This work was carried out to study the effect of shot-peening on the fatigue behaviour of carbon steels. Differently heat treated medium and high carbon steel specimens were selected. Medium carbon steels, AISI 1141 and AISI 1151, were respectively air cooled and quenched-tempered. A high carbon steel, C70S6 (AISI 1070), was air cooled. The other material was a powder metal (0.5% C) steel. Each group of steels was divided into two. One was shot-peened. The other half remained in their original conditions. All were fatigue tested under fully reversed (R=-1) tension-compression loading conditions. Microhardness tests were carried out on both the grip and gage sections of selected non shot-peened and shot-peened specimens to determine the hardness profile and effect of cycling. Shot-peening was found to be deeper on one side of each specimen. Compressive residual stress profiles and surface roughness measurements were provided. Shot-peening increased the surface roughness from 0.26±0.03µm to 3.60±0.44µm. Compressive residual stresses induced by shot-peening reached a maximum of -463.9MPa at a depth of 0.1mm.The fatigue limit (N≈106 cycles) and microhardness profiles of the non shot-peened and shot-peened specimens were compared to determine the material behaviour changes after shot-peening and cycling. Also their fatigue properties were related to the manufacturing process including heat and surface treatments. Comparing the grip and gage microhardness profiles of each steel showed that neither cyclic softening nor hardening occurred in the non shot-peened condition. Cyclic softening was apparent in the shot-peened regions of all steels except powder metal (PM) steel. The amount of softening in the shot-peened region was 55.0% on the left side and 73.0% on the right in the AISI 1141 steel , 46.0% on the left side and 55.0% on the right in the C70S6AC steel and 31.0% on the right side in AISI 1151QT steel. Softening was accompanied by a decrease in the depth of surface hardness. It is suggested that although the beneficial effects of shot peening, compressive residual stresses and work hardening, were offset by surface roughness, crack initiation was more likely to occur below the surface. Surface roughness was not a significant factor in controlling the fatigue lives of AISI 1141AC and C70S6 steels, since they were essentially the same for the non shot-peened and shot-peened conditions. Shot-peening had very little effect on the push-pull fatigue limit of C70S6 steel (-2.1%), and its effect on AISI 1141AC steel was relatively small (6.0%). However, the influence of shot-peening on the AISI 1151QT and PM steels was more apparent. The fatigue limit of the PM steel increased 14.0% whereas the fatigue limit of the AISI 1151QT steel decreased 11.0% on shot peening.

This work was carried out to study the effect of shot-peening on the fatigue behaviour of carbon steels. Differently heat treated medium and high carbon steel specimens were selected. Medium carbon steels, AISI 1141 and AISI 1151, were respectively air cooled and quenched-tempered. A high carbon steel, C70S6 (AISI 1070), was air cooled. The other material was a powder metal (0.5% C) steel. Each group of steels was divided into two. One was shot-peened. The other half remained in their original conditions. All were fatigue tested under fully reversed (R=-1) tension-compression loading conditions. Microhardness tests were carried out on both the grip and gage sections of selected non shot-peened and shot-peened specimens to determine the hardness profile and effect of cycling. Shot-peening was found to be deeper on one side of each specimen. Compressive residual stress profiles and surface roughness measurements were provided. Shot-peening increased the surface roughness from 0.26±0.03µm to 3.60±0.44µm. Compressive residual stresses induced by shot-peening reached a maximum of -463.9MPa at a depth of 0.1mm.The fatigue limit (N≈106 cycles) and microhardness profiles of the non shot-peened and shot-peened specimens were compared to determine the material behaviour changes after shot-peening and cycling. Also their fatigue properties were related to the manufacturing process including heat and surface treatments. Comparing the grip and gage microhardness profiles of each steel showed that neither cyclic softening nor hardening occurred in the non shot-peened condition. Cyclic softening was apparent in the shot-peened regions of all steels except powder metal (PM) steel. The amount of softening in the shot-peened region was 55.0% on the left side and 73.0% on the right in the AISI 1141 steel , 46.0% on the left side and 55.0% on the right in the C70S6AC steel and 31.0% on the right side in AISI 1151QT steel. Softening was accompanied by a decrease in the depth of surface hardness. It is suggested that although the beneficial effects of shot peening, compressive residual stresses and work hardening, were offset by surface roughness, crack initiation was more likely to occur below the surface. Surface roughness was not a significant factor in controlling the fatigue lives of AISI 1141AC and C70S6 steels, since they were essentially the same for the non shot-peened and shot-peened conditions. Shot-peening had very little effect on the push-pull fatigue limit of C70S6 steel (-2.1%), and its effect on AISI 1141AC steel was relatively small (6.0%). However, the influence of shot-peening on the AISI 1151QT and PM steels was more apparent. The fatigue limit of the PM steel increased 14.0% whereas the fatigue limit of the AISI 1151QT steel decreased 11.0% on shot peening.

