulfurados com a zeólita 13X, identificou-se diferenças significativas, sendo a maior em ordem decrescente: etil-mercaptana, n-propil-mercaptana e terc-butil-mercaptana, respectivamente. A dinâmica do processo de adsorção foi estudada através da obtenção das curvas de ruptura em leitos em escala laboratorial e piloto. Avaliaram-se as influências da variação da concentração de entrada da n-propil-mercaptana e da velocidade do fluido em leito fixo recheado com zeólitas 13X, mantendo os demais parâmetros constantes. Conforme esperado o aumento da concentração inicial reduz o tempo de ruptura, aumenta a quantidade total adsorvida pelo leito e não altera o comportamento da zona de transferência de massa (ZTM). Analisando-se a elevação da velocidade, nota-se também uma diminuição no tempo de ruptura e um aumento da ZTM. O modelo matemático apresentado considera os balanços de massa microscópicos aplicados ao leito, os fenômenos de transporte de massa com modelo de dispersão axial e transporte por convecção da fase líquida para a superfície da partícula e as isotermas de adsorção. As equações diferenciais parciais resultantes foram adimensionalizadas e resolvidas empregando-se o método de diferenças finitas, implementado por código Matlab®. A partir da simulação matemática das condições experimentais obtiveram-se os parâmetros de dispersão axial e de transferência de massa que possibilitaram uma boa reprodução do tempo de ruptura quanto do perfil da zona de transferência de massa para os experimentos em escala laboratorial e piloto. / Currently, the kind of propellant for aerosol products most widely used in the world is a blend of light hydrocarbons (butane and propane - the first in greater proportion). Part of the production of propellant is the desulfurization of liquid-phase butane by molecular sieves 13X in a fixed bed. The scientific literature concerning the adsorption of the mercaptans using zeolite are scarce and considering that the adsorption technique is strongly dependent on experimental data for its better knowlegde, the aim of this work was to study this process by adsorption equilibrium, the breakthrough curves and the development of a mathematic model, simulation and comparison with the operation of a fixed-bed pilot and laboratory-scale column. Adsorption equilibrium parameters were obtained using finite bath experiment and comparing the interaction of different sulfur compounds with molecular sieve 13X and the temperature effect. It was used the gas chromatography as an analytical method in order to obtain the levels of hydrocarbons and sulfur compounds. The Langmuir model well fit the experimental data. Significant differences were identified in the interaction of the sulfur components with zeolite 13X. The major interactions of the sulfur components are in decreasing order: ethyl-mercaptan, n-propyl-mercaptan and terc-butyl-mercaptan. The dynamic of the adsorption process was studied by obtaining the breakthrough curves in laboratory and pilot scale. It was investigated the influence of the initial concentration of n-propyl mercaptan and the fluid velocity in a fixed bed packed with zeolite 13X keeping the other parameters constant. As it was expected, as the inlet sulfur concentration increases the break point time decrease, and enhances the total amount adsorbed by the bed. Analyzing the increase in velocity on the breakthroug profile, it was noted that also decreases the break point time and causes a greater decline of the curve resulting in greater ZTM and anticipating the bed saturation time. The model equations account the mass balance applied in the flowing liquid phase in the column, transport phenomena as the effect of axial dispersion and convection from liquid phase to the adsorbent surface and adsorption isotherm. Finite difference method was used to solve the dimensionless general partial differential equations and it was implemented by Matlab® software. From mathematical simulation of experimental conditions it were obtained the axial dispersion parameters and mass transfer coefficient which allowed a fair agreement in predicting break point time and the mass transfer zone profile.

