Thesis (M.S.)--Virginia Polytechnic Institute and State University, 1992. / Vita. Abstract. Includes bibliographical references (leaves 93-98). Also available via the Internet.

Thesis (M.S. - Civil Engineering and Engineering Mechanics)--University of Arizona, 1986. / Includes bibliographical references (leaves 206-211).

From pharmaceutical powders to agricultural grains, a great proportion of the materials handled in industrial situations are granular or particulate in nature. The variety of stesses that the matierals may experience and the resulting bulk behaviours may be complex. In agricultural engineering, a better understanding into agricultural processes such as seeding, harvesting, transporting and storing will help to improve the handling of agricultural grains with optimised solutions. A detailed understanding of a granular system is crucial when attempting to model a system, whether it is on a micro (particle) or macro (bulk) scale. As numerical capabilities are ever increasing, the Discrete Element Method (DEM) is becoming an increasingly popular numerical technique for computing the behaviour of discrete particels for both industrial and scientific applications. A look into the literature shows a lack of validation of what DEM can predict, specifically with respect to bulk behaviour. In addition, when validation studies are conducted, discrepancies between bulk responses in physical tests and numerical predictions using measured particles properties may arise. The aire of this research is to develop a methodology to calibrate DEM models for agricultural grains using data meaured in bulk physical tests. The methodology will have a wider application to granular solids in general and will advance understanding in the area of DEM model calibration. A contrasting set of granular materials were used to develop the methodology including 3 inorganic solids (single and paired glass beads, and polyethylene terephthalate pellets) and two organic materials (black eyes beans and black kidney beans). The developed methodology consists of three steps: 1. The development of bulk physical tests to measure the bulk responses that will be used to calibrate the DEM models, 2. The creation of the numerical dataset that will describe how the DEM input parameters influence the bulk responses , and 3. The optimisation of the DEM parameters using a searching algorithm and the results from Step 1 and 2. Two laboratory devices were developed to provide calibration data for the proposed methodology: a rotating drum and an confined compression test. These devices were chosen as they can produce bulk responses that are repeatable and easy to quantify, as well as generate discriminating results in numerical simulations when DEM parameters are varied. The bulk response determined from the rotating drum device was the dynamic angle of repose Ør formed when the granular material in a 40% filled drum is rotating at a speed of 7 rpm. the confined compression apparatus was used to determine the bulk stiffness of a system by monitoring the change in void ratio from the stress applied during a loading and unloading cycle. The gradient of the loading and unloadng curves termed λ and κ respectively were chosen as the bulk responses to calibrate the DEM models. The experimental results revealed that the dynamic Ør was significantly influences by the particle aspect ration and boundary conditions. The stiffness parameters were found to be predominantly influences by the initial packing arrangement. The numerical dataset describing how the DEM input parameters influence the numerical bulk responses was created by simulating the bulk physical tests, varying selected DEM parameters and monitoring the effects on bulk parameters. To limit the number of simulations required, design of experiment (DOE) methods were used to determine a reduced factorial matrix of simulations. In additions, an extensive parametric investigation on the non-optimised parameters as well as a scaling sensitivity study was carried out. The final step in determining the optimised parameters is to use a searching algorithm to infer the DEM parameters based on the numerical dataset and used the experimental results as calibration data. To perform a comparative study, tow searching algorithms were explored: the first was a simple method based on Microsoft Excel's Solver algorithm coupled with a weighted inverse distance method. The second made used of the statistical analysis program Statistica. It was shown that the Excel Solver algorithm is simpler and quicker to use but for the present first implementation, could only perform an optimisation based on two bulk responses. Statistica required the creation of a staistical model based on the numerical dataset before using the profiling and desirability searching technique, but was able to optimise the parameter using all three bulk responses. A verification and validation of the optimisation methodology was conducted using the optimised parameters for the black eyed beans. A verification was cnducted by simulating the two calibration experiments using the optimsed parameters and comparing these with the experiments. In addition, a validation was peformed by predicting the response of ta shallow footing penetration on a bed of black eyed beans. It was found that DEM simulations using optimised parameters predicted vertical stress on the footing during penetration to an acceptable degree of accuracy for industrial applications (<10%) at penetration depths up to 30mm.

