Anti-resonant hollow core fibre is a new kind of optical fibre waveguide in which light is trapped in a hollow core surrounded by the capillary formed microstructured cladding. This fibre exhibits high damage threshold, low dispersion and ultra-low nonlinearity with relatively low loss of a few tens of dB/km. Its intrinsic feature of multimode delivery limits the applications with high requirements of single mode transmission. In my thesis, I demonstrate how the design of hollow core fibre can be improved with single mode guidance. S2 imaging measurement was used to analyse the mode content of the solid core fibres. In my research, I established S2 measurement to measure the mode contents in hollow core fibres for the first time. Two hollow core fibres with 8 capillaries and 7 capillaries in their claddings were fabricated in same fashion and showed differences in low attenuations. By comparing the mode contents in both of the fibres via S2 imaging measurement, 7-capillary HCF was demonstrated to give better performance on single mode guidance. Among the applications of the HCF, the property of delivering high power in HCF makes the gas filled HCF laser possible. In my research, a continuous-wave mid-infrared acetylene filled hollow core laser was built with a slope efficiency of 33% and an output power of over 1 watt at the wavelength region of 3.1~3.2 μm. The pump source is an Erbium-doped fibre amplified tunable laser diode which works at C-band wavelength. The fibre without the gain medium has two transmission bands with low attenuation of 0.037 dB/m and 0.063 dB/m at pumping and lasing wavelengths respectively. This laser system works in either cavity-based configuration or single pass ASE configuration. The latter configuration shows a better performance in high output power and high slope efficiency. The optimized laser system was studied experimentally with the proper fibre length and gas pressure. This laser system could be extended to be filled with other molecules to longer wavelengths and has potential for high power output.

This thesis presents a method to fabricate a robust optical directional coupler sensor using a solid core fiber (SCF) and a hollow core fiber (HCF). Through evanescent wave coupling mechanism, the optical power is exchanged between SCF and HCF. The hollow core of the HCF can be filled with liquid samples to alter the coupling ratio which imparts change in amount of light propagating through the SCF. Thus, it gives the coupler with ability of sensing refractive index of the sample with good sensitivity of 4.03 ± 0.50 volts per refractive index units (V/RIU) for refractive indices ranging from 1.331 ± 0.003 to 1.403 ± 0.003 with a resolution of 3.5 × 10−3 refractive index units (RIU). The SCF-HCF coupler was also used to sense the temperature based on the concept of temperature dependence on refractive index of the sample inside the hollow core of HCF. Further, the packaging methods are described that protect coupler from ambient environments and improves the life span of sensor. / Graduate

Gas Sensing Has Become a Very Important and Attractive Technique Because of Its Various Applications, Such as in the Increasingly Concerning Case of Environmental Issues, Automobile Emission Detection, Natural Gas Leakage Detection, Etc. It Also Has Significant Applications in Industries, Such as Safety and Health Monitoring in Underground Mines. Among Those Sensing Areas, Fiber-optic Sensors Have Drawn Considerable Attention Because of Its Small Size, Light Weight, High Sensitivity, and Remote Sensing Capability. However, Current Fiber-optic Gas Sensing Techniques Have Several Limitations on Their Potential for Multiplexed or Distributed Sensing Due to Difficulties Such as High Complexity or Large Loss. To Accomplish the Goal for Multiplexed Gas Sensing, an Off-centered Core Fiber Design Is Investigated. The Eccentric Core Can Reduce Attenuation, Keep Mechanical Strength, and Lower Fabrication Cost. To Verify the Feasibility of the Design, Fiber Field Distribution Is First Studied in Simulation, Which Will Be Discussed in Detail in Chapter 2. Then Two Fiber Samples with a Length of 10 Cm and 40 Cm Are Prepared and Placed in a Custom Methane Sensing System for Gas Absorption Testing, Which Is Detailed in Chapter 3. From Etching Analysis, Localized Surface Defects Are Found as the Main Reason for Power Loss. Performance Such as Detection Resolution and Sensitivity Are Investigated. In Chapter 4, Theoretical Evaluations Have Been Conducted for Multiplexed Sensors Performances Using the Off-centered Core Fiber to Study the Impact Fiber Parameters on Sensing System Design. The Conclusion and Summary Are Presented in Chapter 5. / Master of Science / Gas Sensing Has Become a Very Important and Attractive Technique Because of Its Various Applications, Such as in the Increasingly Concerning Case of Environmental Issues, Automobile Emission Detection, Natural Gas Leakage Detection, Etc. It Also Has Significant Applications in Industries, Such as Safety and Health Monitoring in Underground Mines. Among Those Sensing Areas, Fiber-optic Sensors Have Drawn Considerable Attention Because of Its Small Size, Light Weight, High Sensitivity, and Remote Sensing Capability. However, Current Fiber-optic Gas Sensing Techniques Have Several Limitations on Their Potential for Long Distance Distributed Sensing Due to Difficulties Such as High Fabrication Complexity. In This Work, a Fiber-optic Gas Sensor with Special Structure Was Designed. The Sensor Can Reduce Attenuation, Keep Mechanical Strength, and Lower Fabrication Cost. To Verify the Feasibility of the Design, Theory Analysis and Simulation Were Conducted, Which Will Be Discussed in Detail in Chapter 2. Then Two Samples with a Length of 10 Cm and 40 Cm Were Prepared and Placed in a Custom Methane Sensing System for Testing. And Their Performance Such as Sensitivity Is Investigated. In Chapter 4, Theoretical Evaluations Have Been Conducted for Multiplexed Sensors Performances Evaluation to Study the Impact Fiber Parameters on Sensing System Design. The Conclusion and Summary Are Presented in Chapter 5.

