This dissertation evaluates the possibilities and limitations of rock type identification in rock cutting with conical picks. For this, machine learning in conjunction with features derived from high frequency cutting force measurements is used. On the basis of linear cutting experiments, it is shown that boundary layers can be identified with a precision of less than 3.7 cm when using the developed programme routine. It is further shown that rocks weakened by cracks can be well identified and that anisotropic rock behaviour may be problematic to the classification success. In a case study, it is shown that the supervised algorithms artificial neural network and distributed random forest perform relatively well while unsupervised k-means clustering provides limited accuracies for complex situations. The 3d-results are visualised in a web app. The results suggest that a possible rock classification system can achieve good results—that are robust to changes in the cutting parameters when using the proposed evaluation methods.:1 Introduction...1 2 Cutting Excavation with Conical Picks...5 2.1 Cutting Process...8 2.1.2 Cutting Parameters...11 2.1.3 Influences of Rock Mechanical Properties...17 2.1.4 Influences of the Rock Mass...23 2.2 Ratios of Cutting Force Components...24 3 State of the Art...29 3.1 Data Analysis in Rock Cutting Research...29 3.2 Rock Classification Systems...32 3.2.1 MWC – Measure-While-Cutting...32 3.2.2 MWD – Measuring-While-Drilling...34 3.2.3 Automated Profiling During Cutting...35 3.2.4 Wear Monitoring...36 3.3 Machine learning for Rock Classification...36 4 Problem Statement and Justification of Topic...38 5 Material and Methods...40 5.1 Rock Cutting Equipment...40 5.2 Software & PC...42 5.3 Samples and Rock Cutting Parameters...43 5.3.1 Sample Sites...43 5.3.2 Experiment CO – Zoned Concrete...45 5.3.3 Experiment GN – Anisotropic Rock Gneiss...47 5.3.4 Experiment GR – Uncracked and Cracked Granite...49 5.3.5 Case Study PB and FBA – Lead-Zinc and Fluorite-Barite Ores...50 5.4 Data Processing...53 5.5 Force Component Ratio Calculation...54 5.6 Procedural Selection of Features...57 5.7 Image-Based Referencing and Rock Boundary Modelling...60 5.8 Block Modelling and Gridding...61 5.9 Correlation Analysis...63 5.10 Regression Analysis of Effect...64 5.11 Machine Learning...65 5.11.2 K-Means Algorithm...66 5.11.3 Artificial Neural Networks...67 5.11.4 Distributed Random Forest...70 5.11.5 Classification Success...72 5.11.6 Boundary Layer Recognition Precision...73 5.12 Machine Learning Case Study...74 6 Results...75 6.1 CO – Zoned Concrete...75 6.1.1 Descriptive Statistics...75 6.1.2 Procedural Evaluation...76 6.1.3 Correlation of the Covariates...78 6.1.4 K-Means Cluster Analysis...79 6.2 GN – Foliated Gneiss...85 6.2.1 Cutting Forces...86 6.2.2 Regression Analysis of Effect...88 6.2.3 Details Irregular Behaviour...90 6.2.4 Interpretation of Anisotropic Behaviour...92 6.2.5 Force Component Ratios...92 6.2.6 Summary and Interpretations of Results...93 6.3 CR – Cracked Granite...94 6.3.1 Force Component Results...94 6.3.2 Spatial Analysis...97 6.3.3 Error Analysis...99 6.3.4 Summary...100 6.4 Case Study...100 6.4.1 Feature Distribution in Block Models...101 6.4.2 Distributed Random Forest...105 6.4.3 Artificial Neural Network...107 6.4.4 K-Means...110 6.4.5 Training Data Required...112 7 Discussion...114 7.1 Critical Discussion of Experimental Results...114 7.1.1 Experiment CO...114 7.1.2 Experiment GN...115 7.1.3 Experiment GR...116 7.1.4 Case Study...116 7.1.5 Additional Outcomes...117 7.2 Comparison of Machine Learning Algorithms...118 7.2.1 K-Means...118 7.2.2 Artificial Neural Networks and Distributed Random Forest...119 7.2.3 Summary...120 7.3 Considerations Towards Sensor System...121 7.3.1 Force Vectors and