From June to November 2007, a microscopic analysis was conducted on the activated sludge from eleven selected wastewater treatment plants (WWTP's) belonging to the City of Cape Town. The primary objective was the identification of the dominant and secondary filamentous organisms. Other important criteria included were the floe character, diversity, filament index (Fl) and identification of the protozoan and metazoan communities. The operational data determined from routine analyses of the sludge, influent and effluent were used to assess the relationship of the filamentous population to wastewater characteristics and to compare this with previous findings. Fl values of >3 and dissolved sludge volume indices (DSVI's) of >150 were chosen as representing the possibility of bulking conditions being present. The five most prevalent dominant filaments were Type 0092, Type 1851, actinomycetes, Microthrix parvicella and Type 021N, being present in 74%, 31%, 22%, 17% and 14% of samples respectively. Type 0092 did not appear to be associated with bulking in any of the WWTP's, although it was often incidentally present as a co-dominant species when bulking conditions existed. All three WWTP's with the Modified Ludzack-Ettinger configuration harboured Type 1851 as the major dominant species, irrespective of whether the plants treated domestic or industrial effluent. Conditions suggestive of bulking were present in two of these WWTP's. Contrary to expectations, Type 1851 was often found as a dominant species where domestic waste was the primary influent. Type 021N and actinomycetes were strongly implicated when bulking occurred. The overgrowth of these filaments appeared to be related to factors such as nutrient deficiency (Type 021N) or the presence of large amounts of low molecular weight substances in the influent. Microthrix parvicella did not cause major bulking problems. There was a strong association between low levels of nitrates/nitrites in the clarifier supernatant and good phosphorous removal, irrespective of the configuration of the WWTP. The converse was also true. / Thesis ((M. Environmental Science))--North-West University, Potchefstroom Campus, 2009.

Biopile and landfarming systems are ex situ technologies developed for the remediation of contaminated soils. In this study, laboratory degradation experiments and a combined full-scale landfarming and biopile system were operated for the remediation of diesel fuel-contaminated soils. The effectiveness of bulking agents (wood chips and rice hulls), inorganic nutrients (N and P), and biological agent on petroleum hydrocarbon biodegradation were also evaluated. The ratios of contaminated soils to bulking agents applied in the experiments were 1:0, 3:1, 6:1, and 10:1. The soil to bulking agent ratio of 10.7:1 was applied in the full-scale system. After 93 days of incubation, the highest reduction rate for total petroleum hydrocarbon - diesel (TPHd) removal was observed in the experiment with a soil to bulking agent ratio of 3:1. Results show that TPHd degradation trend followed a typical first-order degradation pattern. The calculated regression coefficient ranged from 0.008 ¡V 0.0129. Results also indicate that the addition of biological agent had a significant enhancement of TPHd removal. Results from the full-scale study show that the average TPHd concentrations from 5,544 mg/kg to 488 mg/kg after 231 days of operation. This implies that approximately 91.2% of TPHd removal was obtained. Field results show that temperature affected biodegradation rates, production of CO2, total hererotrophic bacterial biomass, and TPHd reduction efficiencies. Thus, temperature plays an important role for the operation of is biopile and landfarming systems.

Filamentous bulking is a problem that has long plagued activated sludge (AS) wastewater treatment plants (WWTPs). Much research has looked at its prevention and control but there is still no solution. The sludge microbiological community is very complex and there are many factors that can affect bulking. Clay addition in scaled-down activated sludge systems was investigated at concentrations of 0.4, 2.0 and 5.0 g/L along with sequencing batch reactor (SBR) parameters when run with a synthetic wastewater (SWW). The 5.0g/L concentration exhibited positive results on settling in the form of modified SVI but appeared to cause no reduction in filament length. These preliminary investigations indicate that clay may help improve sludge settling but make no difference in the abundance of filamentous microorganisms. The SBRs exhibited trends in regards to running systems with a synthetic wastewater. A loss of volatile suspended solids (VSS), coupled with increase in sludge volume index (SVI), suggested a link between lack of non-VSS and settling ability. This has implications in the importance of non-VSS such as grit or clay in research performed using SWWs.