付記する学位プログラム名: 京都大学卓越大学院プログラム「先端光・電子デバイス創成学」 / 京都大学 / 新制・課程博士 / 博士(情報学) / 甲第25445号 / 情博第883号 / 新制||情||148(附属図書館) / 京都大学大学院情報学研究科通信情報システム専攻 / (主査)教授 大木 英司, 教授 原田 博司, 教授 岡部 寿男 / 学位規則第4条第1項該当 / Doctor of Informatics / Kyoto University / DFAM

This Masters thesis investigates the ligand–particle binding interactions in the thiol–capped CdTe nanoparticles and dye adsorbed gold nanoparticles. In the CdTe nanoparticles, Raman modes corresponding to the CdTe core, thiol ligand and their interfacial layers were observed and correlated to the different nanoparticle properties. To the best of our knowledge, this is the first time that such strong Raman modes of the thiol-capped nanoparticles in aqueous solution have been reported. In the gold nanoparticle systems, gold–citrate binding interactions were observed as well as adsorption of the Raman dyes and binding with the polyethyleneglycol polymer coating and phospholipid coating. These observations coincided with findings from conventional optical techniques. In addition, gold nanoparticles were found to carbonize at high pump power and prolonged exposure time. In summary, the two nanoparticle characterizations demonstrated the high sensitivity and nondestructive nature of the photonic crystal fiber for Raman spectroscopy.

This Masters thesis investigates the ligand–particle binding interactions in the thiol–capped CdTe nanoparticles and dye adsorbed gold nanoparticles. In the CdTe nanoparticles, Raman modes corresponding to the CdTe core, thiol ligand and their interfacial layers were observed and correlated to the different nanoparticle properties. To the best of our knowledge, this is the first time that such strong Raman modes of the thiol-capped nanoparticles in aqueous solution have been reported. In the gold nanoparticle systems, gold–citrate binding interactions were observed as well as adsorption of the Raman dyes and binding with the polyethyleneglycol polymer coating and phospholipid coating. These observations coincided with findings from conventional optical techniques. In addition, gold nanoparticles were found to carbonize at high pump power and prolonged exposure time. In summary, the two nanoparticle characterizations demonstrated the high sensitivity and nondestructive nature of the photonic crystal fiber for Raman spectroscopy.

In this thesis, we have compared between dual-core fiber coupler with photonic crystal fiber coupler. From Surface Integral Equation Method derived from Maxwell¡¦s equations, we can simulate tapered fiber coupler, dual-core fiber coupler and photonic crystal fiber coupler. By analyzing the propagating characteristics and performance of these couplers, we hope to discuss between their advantages and dis-advantages. We have found that at the same parameters, conventional fiber coupler¡¦s coupling length is roughly half compared to photonic crystal coupler. In terms of bandwidth, photonic crystal coupler aided by air-hole tuning can achieve multiples times larger than conventional fiber coupler. So, we believe that in communication networks with a lust of bandwidth, photonic crystal coupler can definitely live up its expectations.