Data Acquisition Rate...121 7.3.2 Sensor Types...122 7.3.3 Computation Speed...123 8 Summary and Outlook...125 References...128 Annex A Fields of Application of Conical Tools...145 Annex B Supplements Cutting and Rock Parameters...149 Annex C Details Topic-Analysis Rock Cutting Publications...155 Annex D Details Patent Analysis...157 Annex E Details Rock Cutting Unit HSX-1000-50...161 Annex F Details Used Pick...162 Annex G Error Analysis Cutting Experiments...163 Annex H Details Photographic Modelling...166 Annex I Laser Offset...168 Annex J Supplements Experiment CO...169 Annex K Supplements Experiment GN...187 Annex L Supplements Experiment GR...191 Annex M Preliminary Artificial Neural Network Training...195 Annex N Supplements Case Study (CD)...201 Annex O R-Codes (CD)...203 Annex P Supplements Rock Mechanical Tests (CD)...204 / Die Dissertation evaluiert Möglichkeiten und Grenzen der Gebirgserkennung bei der schneidenden Gewinnung von Festgesteinen mit Rundschaftmeißeln unter Nutzung maschinellen Lernens – in Verbindung mit aus hochaufgelösten Schnittkraftmessungen abgeleiteten Kennwerten. Es wird auf linearen Schneidversuchen aufbauend gezeigt, dass Schichtgrenzen mit Genauigkeiten unter 3,7 cm identifiziert werden können. Ferner wird gezeigt, dass durch Risse geschwächte Gesteine gut identifiziert werden können und dass anisotropes Gesteinsverhalten möglicherweise problematisch auf den Klassifizierungserfolg wirkt. In einer Fallstudie wird gezeigt, dass die überwachten Algorithmen Künstliches Neurales Netz und Distributed Random Forest teils sehr gute Ergebnisse erzielen und unüberwachtes k-means-Clustering begrenzte Genauigkeiten für komplexe Situationen liefert. Die Ergebnisse werden in einer Web-App visualisiert. Aus den Ergebnissen wird abgeleitet, dass ein mögliches Sensorsystem mit den vorgeschlagenen Auswerteroutinen gute Ergebnisse erzielen kann, die gleichzeitig robust gegen Änderungen der Schneidparameter sind.:1 Introduction...1 2 Cutting Excavation with Conical Picks...5 2.1 Cutting Process...8 2.1.2 Cutting Parameters...11 2.1.3 Influences of Rock Mechanical Properties...17 2.1.4 Influences of the Rock Mass...23 2.2 Ratios of Cutting Force Components...24 3 State of the Art...29 3.1 Data Analysis in Rock Cutting Research...29 3.2 Rock Classification Systems...32 3.2.1 MWC – Measure-While-Cutting...32 3.2.2 MWD – Measuring-While-Drilling...34 3.2.3 Automated Profiling During Cutting...35 3.2.4 Wear Monitoring...36 3.3 Machine learning for Rock Classification...36 4 Problem Statement and Justification of Topic...38 5 Material and Methods...40 5.1 Rock Cutting Equipment...40 5.2 Software & PC...42 5.3 Samples and Rock Cutting Parameters...43 5.3.1 Sample Sites...43 5.3.2 Experiment CO – Zoned Concrete...45 5.3.3 Experiment GN – Anisotropic Rock Gneiss...47 5.3.4 Experiment GR – Uncracked and Cracked Granite...49 5.3.5 Case Study PB and FBA – Lead-Zinc and Fluorite-Barite Ores...50 5.4 Data Processing...53 5.5 Force Component Ratio Calculation...54 5.6 Procedural Selection of Features...57 5.7 Image-Based Referencing and Rock Boundary Modelling...60 5.8 Block Modelling and Gridding...61 5.9 Correlation Analysis...63 5.10 Regression Analysis of Effect...64 5.11 Machine Learning...65 5.11.2 K-Means Algorithm...66 5.11.3 Artificial Neural Networks...67 5.11.4 Distributed Random Forest...70 5.11.5 Classification Success...72 5.11.6 Boundary Layer Recognition Precision...73 5.12 Machine Learning Case Study...74 6 Results...75 6.1 CO – Zoned Concrete...75 6.1.1 Descriptive Statistics...75 6.1.2 Procedural Evaluation...76 6.1.3 Correlation of the Covariates...78 6.1.4 K-Means Cluster Analysis...79 6.2 GN – Foliated Gneiss...85 6.2.1 Cutting Forces...86 6.2.2 Regression Analysis of Effect...88 6.2.3 Details Irregular Behaviour...90 