No description available.

No description available.

Este trabalho comprovou a eficácia do processo de roleteamento profundo no aumento da vida em fadiga em eixos submetidos ao ensaio de fadiga sob tensão axial. Uma pesquisa bibliográfica extensa foi realizada para o entendimento do comportamento físico do fenômeno encruamento, onde esta pesquisa abrangeu a metalurgia, plasticidade e elasticidade dos materiais, processos de geração de tensão residual e ensaios destrutivos e não destrutivos para obtenção de valores reais. O corpo de prova utilizado, em relação ao corpo de prova padronizado, foi modificado para simular o efeito do entalhe como concentrador de tensões. Corpos de prova sem o tratamento mecânico de roleteamento e corpos de prova com o tratamento foram submetidas ao ensaio de fadiga de tensão axial e de difração de raios-X, a fim de comparar o ganho do processo de roleteamento profundo. Com os resultados dos ensaios de fadiga foi possível obter as curvas Wöhler, "S-N", pertinentes aos dois diferentes grupos de amostras: com e sem o tratamento de roleteamento profundo. Simulações pelo Método dos Elementos Finitos foram usadas também para tentar reproduzir os efeitos da tensão residual compressiva sobre a vida em fadiga assim como os resultados obtidos nos ensaios de fadiga e difração de raios-X. / This project has proved the effectiveness of the deep rolling process in the increasing of fatigue life on shafts submitted to axial stress fatigue test. A deep literature research has done for understanding of the physic behavior of the hardening phenomenon, where this research included metallurgy, plasticity and elasticity of materials, generation of residual stress processes and destructive and nondestructive tests to obtain the real values. The specimen used, comparing to the standard one, had been changed to simulate the notch effect as stress concentrator. Specimen with and without rolling mechanical treatment have submitted to axial stress fatigue test and X-rays diffraction test, to compare the gain of the deep rolling process. With the results of fatigue tests, became possible to obtain the Wöhler curves, "S-N", from each different groups of specimens: with and without the deep rolling treatment. Simulations by Finite Element Method have also used to try reproducing the compressive residual stress effects under the fatigue life, like the obtained results from fatigue and X-rays diffraction tests.

