Control of moisture and heat flow through building enclosure assemblies is a critical component of overall building performance. This thesis shows that significant drying of moisture in wall assemblies is possible and that ventilation of cladding significantly increases the rate of drying in some assemblies without having detrimental impact on the enclosures thermal performance. A review found that thermal and moisture buoyancy, wind pressure gradients and mechanical equipment drive ventilation airflow. This ventilation flow can theoretically increase the effective water vapour permeance and thermal conductivity. Ventilation has the potential to increase outward drying through relatively impermeable claddings at the low flows expected to occur in service. The impact on thermal conductance is much less. A methodology for assessing the complicated airflow resistance characteristics of lap sidings was developed and applied to a representative vinyl siding. Field drying studies showed that the sample tested is well ventilated. Field brick veneer clad wall samples were also tested for system airflow resistance over a range of driving pressures. Theoretical predictions under-estimated the measured flow rate for given steady driving air pressures. Measurements of naturally driven cavity air speeds and smoke pencil testing showed that flow rates were commonly occurring that would in theory significantly affect the hygrothermal performance of the walls. This was confirmed with field drying studies. A field drying study of east-facing test wall with vinyl siding and brick veneer cladding was conducted in Waterloo, Ontario, Canada. Significant amounts of drying and inward moisture redistribution were measured. Wall sheathing dried quickly in hot summer conditions but in some cases significant inward driven moisture flow occurred. In cool and cold weather the wall dried more slowly and much less moisture moved inward. Increased cladding ventilation significantly increased drying rates and reduced internal wall assembly moisture levels. It was concluded that cladding ventilation acts to increase the effective vapour permeance of cladding and to reduce solar driven inward vapour drives. The use of spun bonded polyolefin sheathing membrane in lieu of #15 asphalt impregnated felt was found to improved hygrothermal performance in the test walls. The difference observed was concluded to be due to the higher vapour permeance of the spun bonded polyolefin and may not hold for wall assemblies with lower permeance sheathings (e. g. oriented strand board and foam plastic). Walls clad with vinyl siding dried faster than those clad with brick veneer. It was concluded that the vinyl siding is a well ventilated cladding system.

Much of the existing commercial building stock is aging and will be in need of upgrades now or within the next twenty years. Typically, enclosure retrofits consist of adding insulation to the exterior or interior of the existing façade. In this thesis, an alternative solution is examined, whereby a glass façade is added to the exterior of the existing building, forming a double façade. For historic buildings, this could preserve and protect the existing façade without completely covering it up. For outdated buildings, this could modernize the existing façade, giving it the all-glazed appearance that is currently so popular among architects. Regardless of the retrofit motive, it is important to be able to quantitatively compare retrofit solutions to make informed design decisions. As such, building simulation can be an important design tool. At present, there is no available simulation tool that can easily and accurately model a double façade; therefore, a double façade (DoFa) model was developed to fill this gap. A spreadsheet-based, lumped model was created and validated using current complex fenestration models and limited experimental data. Further experimental data is required to validate all aspects of the model. Results showed that the DoFa model can achieve accurate results; however, further development is needed to predict optical properties of venetian blinds and convective coefficients for natural airflow in double façade cavities. The model was used to compare double façades to traditional glazing systems. Results indicated that double façades can perform comparably to double glazing with outdoor shading in summer, and triple glazing in winter. However, the results are only valid for the tested glazing systems. In a second application, the DoFa model was modified to simulate an entire enclosure to compare a double façade retrofit to more traditional retrofit strategies. Results suggested that a double façade provides a good improvement in winter performance, though summer overheating is a concern. For the case study examined, a double façade would have performed better than the chosen retrofit of replacing the windows with double glazing and indoor shading, without insulating the opaque components. The DoFa model can be very useful in creating double façade preliminary design and operation strategies. At present, the DoFa model is an instantaneous, stand-alone tool. Further development is needed to pair the DoFa model with whole building energy simulations.