La protection à long terme des ressources en eau souterraine implique détudier le comportement de leau et des éventuels contaminants quelle véhicule depuis lentrée dans le milieu souterrain (recharge) jusquà lexutoire naturel (émergence, cours deau) ou forcé (pompage) de la nappe. Au cours de ce transit, de nombreux phénomènes dorigine physique ou chimique sont susceptibles daffecter la mobilité et les concentrations du ou des contaminants. Il sagit donc de tenir compte du pouvoir atténuateur, retardateur, voire auto-épurateur du milieu souterrain à leur égard, les conséquences pouvant être positives (dispersion, dilution, dégradation du contaminant) ou négatives (difficultés de reprise du contaminant, impact à long terme de la contamination, ). Lobjectif de cette recherche est de développer une approche conceptuelle et mathématique visant à létude in situ et à la modélisation de la mobilité et du piégeage temporaire ou définitif des solutés au sein du milieu souterrain variablement saturé en eau. Une classification des processus physico-chimiques influençant la mobilité des solutés est proposée, reposant sur trois critères : (1) un distinction entre processus « microscopiques », ayant cours à léchelle de quelques pores et processus « macroscopiques », ayant cours à léchelle du terrain ; (2) une distinction entre processus physiques (affectant tout type de contaminant, indépendamment de sa nature chimique) et processus chimiques (affectant certains contaminants, en fonction de leurs propriétés chimiques spécifiques) ; (3) une distinction entre processus à léquilibre (indépendant du temps) et processus cinétiques (dépendant explicitement du temps). Sur base de cette analyse, le modèle conceptuel considéré comporte trois éléments principaux : ladvection, la dispersion hydrodynamique et un processus de stockage-déstockage de soluté au sein dune phase immobile liquide (effet deau immobile) ou solide (sorption cinétique), représenté par une équation de transfert de premier ordre. Suivant le schéma conceptuel, les adaptations et développements réalisés au sein du code éléments finis SUFT3D, en vue de permettre la simulation du comportement dun soluté dans le milieu souterrain variablement saturé, sont décrits. La détermination des paramètres gouvernant les processus de migration et de piégeage des solutés repose sur linterprétation dessais de traçage réalisés in situ, en milieu saturé et non saturé. Une part importante de la recherche a donc été consacrée à lamélioration des techniques de traçage et dinterprétation des résultats en termes dévolution de la concentration et dévolution de la masse restituée du traceur, cette dernière étant plus adaptée à lévaluation et à la quantification des effets de retard. En vue de représenter de manière plus physique et plus précise linjection dun traceur, une nouvelle approche conceptuelle, mathématique et numérique est élaborée, considérant explicitement les interactions puits aquifère. A laide de ce modèle, divers tests numériques démontrent limpact des conditions dinjection du traceur sur les résultats de traçage, pouvant potentiellement conduire à des erreurs dinterprétation en termes didentification des processus agissant et de quantification des paramètres calibrés. En vue dune interprétation correcte des résultats de traçage, le contrôle des conditions dinjection est donc primordial. Deux études expérimentales servent de base et dillustration aux développements réalisés. Une campagne dessais de traçage en milieu saturé a été réalisée dans la plaine alluviale de la Meuse, à Hermalle-sous-Argenteau. Ces essais permettent de valider et dillustrer lapproche développée en vue de représenter précisément linjection des traceurs et les interactions puits aquifère, de mettre en évidence une série de problèmes conceptuels et pratiques rencontrés lors de la réalisation des essais de traçage, dexaminer le comportement chimique de plusieurs traceurs artificiels et de mettre en évidence les propriétés hydrodispersives des formations alluviales. La deuxième étude a eu pour objectif détudier les mécanismes de migration de substances dissoutes au sein de la zone non saturée surmontant la nappe aquifère des craies en Hesbaye. Les résultats de ces tests permettent de proposer une approche unifiée visant à représenter le comportement hydrodynamique et hydrodispersif des craies fissurées sous des conditions variables de recharge, donc de saturation en eau. Cette étude permet également de mettre en évidence le lien entre les propriétés physiques et hydrodynamiques des limons éoliens en Hesbaye.