O Jateamento com granalha (shot peening, em inglês) é um processo de fabricação amplamente utilizado em indústrias mecânicas, automotivas, navais, aeronáuticas e outras indústrias metalúrgicas. O objetivo principal é induzir tensões residuais de compressão para melhorar a vida à fadiga das peças e estruturas. A modelagem e simulação do processo são muito difíceis, pois envolvem a consideração de muitos e complexos aspectos. Este trabalho propõe um método de modelagem tridimensional utilizando o método dos elementos finitos para a simulação numérica desse processo assim como a sua influência na propagação de trinca, considerando efeitos pouco estudados, como o amolecimento do material devido ao aumento da temperatura na peça durante os impactos, ao comportamento elasto-plástico das granalhas e a rugosidade da peça tratada nos parâmetros da trinca. A modelagem proposta para simular o processo de jateamento com granalhas inclui: (i) análise dinâmica explícita, (ii) modelagem tridimensional, (iii) cálculo da velocidade real das granalhas, (iv) modelo de contato com coeficientes de atrito estático e dinâmico entre as áreas em contato, (v) o modelo constitutivo de Johnson-Cook para o comportamento do material alvo, (vi) um comportamento elasto-plástico multilinear para as granalhas, (vii) a consideração da cobertura real de uma área dada da superfície jateada, (viii) a consideração do aumento da temperatura no material durante o processo e (ix) o relaxamento de tensões residuais devido a este aumento de temperatura. As simulações numérico-computacionais para investigar a influência do processo em fenômenos, tais como fadiga e propagação de trinca, necessitou uma nova abordagem para a incorporação das tensões residuais num modelo de elementos finitos. Além disso, foram realizados vários ensaios quase-estáticos e dinâmicos para a determinação dos parâmetros do modelo constitutivo de Johnson-Cook para o aço AISI 5160. Para a avaliação das metodologias propostas, as tensões residuais foram introduzidas e avaliadas em uma mola parabólica automotiva, sendo que as tensões residuais foram avaliadas através da técnica de difração de raios-X, a intensidade e a cobertura do processo de jateamento com granalha na mola foram avaliadas com Lupa e rugosímetro. Também, dados experimentais de ensaios de fadiga relatados na literatura, realizados em corpos de prova tipo CT foram utilizados. A modelagem numérica do processo de jateamento com granalha desenvolvida neste trabalho consegue prever com sucesso os perfis das tensões residuais, com valores bem próximos aos obtidos experimentalmente. A investigação numérica do efeito do processo na vida à fadiga e fratura das peças comprovou a sua influência nos parâmetros de propagação de trinca nas regiões afetadas pelo processo, ocasionando um amplo aumento da vida à fadiga, e confirmou o relaxamento das tensões residuais devido aos ciclos de carregamento conforme as observações experimentais na literatura. / Shot peening is a manufacturing process widely used in the mechanical, automotive, marine, aeronautical and other metallurgical industries. The main purpose is to induce residual compression stresses to improve fatigue life. The modeling and simulation of the process are very difficult as they involve the consideration of many and complex aspects. This work proposes a three-dimensional modelling method using the finite element method for the numerical simulation of this process as well as its influence on crack propagation, considering little studied effects such as softening of the material due to the increase in temperature in the part during impacts , the elastic-plastic behavior of the shot and the roughness of the treated part in the crack parameters. The proposed modelling approach to simulate the shot peening process includes: (i) explicit dynamic analysis, (ii) three-dimensional modeling, (iii) calculation of the real velocity of the shot, (iv) contact model with static and dynamic friction coefficients between the contact areas, (v) the Johnson-Cook constitutive model for target material behavior, (vi) a multilinear elasto-plastic behavior for the shot, (vii) consideration of real coverage in a given area of the peened surface, (viii) consideration of temperature increase in the material during the process and (ix) relaxation of residual stresses due to this rise in temperature. Numerical-computational simulations to investigate the influence of the shot peening process on phenomena, such as fatigue and crack propagation, required a new approach for the incorporation of residual stress in a finite element model. In addition, several quasi-static and dynamic tests were carried out to determine the parameters of the constitutive Johnson-Cook model for AISI 5160 steel. To assess the proposed methodologies, the residual stresses were introduced and evaluated in an automotive parabolic spring, with the residual stresses being evaluated by the X-ray diffraction technique, the intensity and coverage of the shot peening process for the spring were evaluated with magnifying glass and roughness gauge. Also, fatigue tests available in the literature, carried out on types of CT specimens, were used. The numerical modeling of the shot peening process developed in this work can successfully predict the residual stress profiles, with values close to those obtained experimentally. The numerical investigation of the effect of the process in the fatigue life and fracture of the pieces proved its influence in the parameters of crack propagation in the regions affected by the process, causing a wide increase of the fatigue life, and confirmed the relaxation of the residual stresses due to the cycles loading according to experimental observations in the literature.