Control of moisture and heat flow through building enclosure assemblies is a critical component of overall building performance. This thesis shows that significant drying of moisture in wall assemblies is possible and that ventilation of cladding significantly increases the rate of drying in some assemblies without having detrimental impact on the enclosures thermal performance. A review found that thermal and moisture buoyancy, wind pressure gradients and mechanical equipment drive ventilation airflow. This ventilation flow can theoretically increase the effective water vapour permeance and thermal conductivity. Ventilation has the potential to increase outward drying through relatively impermeable claddings at the low flows expected to occur in service. The impact on thermal conductance is much less. A methodology for assessing the complicated airflow resistance characteristics of lap sidings was developed and applied to a representative vinyl siding. Field drying studies showed that the sample tested is well ventilated. Field brick veneer clad wall samples were also tested for system airflow resistance over a range of driving pressures. Theoretical predictions under-estimated the measured flow rate for given steady driving air pressures. Measurements of naturally driven cavity air speeds and smoke pencil testing showed that flow rates were commonly occurring that would in theory significantly affect the hygrothermal performance of the walls. This was confirmed with field drying studies. A field drying study of east-facing test wall with vinyl siding and brick veneer cladding was conducted in Waterloo, Ontario, Canada. Significant amounts of drying and inward moisture redistribution were measured. Wall sheathing dried quickly in hot summer conditions but in some cases significant inward driven moisture flow occurred. In cool and cold weather the wall dried more slowly and much less moisture moved inward. Increased cladding ventilation significantly increased drying rates and reduced internal wall assembly moisture levels. It was concluded that cladding ventilation acts to increase the effective vapour permeance of cladding and to reduce solar driven inward vapour drives. The use of spun bonded polyolefin sheathing membrane in lieu of #15 asphalt impregnated felt was found to improved hygrothermal performance in the test walls. The difference observed was concluded to be due to the higher vapour permeance of the spun bonded polyolefin and may not hold for wall assemblies with lower permeance sheathings (e. g. oriented strand board and foam plastic). Walls clad with vinyl siding dried faster than those clad with brick veneer. It was concluded that the vinyl siding is a well ventilated cladding system.

Much of the existing commercial building stock is aging and will be in need of upgrades now or within the next twenty years. Typically, enclosure retrofits consist of adding insulation to the exterior or interior of the existing façade. In this thesis, an alternative solution is examined, whereby a glass façade is added to the exterior of the existing building, forming a double façade. For historic buildings, this could preserve and protect the existing façade without completely covering it up. For outdated buildings, this could modernize the existing façade, giving it the all-glazed appearance that is currently so popular among architects. Regardless of the retrofit motive, it is important to be able to quantitatively compare retrofit solutions to make informed design decisions. As such, building simulation can be an important design tool. At present, there is no available simulation tool that can easily and accurately model a double façade; therefore, a double façade (DoFa) model was developed to fill this gap. A spreadsheet-based, lumped model was created and validated using current complex fenestration models and limited experimental data. Further experimental data is required to validate all aspects of the model. Results showed that the DoFa model can achieve accurate results; however, further development is needed to predict optical properties of venetian blinds and convective coefficients for natural airflow in double façade cavities. The model was used to compare double façades to traditional glazing systems. Results indicated that double façades can perform comparably to double glazing with outdoor shading in summer, and triple glazing in winter. However, the results are only valid for the tested glazing systems. In a second application, the DoFa model was modified to simulate an entire enclosure to compare a double façade retrofit to more traditional retrofit strategies. Results suggested that a double façade provides a good improvement in winter performance, though summer overheating is a concern. For the case study examined, a double façade would have performed better than the chosen retrofit of replacing the windows with double glazing and indoor shading, without insulating the opaque components. The DoFa model can be very useful in creating double façade preliminary design and operation strategies. At present, the DoFa model is an instantaneous, stand-alone tool. Further development is needed to pair the DoFa model with whole building energy simulations.