[Truncated abstract] Self-filtration is here defined as particle detachment and re-deposition causing re-arrangement of the particles and therefore pore space which affects water flow in soil by decreasing hydraulic conductivity. This is of particular important in soils which are susceptible to structural breakdown. The objective of this thesis was to examine the dynamics of the self-filtration process in sodic sandy soils as affected by ionic strength and soil solution composition. The temporal changes of hydraulic conductivity and the elution of fine particles from soil columns were used as the main criteria to assess selffiltration. Two porous media exhibiting significantly different structural cohesion were examined, one a loamy sand (Balkuling soil) from agricultural land use and the second a mining residue from mineral sands operations . . . The effects of the composition of mixed calcium (Ca) and sodium (Na) ions in solution (sodium adsorption ratio (SAR)) on the exchange behaviour and saturated hydraulic conductivity were examined by carrying out batch binary exchange and saturated column transport experiments. A strong preference for Ca2+ ions in the exchange complex was observed for both soils. Generally K/Ko was found to decrease with increasing sodium adsorption ratio with the more structured Balkuling soil maintaining K/Ko for SARs 3 and 5 at an electrolyte concentration of 100 mmol/L. However measurements at the critical threshold and turbidity concentrations at a SAR of 15 revealed structural breakdown of the pore matrix system attributed to various extents of slaking, swelling, dispersion and decreases of pore radii as a result of selffiltration during leaching. These experiments illustrate the wide range of complex interactions involving clay mineralogy, solution composition and structural factors which can influence the extent of mobilization, transport and re-deposition of colloidal particles during the leaching process in soil profiles.

Atualmente, o tipo de propelente para produtos em aerossol mais usado no mundo é uma mistura de hidrocarbonetos leves (butano e propano - sendo o primeiro em maior proporção). Parte de seu processo de produção é a dessulfurização do butano líquido, através de adsorção em leito fixo usando peneiras moleculares 13X. A literatura científica não apresenta muitas publicações sobre o tema e considerando que a técnica de adsorção é fortemente dependente de dados experimentais para seu maior entendimento, é objetivo deste trabalho estudar este processo através do equilíbrio de adsorção, das curvas de ruptura e do desenvolvimento de um modelo matemático que represente o funcionamento de uma coluna de adsorção de leito fixo a temperatura constante. Obtiveram-se dados sobre o equilíbrio de adsorção por meio de ensaios em banho finito comparando-se a interação de diferentes compostos de enxofre com a peneira molecular 13X e o efeito da temperatura. Utilizou-se a técnica de cromatografia gasosa como método analítico para obtenção dos teores de compostos sulfurados e de hidrocarbonetos. O modelo de Langmuir apresentou bom ajuste aos dados experimentais. Avaliando-se a interação dos componentes sulfurados com a zeólita 13X, identificou-se diferenças significativas, sendo a maior em ordem decrescente: etil-mercaptana, n-propil-mercaptana e terc-butil-mercaptana, respectivamente. A dinâmica do processo de adsorção foi estudada através da obtenção das curvas de ruptura em leitos em escala laboratorial e piloto. Avaliaram-se as influências da variação da concentração de entrada da n-propil-mercaptana e da velocidade do fluido em leito fixo recheado com zeólitas 13X, mantendo os demais parâmetros constantes. Conforme esperado o aumento da concentração inicial reduz o tempo de ruptura, aumenta a quantidade total adsorvida pelo leito e não altera o comportamento da zona de transferência de massa (ZTM). Analisando-se a elevação da velocidade, nota-se também uma diminuição no tempo de ruptura e um aumento da ZTM. O modelo matemático apresentado considera os balanços de massa microscópicos aplicados ao leito, os fenômenos de transporte de massa com modelo de dispersão axial e transporte por convecção da fase líquida para a superfície da partícula e as isotermas de adsorção. As equações diferenciais parciais resultantes foram adimensionalizadas e resolvidas empregando-se o método de diferenças finitas, implementado por código Matlab®. A partir da simulação matemática das condições experimentais obtiveram-se os parâmetros de dispersão axial e de transferência de massa que possibilitaram uma boa reprodução do tempo de ruptura quanto do perfil da zona de transferência de massa para os experimentos em escala laboratorial e piloto. / Currently, the kind of propellant for aerosol products most widely used in the world is a blend of light hydrocarbons (butane and propane - the first in greater proportion). Part of the production of propellant is the desulfurization of liquid-phase butane by molecular sieves 13X in a fixed bed. The scientific literature concerning the adsorption of the mercaptans using zeolite are scarce and considering that the adsorption technique is strongly dependent on experimental data for its better knowlegde, the aim