[ES] A día de hoy, las redes de comunicaciones de fibra óptica están alcanzando su capacidad límite debido al rápido crecimiento de la demanda de datos en la última década, generado por el auge de los teléfonos inteligentes, las tabletas, las redes sociales, la provisión de servicios en la nube, las transmisiones en streaming y las comunicaciones máquina-a-máquina. Con el fin de solventar dicho problema, se ha propuesto incrementar la capacidad límite de las redes ópticas mediante el reemplazo de la fibra óptica clásica por la fibra óptica multinúcleo (MCF, acrónimo en inglés de multi-core fiber), la cual es capaz de integrar la capacidad de varias fibras ópticas clásicas en su estructura ocupando prácticamente la misma sección transversal que éstas. Sin embargo, explotar todo el potencial de una fibra MCF requiere entender en profundidad los fenómenos electromagnéticos que aparecen en este tipo de fibras cuando guiamos luz a travésde ellas. Así pues, en la primera parte de la tesis se analizan teóricamente estos fenómenos electromagnéticos y, posteriormente, se estudia la viabilidad de la tecnología MCF en distintos tipos de redes ópticas de transporte, específicamente, en aquellas que hacen uso de transmisiones radio-sobre-fibra. Estos resultados pueden ser de gran utilidad para las futuras generaciones móviles 5G y Beyond-5G en las próximas décadas. Adicionalmente, con el fin de expandir las funcionalidades básicas de las fibras MCF, esta tesis explora nuevas estrategias de diseño de las mismas utilizando la analogía existente entre las ecuaciones que rigen la mecánica cuántica y el electromagnetismo. Con esta idea en mente, en la segunda parte de la tesis se propone diseñar una nueva clase de fibras MCF usando las matemáticas de la supersimetría, surgida en el seno de la teoría de cuerdas y de la teoría cuántica de campos como un marco teórico de trabajo que permite unificar las interacciones fundamentales de la naturaleza (la nuclear fuerte, la nuclear débil, el electromagnetismo y la gravedad). Girando en torno a esta idea surgen las fibras MCF supersimétricas, las cuales nos permiten procesar la información de los usuarios durante la propia propagación de la luz a través de ellas, reduciendo así la complejidad del procesado de datos del usuario en recepción. Finalmente, esta tesis se completa introduciendo un cambio de paradigma que permite diseñar dispositivos fotónicos disruptivos. Demostramos que la supersimetría de mecánica cuántica no relativista, propuesta como una serie de transformaciones matemáticas restringidas al dominio espacial, se puede extender también al dominio del tiempo, al menos dentro del marco de trabajo de la fotónica. Como resultado de nuestras investigaciones, demostramos que la supersimetría temporal puede convertirse en una plataforma prometedora para la fotónica integrada ya que nos permite diseñar nuevos dispositivos ópticos versátiles y ultra-compactos que pueden jugar un papel clave en los procesadores del futuro. Asimismo, con el fin de hacer los resultados principales de esta tesis doctoral lo más generales posibles, se detalla cómo poder extrapolarlos a otros campos de la física como acústica y mecánica cuántica. / [CA] Avui en dia, les xarxes de comunicacions de fibra òptica estan aconseguint la seua capacitat límit a causa del ràpid creixement de la demanda de dades duante l'última dècada, generat per l'auge dels telèfons intel·ligents, les tablets, les xarxes socials, la provisió de servicis en la núvol, les transmissions en streaming i les comunicacions màquina-a-màquina. Per a resoldre el dit problema, s'ha proposat incrementar la capacitat límit de les xarxes òptiques per mitjà del reemplaçament de la fibra òptica clàssica per la fibra òptica multinúcleo (MCF, acrònim en anglés de multi-core fiber), la qual és capaç d'integrar la capacitat de diverses fibres òptiques clàssiques en la seua estructura ocupant pràcticament la mateixa secció transversal que estes. Tanmateix, explotar tot el potencial d'una fibra MCF requereix entendre en profunditat els fenòmens electromagnètics que apareixen en aquestes fibres quan guiem llum a través d'elles. Així, doncs, en la primera part de la tesi analitzem teòricament aquests fenòmens electromagnètics i, posteriorment, estudiem la viabilitat de la tecnologia MCF en distints tipus de xarxes òptiques de transport, específicament, en aquelles que fan ús de transmissions ràdio-sobre-fibra. Estos resultats poden ser de gran utilitat per a les futures generacions mòbils 5G i Beyond-5G en les pròximes dècades. Addicionalment, a