A large portion of the existing building stock in North America is comprised of post-World War II high-rise apartment buildings, particularly in the Greater Golden Horseshoe in Ontario. They are home to a large portion of the Canadian population. These buildings are nearly 50 years old and reaching the end of their useful lifespan. Significant deterioration has lead to life safety concerns, poor standards of living, and aesthetic degradation. They also consume a significant amount of energy resulting in contributing to Canada’s high per capita greenhouse gas emissions. This thesis investigates the impact of various retrofit strategies on the energy consumption, durability, and occupant comfort of the towers. The building enclosure is the primary focus. The impacts were analyzed using three approaches. Whole building energy consumption was simulated by adapting a spreadsheet based Building Energy and Loads Analysis (BELA) model, originally intended for office buildings. Heat flow and temperatures across the enclosures were modeled using a two-dimensional finite element model (Therm 5.2). A single, theoretical building dubbed the, “Archetype”, was developed to define the characteristics of a “typical” tower using details extracted from four sets of drawings for towers built in Toronto during the late 1960s. Various quantities and configurations of thermal insulation were added to the Archetype and the resulting effective thermal resistances were modeled. Adding insulation to the interior significantly reduces the effectiveness of any added thermal resistance. Insulating on the exterior allows the insulation around the balconies to reach 80% of its rated value, even without insulating the balconies. Energy efficiency measures (EEMs) including retrofitting the walls, windows, appliances, or HVAC equipment were simulated and it was found that each on its own did not have a major impact on annual energy consumption. Packages of EEMs were created and simulated. It was found that a basic and high-performance whole building retrofit packages would save approximately 40% and 55% of the annual energy consumption, respectively, based on the Archetype. An analysis and discussion of the enclosure retrofit impacts on freeze-thaw potential, interior surface and interstitial condensation, occupants’ thermal comfort, and passive thermal comfort was completed. An interior versus exterior enclosure retrofit comparison summary illustrated that an exterior enclosure retrofit has significant benefits relative to an interior retrofit including ease of construction, greater durability, and improved comfort. The difference in annual energy reduction between an interior and exterior enclosure retrofit was small.

A large portion of the existing building stock in North America is comprised of post-World War II high-rise apartment buildings, particularly in the Greater Golden Horseshoe in Ontario. They are home to a large portion of the Canadian population. These buildings are nearly 50 years old and reaching the end of their useful lifespan. Significant deterioration has lead to life safety concerns, poor standards of living, and aesthetic degradation. They also consume a significant amount of energy resulting in contributing to Canada’s high per capita greenhouse gas emissions. This thesis investigates the impact of various retrofit strategies on the energy consumption, durability, and occupant comfort of the towers. The building enclosure is the primary focus. The impacts were analyzed using three approaches. Whole building energy consumption was simulated by adapting a spreadsheet based Building Energy and Loads Analysis (BELA) model, originally intended for office buildings. Heat flow and temperatures across the enclosures were modeled using a two-dimensional finite element model (Therm 5.2). A single, theoretical building dubbed the, “Archetype”, was developed to define the characteristics of a “typical” tower using details extracted from four sets of drawings for towers built in Toronto during the late 1960s. Various quantities and configurations of thermal insulation were added to the Archetype and the resulting effective thermal resistances were modeled. Adding insulation to the interior significantly reduces the effectiveness of any added thermal resistance. Insulating on the exterior allows the insulation around the balconies to reach 80% of its rated value, even without insulating the balconies. Energy efficiency measures (EEMs) including retrofitting the walls, windows, appliances, or HVAC equipment were simulated and it was found that each on its own did not have a major impact on annual energy consumption. Packages of EEMs were created and simulated. It was found that a basic and high-performance whole building retrofit packages would save approximately 40% and 55% of the annual energy consumption, respectively, based on the Archetype. An analysis and discussion of the enclosure retrofit impacts on freeze-thaw potential, interior surface and interstitial condensation, occupants’ thermal comfort, and passive thermal comfort was completed. An interior versus exterior enclosure retrofit comparison summary illustrated that an exterior enclosure retrofit has significant benefits relative to an interior retrofit including ease of construction, greater durability, and improved comfort. The difference in annual energy reduction between an interior and exterior enclosure retrofit was small.

