Copper oxide nanoparticles (NPs) are used in an expanding range of industries including a potential for agricultural applications as a fungicide. Accidental spills or misapplication of CuO NPs may lead to soil contamination. Plant roots exude a wide range of organic chemicals for bioprotection and to enhance bioavailability of nutrients. Many of these chemicals are metal chelators that may increase the solubility of CuO NPs, thus enhancing the impact of these NPs on plants. This work was directed towards understanding which plant exudates force increased solubility of CuO NPs and to determine if the level of NP in the growth matrix drives a feedback effect, regarding composition and quantity of exudates. Wheat seedlings (Triticum aestivum cv Deloris) were grown in a sand matrix for 10 days after 3 days of germination. The sand was amended with sublethal doses of CuO NPs from 0 to 300 mg Cu/kg dry sand. Sand was selected as the solid growth matrix as a proxy for soil in terms of plant root morphology, mechanical impedance and water stress, while providing a low background of dissolved organic carbon for the isolation of root exudates. After plant growth, the pore water was collected from the sand by vacuum filtration and analyzed. By coupling analytic techniques including Triple Quad Mass Spectroscopy and ion chromatography with geochemical modeling, we have identified citrate and the phytosiderophore, deoxymugineic acid (DMA) as chelators that drove the majority of dissolution of CuO NPs, especially DMA at higher CuO NP doses. Altered biogeochemistry within the rhizosphere was correlated with increased plant uptake of Cu and bio-response via exudate type, quantity and metal uptake. Exposure of wheat to CuO NPs lead to dose-dependent reduction in Fe, Ca, Mg, Mn and K in roots and shoots. This work is relevant to growth of commercially important crop wheat in the presence of CuO NPs as a fertilizer, fungicide or a pollutant.

Optical properties of copper oxide nanoparticles in a silica matrix thin film have been investigated. Films were prepared on Si substrates from a sol-gel by spin coating. Four samples with different thicknesses, from 14,5-109 nm, were fabricated. Optical properties were measured with Variable Angle Spectroscopic Ellipsometry. The aim of the project was to gain further understanding of these films that are interesting in applications for solar absorbers as solar selective coatings. Ellipsometricangles Ψ and Δ were measured in the wavelength range from 250-1700 nm. A dispersion model was developed and fitted to experimental data with acceptable results.

<div>Thermal desalination of high salinity water resources is crucial for increasing freshwater supply, but efficiency enhancements are badly needed. Nanomaterial enhancements and novel condensation regimes offer enormous potential for improving promising technologies like membrane distillation (MD). In this work, we first examined nanofluids for MD, including the role of nanoscale physics, and model system-level energy efficiency enhancements. Our model included the dominant micro-mixing from Brownian motion in fine particle nanofluids (copper oxide) and the unusually high axial conduction from phonon resonance through Van der Waals interaction in carbon nanotube nanofluids. Carbon nanotubes resulted in a consistent, wide range of improvements; while copper oxide particles showcased diminishing returns after a concentration of 0.7%, where Brownian motion effects reduced. However, the enhancements at higher concentrations from liquid layering around nanoparticles were impractical in MD, since the related high surfactant levels compromised the membrane hydrophobicity and promoted fouling. Dilute solutions of metallic nanofluids can be actively integrated to enhance the performance of MD, whereas stronger nanofluid solutions should be limited to heat exchangers that supply thermal energy to MD systems. We then investigated slippery liquid infused porous surfaces (SLIPS) for enhanced condensation rates in MD. Dropwise condensation heat transfer was modelled considering the effects of the departing, minimum droplet radii and the interfacial thermal resistances. Effective droplet shedding from these surfaces led to an experimental thermal efficiency of 95%. Alternatively, porous condensers with superior wicking properties and conductive heat transfer offered a robust solution to high salinity desalination. We modelled the onset of flooding in porous condensers using Darcy’s law for porous media, including the effects of the condenser permeability and determined the optimal condenser thickness at varying system length scales. The increased active area of condensation resulted in a significant enhancement (96.5%) in permeate production and 31.7% improvement in experimental thermal efficiency. However, porous condensers were only compatible with flat plate module designs limiting their practicality.</div>