fi d'expandir les funcionalitats bàsiques de les fibres MCF, esta tesi explora noves estratègies de disseny de les mateixes utilitzant l'analogia existent entre les equacions que regixen la mecànica quàntica i l'electromagnetisme. Amb aquesta idea en ment, en la segona part de la tesi proposem dissenyar una nova classe de fibres MCF usant les matemàtiques de la supersimetria, sorgida en el si de la teoria de cordes i de la teoria quàntica de camps com un marc teòric de treball que permet unificar les interaccions fonamentals de la natura (la nuclear forta, la nuclear feble, l'electromagnetisme i la gravetat). Al voltant d'aquesta idea sorgeixen les fibres MCF supersimètriques, les quals ens permeten processar la informació dels usuaris durant la pròpia propagació de la llum a través d'elles, reduint així la complexitat del processament de dades de l'usuari a recepció. Finalment, esta tesi es completa introduint un canvi de paradigma que permet dissenyar dispositius fotónicos disruptius. Demostrem que la supersimetria de mecànica quàntica no relativista, proposta com una sèrie de transformacions matemàtiques restringides al domini espacial, es pot estendre també al domini del temps, almenys dins del marc de treball de la fotónica. Com resultat de les nostres investigacions, demostrem que la supersimetria temporal pot convertir-se en una plataforma prometedora per a la fotònica integrada ja que ens permet dissenyar nous dispositius òptics versàtils i ultracompactes que poden jugar un paper clau en els processadors del futur. Per tal de fer els resultats principals d'aquesta tesi doctoral el més generals possibles, es detalla com poder extrapolar-los a altres camps de la física com ara la acústica i la mecànica quàntica. / [EN] To date, communication networks based on optical fibers are rapidly approaching their capacity limit as a direct consequence of the increment of the data traffic demand in the last decade due to the ubiquity of smartphones, tablets, social networks, cloud computing applications, streaming services including video and gaming, and machine-to-machine communications. In such a scenario, a new class of optical fiber which is able to integrate the capacity of several classical optical fibers approximately in the same transverse section as that of the original one, the multi-core fiber (MCF), has been recently proposed to overcome the capacity limits of current optical networks. However, the possibility of exploiting the full potential of an MCF requires to deeply understand the electromagnetic phenomena that can be observed when guiding light in this optical medium. In this vein, in the first part of this thesis, we analyze theoretically these phenomena and, next, we study the suitability of the MCF technology in optical transport networks using radio-over-fiber transmissions. These findings could be of great utility for 5G and Beyond-5G cellular technology in the next decades. In addition, the close connection between the mathematical framework of quantum mechanics and electromagnetism becomes a great opportunity to explore ground-breaking design strategies of these new fibers that allow us to expand their basic functionalities. Revolving around this idea, in the second part of this thesis we propose to design a new class of MCFs using the mathematics of supersymmetry (SUSY), emerged within the context of string and quantum field theory as a means to unify the basic interactions of nature (strong, electroweak, and gravitational interactions). Interestingly, a supersymmetric MCF will allow us, not only to propagate the light, but also to process the information of users during propagation. Finally, we conclude this thesis by introducing a paradigm shift that allows us to design disruptive optical devices. We demonstrate that the basic ideas of SUSY in non-relativistic quantum mechanics, restricted to the space domain to clarify unsolved questions about SUSY in string and quantum field theory, can also be extended to the time domain, at least within the framework of photonics. In this way, it is shown that temporal supersymmetry may serve as a key tool to judiciously design versatile and ultra-compact optical devices enabling a promising new platform for integrated photonics. For the sake of completeness, we indicate how to extrapolate the main results of this thesis to other fields of physics, such as acoustics and quantum mechanics. / Macho Ortiz, A. (2019). Multi-Core Fiber and Optical Supersymmetry: Theory and Applications [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/124964