Climate change is exacerbating natural disasters, and extreme weather events increase with intensity and frequency. This requires an in-depth evaluation of locations across the various U.S. climates where natural hazards, vulnerabilities, and potentially damaging impacts will vary. At the local building level within the built environment, private residences are crucial shelter systems to protect against natural disasters, and are a central component in the greater effort of creating comprehensive disaster resilient environments. In light of recent disasters such as Superstorm Sandy, there is an increased awareness that residential buildings and communities need to become more resilient for the changing climates they are located in, or will face devastating consequences. There is a great potential for specific high-performance building technologies to play a vital role in achieving disaster resilience on a local scale. The application of these technologies can not only provide immediate protection and reduced risk for buildings and its occupants, but can additionally alleviate disaster recovery stressors to critical infrastructure and livelihoods by absorbing, adapting, and rapidly recovering from extreme weather events, all while simultaneously promoting sustainable building development. However, few have evaluated the link between residential high-performance building technologies and natural disaster resilience in regards to identifying and prioritizing viable technologies to assist decision-makers with effective implementation. This research developed a framework for a process that prioritizes residential building technologies that encompass both high-performance and resilience qualities that can be implemented for a variety of housing contexts to mitigate risks associated with climate induced natural hazards. Decision-makers can utilize this process to evaluate a residential building for natural disaster risks, and communicate strategies to improve building performance and resilience in response to such risks. / Ph. D.

Recently, buildings have been receiving more serious attention to help reduce global energy consumption. At the same time, thermal comfort has become an increasing concern for building occupants. Phase Change Materials (PCMs), which are capable of storing and releasing significant amounts of energy by melting and solidifying at a given temperature, are perceived as a promising opportunity for improving the thermal performance of buildings. This is because they use their thermophysical properties and latent heat while transforming state (or phase) as a feature for thermal energy storage systems to reduce overall energy demand, specifically during peaks hours, as well as to improve thermal comfort in buildings. This research aims to provide an overview of opportunities and challenges for the utilization of PCMs in the Architecture, Engineering, and Construction (AEC) sector, a broader understanding of specifically promising technologies, and a clarification of the effectiveness of different applications in building enclosures design especially in exterior walls. The research discusses how PCMs can be incorporated within building enclosures effectively to enhance building performance and improve thermal comfort while reducing heating and cooling energy consumption in buildings. The major objectives of the research include studying the properties of PCMs and their potential impact on building construction, clarifying PCMs selection criteria for building application, identifying the effectiveness of utilizing PCMs on saving energy, and evaluating the contribution of utilizing PCMs in building enclosures to thermal comfort. The research uses an exploratory quantitative approach that contains three main stages: 1) a systematic literature review, 2) laboratory experiments, and 3) validation to meet the goal of the research. Finally, by extrapolating results, the research ends with a practical assessment of application opportunities and how to effectively utilize PCMs in exterior walls of buildings. / PHD

The Intergovernmental Panel on Climate Change (IPCC) estimates that buildings account for 40% of the global energy use. The IPCC believes substantial improvements to building efficiency can be implemented easily by improving building enclosures through increased levels of insulation, optimizing glazing areas and minimizing infiltration of outside air.<br><br> Building enclosure design encompasses a wide range of parameters but the transport of heat, air and moisture through the enclosure is of primary importance. In predominantly cold Canadian climates, adequate thermal insulation, effective air barriers, and proper moisture control are crucial for energy savings and durability of the structure.<br><br> For decades, standard construction practice in Canada dictated a polyethylene sheet behind the interior drywall layer to serve as a vapour barrier for assemblies with traditional fibre-based cavity insulation. If the polyethylene sheet was sealed carefully enough it had the added benefit of reducing air leakage. Unfortunately, vapour barriers place the emphasis on the wrong moisture transport mechanism; air leakage can have 10 times or greater the wetting potential than vapour diffusion. Regardless, code enforcement personnel continued (and continue in some areas) to require vapour barriers in all climates, all assemblies, and all occupancies. To do so, they overrule the provision in Part 5 of The National Building Code of Canada that states vapour barriers are not required if it can be shown that the uncontrolled vapour diffusion will not affect the operation of the building and systems, or the health and safety of the occupants.<br><br> Foam plastic insulations perform better than fibre-based insulation in terms of the combined resistance to transmission of heat, air and vapour. This research investigated several types of open cell and closed cell spray polyurethane foam insulation in a variety of assembly configurations both in lab tests and hygrothermal simulations. The simulations were extrapolated to seven Canadian climate categories and three levels of interior relative humidity. The goal was to determine which spray polyurethane foam applications required the addition of a dedicated vapour barrier layer beyond what the foam itself could provide.<br><br> The moisture content of the oriented strand board sheathing layer (OSB) in the tested and modelled assemblies was used as the performance evaluation point because during wintertime vapour drives, the wood sheathing is the most likely condensing surface. Prolonged high moisture content (greater than 20%) in wood and wood products in wall assemblies leads to mould growth and decay. By this measure, if the wood sheathing moisture contents stay within the safe range (less than 19%) a vapour barrier is not necessary. The results are presented in Table 7-4.<br><br> The performance of assemblies containing closed cell spray foam was excellent for all climates and humidity levels. Their performance was equivalent to traditional wall assemblies incorporating a polyethylene sheet vapour barrier. The performance of assemblies with open cell spray foam was equivalent to traditional wall assemblies containing no vapour barrier. Open cell spray foam and fibreglass batt both require additional vapour control layers with all but the mildest Canadian climates with the lowest interior humidities. However, in those mild climates with low interior humidities, the only vapour control layer required was a medium permeance latex paint with primer.<br><br>