From June to November 2007, a microscopic analysis was conducted on the activated sludge from eleven selected wastewater treatment plants (WWTP's) belonging to the City of Cape Town. The primary objective was the identification of the dominant and secondary filamentous organisms. Other important criteria included were the floe character, diversity, filament index (Fl) and identification of the protozoan and metazoan communities. The operational data determined from routine analyses of the sludge, influent and effluent were used to assess the relationship of the filamentous population to wastewater characteristics and to compare this with previous findings. Fl values of >3 and dissolved sludge volume indices (DSVI's) of >150 were chosen as representing the possibility of bulking conditions being present. The five most prevalent dominant filaments were Type 0092, Type 1851, actinomycetes, Microthrix parvicella and Type 021N, being present in 74%, 31%, 22%, 17% and 14% of samples respectively. Type 0092 did not appear to be associated with bulking in any of the WWTP's, although it was often incidentally present as a co-dominant species when bulking conditions existed. All three WWTP's with the Modified Ludzack-Ettinger configuration harboured Type 1851 as the major dominant species, irrespective of whether the plants treated domestic or industrial effluent. Conditions suggestive of bulking were present in two of these WWTP's. Contrary to expectations, Type 1851 was often found as a dominant species where domestic waste was the primary influent. Type 021N and actinomycetes were strongly implicated when bulking occurred. The overgrowth of these filaments appeared to be related to factors such as nutrient deficiency (Type 021N) or the presence of large amounts of low molecular weight substances in the influent. Microthrix parvicella did not cause major bulking problems. There was a strong association between low levels of nitrates/nitrites in the clarifier supernatant and good phosphorous removal, irrespective of the configuration of the WWTP. The converse was also true. / Thesis ((M. Environmental Science))--North-West University, Potchefstroom Campus, 2009.

From June to November 2007, a microscopic analysis was conducted on the activated sludge from eleven selected wastewater treatment plants (WWTP's) belonging to the City of Cape Town. The primary objective was the identification of the dominant and secondary filamentous organisms. Other important criteria included were the floe character, diversity, filament index (Fl) and identification of the protozoan and metazoan communities. The operational data determined from routine analyses of the sludge, influent and effluent were used to assess the relationship of the filamentous population to wastewater characteristics and to compare this with previous findings. Fl values of >3 and dissolved sludge volume indices (DSVI's) of >150 were chosen as representing the possibility of bulking conditions being present. The five most prevalent dominant filaments were Type 0092, Type 1851, actinomycetes, Microthrix parvicella and Type 021N, being present in 74%, 31%, 22%, 17% and 14% of samples respectively. Type 0092 did not appear to be associated with bulking in any of the WWTP's, although it was often incidentally present as a co-dominant species when bulking conditions existed. All three WWTP's with the Modified Ludzack-Ettinger configuration harboured Type 1851 as the major dominant species, irrespective of whether the plants treated domestic or industrial effluent. Conditions suggestive of bulking were present in two of these WWTP's. Contrary to expectations, Type 1851 was often found as a dominant species where domestic waste was the primary influent. Type 021N and actinomycetes were strongly implicated when bulking occurred. The overgrowth of these filaments appeared to be related to factors such as nutrient deficiency (Type 021N) or the presence of large amounts of low molecular weight substances in the influent. Microthrix parvicella did not cause major bulking problems. There was a strong association between low levels of nitrates/nitrites in the clarifier supernatant and good phosphorous removal, irrespective of the configuration of the WWTP. The converse was also true. / Thesis ((M. Environmental Science))--North-West University, Potchefstroom Campus, 2009.

Thesis (PhD (Chemical Engineering))--University of Pretoria, 2008. / Includes bibliographical references (p. 110-126)

Deficiencies in biotreatment due to uncontrolled growth of filamentous microorganisms is a problem for wastewater plants worldwide. The project was assigned with the task of reducing the growth of filamentous bacteria at the paper mill SCA Munksund. 12 bacteria and 1 fungi species were presented to the project as problematic due to their filamentous properties. Operating parameters affecting filamentous growth was examined and presented. The information gathered showed that a decrease in filamentous growth for 5 especially problematic bacteria could possibly be achieved by raising the DO, increasing the concentration of nutrients and decreasing the sludge age. Other parameters affecting the growth of filamentous bacteria, such as pH, temperature and F/M were found to be too diverse among the examined species. Alternative solutions not focused on finding optimal operating parameters was also investigated. Promising results were treatment using a feast-famine approach, installation of an anaerobic selector and ozonation of return sludge. A statistical analysis was also performed on operating data. Methods used were Principal component analysis, Clustering and Logistic regression. These were used as a proof of concept rather than providing meaningful data for an operating window.