The aim of this master’s thesis is familiar with the problems of optical fibers and possi- bilities creating functional optical structures in optical fibers. first section focuses on the optical fibers and their properties. Another chapter deals with the functional structures of optical fiber and their production. Next section is devoted to the analysis of combinations of these functional structures and their potential applications in sensors. Subsequently, a combined structure is proposed, which is later produced, measured and evaluated for possible use in the sensors

<p>Fiber-optic communication systems have revolutionized the telecommunications industry and have played a major role in the advent of the Information Age. Thousands of kilometers of optical fiber are used by telecommunications companies to transmit telephone signals, Internet communication, and cable television signals throughout the world. So, working in this area has always been interesting. This thesis analyzes the nonlinearity of fiber-optic systems and proposes a system to mitigate fiber nonlinear e®ects. The topics of this thesis can be categorized into two parts. In the first part of thesis (Chapters 2, 3, and 4), analytical models are developed for fiber-optic nonlinear effects. It is important to have an accurate analytical model so that the impact of a specific system/signal parameter on the performance can be assessed quickly without doing time-consuming Monte-Carlo simulations. In the second part (Chapters 5, and 6), a multi-core/fiber architecture is proposed to reduce the nonlinear effects.</p> <p>In Chapter 2, intrachannel nonlinear impairments are studied and an analytical model for the calculation of power spectral density (PSD) and variance of the non- linear distortion is obtained based on quadrature phase-shift keying (QPSK) signal. For QPSK signals, intrachannel four-wave mixing (IFWM) is the only stochastic non- linear distortion. To develop the analytical model, a first order perturbation theory is used. For a Gaussian pulse shape, a closed form formula is obtained for the PSD of IFWM. For non-Gaussian pulses, it is not possible to find the PSD analytically. However, using stationary phase approximation approach, convolutions become multiplications and a simple analytical expression for the PSD of the nonlinear distortion can be found. The total PSD is obtained by adding the PSD of amplified spontaneous emission (ASE) PSD to that of the nonlinear distortion. Using the total PSD, bit error ratio (BER) can be obtained analytically for a QPSK system. The analytically estimated BER is found to be in good agreement with numerical simulations. Significant computational effort can be saved using the analytical model as compared to numerical simulations, without sacrificing much accuracy.</p> <p>In Chapter 3, the same approach as that in Chapter 2 is used to find an analytical expression for the PSD of the intrachannel nonlinear distortion of a fiber-optic system based on quadrature amplitude modulation (QAM) signal. Unlike the QPSK signal, intrachannel cross-phase modulation (IXPM) is a stochastic process for the QAM signal which leads to the increase of the nonlinear distortion variance. In this chapter, analytical expressions for the PSDs of self-phase modulation (SPM), IXPM, IFWM, and their correlations are obtained for the QAM signal. Simulation results show good agreement between the analytical model and numerical simulation.</p> <p>In Chapter 4, inter-channel nonlinear impairment is studied. This time, a first order perturbation technique is used to develop an analytical model for SPM and cross-phase modulation (XPM) distortions in a wavelength division multiplexing (WDM) system based on QAM. In this case, SPM distortion is deterministic and does not contribute to the nonlinear noise variance. On the other hand, XPM is stochastic and contributes to the noise variance. In this chapter, effects of input launch power, fiber dispersion, system reach, and channel spacing on the nonlinear noise variance are investigated as well.</p> <p>In Chapter 5, a single-channel multi-core/fiber architecture is proposed to reduce intrachannel fiber nonlinear effects. Based on the analytical model obtained in the first part of thesis, the nonlinear distortion variance scales as P³, where P is the fiber input launch power, which suggests that decreasing the fiber input power can reduce the nonlinear distortion significantly. In this system, the input power is divided between multiple cores/fibers by a power splitter at the input of each span and a power combiner adds the output fields of multiple cores/fibers so that one amplifier can be used for each span. In this case, each core/fiber receives less power and hence adds less nonlinear distortion to the signal. In a practical system, individual fiber parameters are not identical; so the optical pulses propagating in the fibers undergo different amounts of phase shifts and timing delays due to the fluctuations of fibers' propagation constants and fibers' inverse group speeds. Optical and electrical equalizers are proposed to compensate for these inter-core/fiber dispersions. In the case of an optical equalizer, adaptive time shifters and phase shifters are adjusted such that the maximum power is obtained at the output of power combiner. Our numerical simulation results show that for unrepeatered systems, the performance (Q factor) is improved by 6.2 dB using 8-core/fiber configuration as compared to single- core fiber system. In addition, for multi-span system, the transmission reach at BER of 2.1*10^-3 is quadrupled in 8-core/fiber configuration.</p> <p>In Chapter 6, a multi-channel multi-core/fiber architecture is proposed to reduce the inter-channel nonlinear distortions. In this architecture, different channels of a WDM system are interleaved between multiple cores/fibers which increases the channel spacing in each core/fiber. Higher channel spacing decreases the inter-channel nonlinear impairments in each core/fiber which leads to system performance improvement. At the end of each span, a multiplexer adds the channels from different cores/fibers so that one amplifier can be used for all of the channels. Unlike the single-channel multi-core/fiber system, the WDM multi-core/fiber system does not require equalizers since different cores/fibers carry channels with different frequencies. Simulation results show that for a 39-span system, the 4-core/fiber system with negligible crosstalk outperforms the single-core system by 2.2 dBQ₂₀. The impact of crosstalk between cores of a multi-core fiber (MCF) on the system performance is studied. The simulation results show that the performance of the multi-core WDM system is less sensitive to the crosstalk effect compared to conventional multi-core systems since the propagating channels in the cores are not correlated in frequency domain.</p> / Doctor of Philosophy (PhD)