The Intergovernmental Panel on Climate Change (IPCC) estimates that buildings account for 40% of the global energy use. The IPCC believes substantial improvements to building efficiency can be implemented easily by improving building enclosures through increased levels of insulation, optimizing glazing areas and minimizing infiltration of outside air.<br><br> Building enclosure design encompasses a wide range of parameters but the transport of heat, air and moisture through the enclosure is of primary importance. In predominantly cold Canadian climates, adequate thermal insulation, effective air barriers, and proper moisture control are crucial for energy savings and durability of the structure.<br><br> For decades, standard construction practice in Canada dictated a polyethylene sheet behind the interior drywall layer to serve as a vapour barrier for assemblies with traditional fibre-based cavity insulation. If the polyethylene sheet was sealed carefully enough it had the added benefit of reducing air leakage. Unfortunately, vapour barriers place the emphasis on the wrong moisture transport mechanism; air leakage can have 10 times or greater the wetting potential than vapour diffusion. Regardless, code enforcement personnel continued (and continue in some areas) to require vapour barriers in all climates, all assemblies, and all occupancies. To do so, they overrule the provision in Part 5 of The National Building Code of Canada that states vapour barriers are not required if it can be shown that the uncontrolled vapour diffusion will not affect the operation of the building and systems, or the health and safety of the occupants.<br><br> Foam plastic insulations perform better than fibre-based insulation in terms of the combined resistance to transmission of heat, air and vapour. This research investigated several types of open cell and closed cell spray polyurethane foam insulation in a variety of assembly configurations both in lab tests and hygrothermal simulations. The simulations were extrapolated to seven Canadian climate categories and three levels of interior relative humidity. The goal was to determine which spray polyurethane foam applications required the addition of a dedicated vapour barrier layer beyond what the foam itself could provide.<br><br> The moisture content of the oriented strand board sheathing layer (OSB) in the tested and modelled assemblies was used as the performance evaluation point because during wintertime vapour drives, the wood sheathing is the most likely condensing surface. Prolonged high moisture content (greater than 20%) in wood and wood products in wall assemblies leads to mould growth and decay. By this measure, if the wood sheathing moisture contents stay within the safe range (less than 19%) a vapour barrier is not necessary. The results are presented in Table 7-4.<br><br> The performance of assemblies containing closed cell spray foam was excellent for all climates and humidity levels. Their performance was equivalent to traditional wall assemblies incorporating a polyethylene sheet vapour barrier. The performance of assemblies with open cell spray foam was equivalent to traditional wall assemblies containing no vapour barrier. Open cell spray foam and fibreglass batt both require additional vapour control layers with all but the mildest Canadian climates with the lowest interior humidities. However, in those mild climates with low interior humidities, the only vapour control layer required was a medium permeance latex paint with primer.<br><br>