of this work was to study this process by adsorption equilibrium, the breakthrough curves and the development of a mathematic model, simulation and comparison with the operation of a fixed-bed pilot and laboratory-scale column. Adsorption equilibrium parameters were obtained using finite bath experiment and comparing the interaction of different sulfur compounds with molecular sieve 13X and the temperature effect. It was used the gas chromatography as an analytical method in order to obtain the levels of hydrocarbons and sulfur compounds. The Langmuir model well fit the experimental data. Significant differences were identified in the interaction of the sulfur components with zeolite 13X. The major interactions of the sulfur components are in decreasing order: ethyl-mercaptan, n-propyl-mercaptan and terc-butyl-mercaptan. The dynamic of the adsorption process was studied by obtaining the breakthrough curves in laboratory and pilot scale. It was investigated the influence of the initial concentration of n-propyl mercaptan and the fluid velocity in a fixed bed packed with zeolite 13X keeping the other parameters constant. As it was expected, as the inlet sulfur concentration increases the break point time decrease, and enhances the total amount adsorbed by the bed. Analyzing the increase in velocity on the breakthroug profile, it was noted that also decreases the break point time and causes a greater decline of the curve resulting in greater ZTM and anticipating the bed saturation time. The model equations account the mass balance applied in the flowing liquid phase in the column, transport phenomena as the effect of axial dispersion and convection from liquid phase to the adsorbent surface and adsorption isotherm. Finite difference method was used to solve the dimensionless general partial differential equations and it was implemented by Matlab® software. From mathematical simulation of experimental conditions it were obtained the axial dispersion parameters and mass transfer coefficient which allowed a fair agreement in predicting break point time and the mass transfer zone profile.

La chromatographie membranaire est une alternative à la chromatographie classique sur résine basée sur le transport convectif des solutés à travers une membrane microporeuse plutôt que par le transport diffusif des solutés dans les particules de résines. Cette technique présente les avantages de diminuer les phénomènes de diffusion, de réduire les temps de séjour et les pertes de charge, et de permettre la purification rapide de quantités importantes de molécules. La chromatographie membranaire connaît un fort succès commercial. Une gamme importante de membranes chromatographiques mettant en jeu différents mécanismes de rétention (échange d’ions, affinité, etc.) et différentes géométries (feuille, spirale, etc.) est actuellement commercialisée. Malgré ce succès, différents aspects relatifs à la chromatographie membranaire restent mal connus. Cette thèse de doctorat se propose de répondre à certaines questions relatives à cette technique / Membrane chromatography (MC) is an alternative to traditional resin packed columns chromatography. The solute mass transport in the membrane occurs in convective through-pores rather than in stagnant fluid inside the pores of the resins particles, which is limited by the slow diffusive transport. MC offers the main advantage of reducing diffusion phenomena, shorter residence time and lowered pressures drops, and thus, facilitates rapid purification of large quantities of molecules. A wide range of chromatographic membranes involving different molecules retention mechanisms (ion exchange, affinity, etc...) is now commercialized. Despite their success, the influence of the geometry of the membrane chromatography devices remains relatively unexplored from a theoretical point of view. This doctoral thesis is aimed to clarify some ambiguous points related to this technique

<div>Adsorbent technology is widely used in many industrial applications including waste heat recovery, water purification, and atmospheric revitalization in confined habitations. Astronauts depend on adsorbent-based systems to remove metabolic carbon dioxide (CO₂) from the cabin atmosphere; as NASA prepares for the journey to Mars, engineers are redesigning the adsorbent-based system for reduced weight and optimal efficiency. These efforts hinge upon the development of accurate, predictive models, as simulations are increasingly relied upon to save cost and time over the traditional design-build-test approach. Engineers rely on simplified models to reduce computational cost and enable parametric optimizations. Amongst these simplified models is the axially dispersed plug-flow model for predicting the adsorbate concentration during flow through an adsorbent bed. This model is ubiquitously used in designing fixed-bed adsorption systems. The current work aims to improve the accuracy of the axially dispersed plug-flow model because of its wide-spread use. This dissertation identifies the critical model inputs that drive the overall uncertainty in important output quantities then systematically improves the measurement and prediction of these input parameters. Limitations of the axially dispersed plug-flow model are also discussed, and recommendations made for identifying failure of the plug-flow assumption.