This master thesis deals with the development and construction of the inverted pendulum, inspired by the Cubli project. The objective is to develop and design an inverted pendulum, in the shape of one side of the cube balancing at one of its corner and for balancing is used the flywheel. For its design 3D printing is used to the maximum extent and as the electronic parts commonly available components at an affordable price are used. The design of the construction and the components allow the construction of a complete cube, without the need of further development or fundamental changes in the design of the model. For the calculations and the design of the controller the Matlab / Simulink software was used. As the controller algorithm the LQR algorithm is used with added integral feedback, to minimize control error. The 3D models of the single parts are created with FreeCAD software and printed on a 3D Prusa i3 MK2S printer.

Hail storms, with hail commonly near 50 mm in diameter that travel with storm wind sabove 25 m/s, cause damages of a large magnitude throughout the globe, with places like USA, Australia and India suffering the greatest. These damages have serious consequences, not least telecommunication products mounted in exposed places. Hail robustness is therefore important to test throughout a product development process, to reduce faulty products and maintenance costs. This thesis includes test rig concepts for hail impact testing and focuses on one final concept. The thesis includes a simulation model of the hail impact test rig, together with a physical implementation of the rig for comparison and validation. Additional experiments and statistical analysis is included to conclude on the accuracy and consistency with respect to realistic hail cases. The result shows that the simulation corresponds to the test rig. This physical implementation of the test rig is consistent and accurate for average sized hail projectiles, however varies more for hail projectiles corresponding to more severe storms. / Hagelstormar, med hagel omkring 50 mm i diameter och en vindhastighet på over 25 m/s, orsakar stora skador över hela världen, där USA, Australien och Indien är några av de mest utsatta platserna. Skadorna har stor påverkan, inte minst telecomprodukterna som är monterade på utsatta platser. Därav är det viktigt att testa produkter mot hagelkollisioner under produktutvecklingsprocessen, för att reducera antalet skadade produkter och kostnader. Detta examensarbete innehåller olika koncept på testriggar som simulerar hagel, med fokus på ett slutgiltigt koncept. Rapporten innehåller en simuleringsmodell av testriggen, samt en fysisk implementering av den för jämförelse och validering. Ytterliggare experiment och statistisk analys innefattas för att kunna dra slutsatser om riggens nogrannhetoch konsekventhet i föhållande till realistiska hagelstormar. Resultatet visar att simuleringen motsvarar testriggens beteende, vilket är önskvärt. Den fysiska implementationen av riggen ger ett noggrant och konsekvent resultat för medelstora hagelprojektiler, däremot fås större variationer för hagelprojektiler som förekommer i  starkare stormar.

Les véhicules de demain, (2020), devront diminuer leurs émissions globales de CO2 de 30% selon les directives européennes. Une solution qui apparait aujourd’hui comme inévitable est la substitution des métaux présents dans les châssis de véhicules par des matériaux composites plus légers et tout aussi performants. Pour généraliser cette approche à tout le secteur automobile, un temps court de fabrication des pièces est exigé pour satisfaire les cadences de production allant jusqu’à 1000 véhicules par jour. La production automatisée et robotisée de ces matériaux, basée sur la technologie de photo-polymérisation au moyen de rayonnements UV, répond à ces exigences. Le procédé de fabrication élaboré se décompose en deux phases : une phase de fabrication automatisée de pré-imprégnés (prépregs), produits semi-finis, et une phase de mise en forme et d’obtention du produit final (composite UV). La première étape consiste en l’imprégnation d’un renfort fibreux sec par une résine liquide photo-polymérisable, puis l’irradiation de celle-ci par des rayonnements UV, de manière à ce que la résine ne soit pas totalement polymérisée. On obtient alors un prépreg collant. La seconde étape de fabrication impose que les pré-imprégnés soient conditionnés parfaitement sous forme de bobines pour qu’ils soient intégrés dans un dispositif robotisé de dépose. D’où la nécessité de concevoir et de réaliser une machine automatisée de production des pré-imprégnés (objet de cette thèse). Cette machine a nécessité une automatisation se caractérisant par l'utilisation d'outils d'instrumentation et de pilotage modernes (servomoteurs Brushless, IHM, capteurs, …). Les essais réalisés sur cette machine ont permis de réaliser des premiers prépregs, dont les résultats ont conduit à des pistes de réflexion pour approfondir l'automatisation de la machine en vue d'améliorer le procédé de fabrication de ces prépregs. / The overall CO2 emission of the future vehicles, (2020), must be reduced by 30%, according to European directives. A solution that seems inevitable nowadays is the substitution of metals present in the vehicle chassis by lighter and equally efficient composite-materials. To generalize this approach throughout the automotive sector, a short manufacturing time of these materials is required to meet the high required production rates, of up to 1000 vehicles per day. The automated and robotic production of these materials, depending on the photo polymerization technology by UV radiation, meets these requirements. The developed automated manufacturing process consists of two phases: the phase of automated manufacturing of semi-finished composite (prepreg), and the phase of shaping and obtaining the final composite (UV composite). The first phase depends on the impregnation of fibrous reinforcement with a photo-polymerizable and liquid resin, then, on the partial irradiation of impregnated reinforcement with UV rays, in such a way that the resin is not completely cured. Thereby, a tacky prepreg is obtained. The second phase of automated manufacturing process requires that the prepregs must be perfectly reeled up in a form of coils, so that they can be incorporated in a robotic lay-up placement head. Hence, the need to design and produce a machine of automated prepreg production (subject of this thesis) is absolutely necessary. This machine requires automation, characterized by the use of modern instrumentations and control tools (Brushless Servo, Human–computer interface HCI, sensors...). The tests performed by this machine have enabled the production of the first prepregs, of which the results led to further approaches to develop the automation of this machine in order to improve the prepregs manufacturing process.

The master thesis encompasses the possibilities of position evaluation and drive control with the aid of SMI work enviroment. Furthermore the thesis is directed to create a program through a designed control algorithm. The work is realised on the elevator model with electronically commuted motor. An incremental scanner is used as the position sensor. The motor control unit is set up and programmed in the SmartMotorInterface software. In the next part, measurements with altered parameters are conducted. On the basis of these measurements the influence of parameters on the positioning process and its accuracy is evaluated. At the conclusion of the work, a design of laboratory task for educational purposes is created. The laboratory task is composed in such a way, that students would become familiar with the SMI work enviroment and would be able to practicaly test the setup of incremental position sensor and motor control with the aid of entered algorithm.