</div><div><br></div><div>An uncertainty and sensitivity analysis of an axially disperse plug-flow model is first presented. Upper and lower uncertainty bounds for each of the model inputs are found by comparing empirical correlations against experimental data from the literature. Model uncertainty is then investigated by independently varying each model input between its individual upper and lower uncertainty bounds then observing the relative change in predicted effluent concentration and temperature (<i>e.g.</i>, breakthrough time, bed capacity, and effluent temperature). This analysis showed that the LDF mass transfer coefficient is the largest source of uncertainty. Furthermore, the uncertainty analysis reveals that ignoring the effect of wall-channeling on apparent axial dispersion can cause significant error in the predicted breakthrough times of small-diameter beds.</div><div><br></div><div>In addition to LDF mass transfer coefficient and axial-dispersion, equilibrium isotherms are known to be strong lever arms and a potentially dominant source of model error. As such, detailed analysis of the equilibrium adsorption isotherms for zeolite 13X was conducted to improve the fidelity of CO₂ and H₂O on equilibrium isotherms compared to extant data. These two adsorbent/adsorbate pairs are of great interest as NASA plans to use zeolite 13X in the next generation atmospheric revitalization system. Equilibrium isotherms describe a sorbent’s maximum capacity at a given temperature and adsorbate (<i>e.g.</i>, CO₂ or H₂O) partial pressure. New isotherm data from NASA Ames Research Center and NASA Marshall Space Flight Center for CO₂ and H₂O adsorption on zeolite 13X are presented. These measurements were carefully collected to eliminate sources of bias in previous data from the literature, where incomplete activation resulted in a reduced capacity. Several models are fit to the new equilibrium isotherm data and recommendations of the best model fit are made. The best-fit isotherm models from this analysis are used in all subsequent modeling efforts discussed in this dissertation.</div><div><br></div><div>The last two chapters examine the limitations of the axially disperse plug-flow model for predicting breakthrough in confined geometries. When a bed of pellets is confined in a rigid container, packing heterogeneities near the wall lead to faster flow around the periphery of the bed (<i>i.e.</i>, wall channeling). Wall-channeling effects have long been considered negligible for beds which hold more than 20 pellets across; however, the present work shows that neglecting wall-channeling effects on dispersion can yield significant errors in model predictions. There is a fundamental gap in understanding the mechanisms which control wall-channeling driven dispersion. Furthermore, there is currently no way to predict wall channeling effects a priori or even to identify what systems will be impacted by it. This dissertation aims to fill this gap using both experimental measurements and simulations to identify mechanisms which cause the plug-flow assumption to fail.</div><div><br></div><div>First, experimental evidence of wall-channeling in beds, even at large bed-to-pellet diameter ratios (<i>d</i>_bed/<i>d</i>_p=48) is presented. These experiments are then used to validate a method for accurately extracting mass transfer coefficients from data affected by significant wall channeling. The relative magnitudes of wall-channeling effects are shown to be a function of the adsorption/adsorbate pair and geometric confinement (<i>i.e.</i>, bed size). Ultimately, the axially disperse plug-flow model fails to capture the physics of breakthrough when nonplug-flow conditions prevail in the bed.</div><div><br></div><div>The final chapter of this dissertation develops a two-dimensional (2-D) adsorption model to examine the interplay of wall-channeling and adsorption kinetics and the adsorbent equilibrium capacity on breakthrough in confined geometries. The 2-D model incorporates the effect of radial variations in porosity on the velocity profile and is shown to accurately capture the effect of wall-channeling on adsorption behavior. The 2-D model is validated against experimental data, and then used to investigate whether capacity or adsorption kinetics cause certain adsorbates to exhibit more significant radial variations in concentration compared than others. This work explains channeling effects can vary for different adsorbate and/or adsorbent pairs—even under otherwise identical conditions—and highlights the importance of considering adsorption kinetics in addition to the traditional <i>d</i>_bed/<i>d</i>_p criteria.</div><div><br></div><div>This dissertation investigates key gaps in our understanding of fixed-bed adsorption. It will deliver insight into how these missing pieces impact the accuracy of predictive models and provide a means for reconciling these errors. The culmination of this work will be an accurate, predictive model that assists in the simulation-based design of the next-generation atmospheric revitalization system for humans’ journey to Mars.</div>