6.2.4 Interpretation of Anisotropic Behaviour...92 6.2.5 Force Component Ratios...92 6.2.6 Summary and Interpretations of Results...93 6.3 CR – Cracked Granite...94 6.3.1 Force Component Results...94 6.3.2 Spatial Analysis...97 6.3.3 Error Analysis...99 6.3.4 Summary...100 6.4 Case Study...100 6.4.1 Feature Distribution in Block Models...101 6.4.2 Distributed Random Forest...105 6.4.3 Artificial Neural Network...107 6.4.4 K-Means...110 6.4.5 Training Data Required...112 7 Discussion...114 7.1 Critical Discussion of Experimental Results...114 7.1.1 Experiment CO...114 7.1.2 Experiment GN...115 7.1.3 Experiment GR...116 7.1.4 Case Study...116 7.1.5 Additional Outcomes...117 7.2 Comparison of Machine Learning Algorithms...118 7.2.1 K-Means...118 7.2.2 Artificial Neural Networks and Distributed Random Forest...119 7.2.3 Summary...120 7.3 Considerations Towards Sensor System...121 7.3.1 Force Vectors and Data Acquisition Rate...121 7.3.2 Sensor Types...122 7.3.3 Computation Speed...123 8 Summary and Outlook...125 References...128 Annex A Fields of Application of Conical Tools...145 Annex B Supplements Cutting and Rock Parameters...149 Annex C Details Topic-Analysis Rock Cutting Publications...155 Annex D Details Patent Analysis...157 Annex E Details Rock Cutting Unit HSX-1000-50...161 Annex F Details Used Pick...162 Annex G Error Analysis Cutting Experiments...163 Annex H Details Photographic Modelling...166 Annex I Laser Offset...168 Annex J Supplements Experiment CO...169 Annex K Supplements Experiment GN...187 Annex L Supplements Experiment GR...191 Annex M Preliminary Artificial Neural Network Training...195 Annex N Supplements Case Study (CD)...201 Annex O R-Codes (CD)...203 Annex P Supplements Rock Mechanical Tests (CD)...204

No description available.

The diploma thesis is focused on machining using the ball-end shank mill. Content of the preliminary part of the work is a shank mill characteristic and a consequent part shows a splitting of ball-end milling cutters, its application, the cutting tool geometry and a characteristic signs of machining. The cutting force model of the ball-end mill is presented as well. A part of proposed model is the conversion of the resultant force too. Practical part is aimed at cutting force analysis of the ball-end mill and the main purpose of this part is a quantification of the cutting force for different work piece tilt angles while milling is performed.

Pesquisadores e indústrias de todo o mundo estão firmemente comprometidos com o propósito de fazer o processo de usinagem ser precisamente veloz e produtivo. A forte concorrência mundial gerou a procura por processos de usinagem econômicos, com grande capacidade de produção de cavacos e que produzam peças com elevada qualidade. Dentre as novas tecnologias que começaram a ser empregadas, e deve tornar-se o caminho certo a ser trilhado na busca da competitividade em curto espaço de tempo, está a tecnologia de usinagem com altas velocidades (HSM de High Speed Machining). A tecnologia HSM surge como componente essencial na otimização dos esforços para manutenção e aumento da competitividade global das empresas. Durante os últimos anos a usinagem com alta velocidade tem ganhado grande importância, sendo dada uma maior atenção ao desenvolvimento e à disponibilização no mercado de máquinas-ferramentas com rotações muito elevadas (20.000 - 100.000 rpm). O processo de usinagem com alta velocidade está sendo usado não apenas para ligas de alumínio e cobre, mas também para materiais de difícil usinabilidade, como os aços temperados e superligas à base de níquel. Porém, quando se trata de materiais de difícil corte, têm-se observado poucas publicações, principalmente no processo de torneamento. Mas, antes que a tecnologia HSM possa ser empregada de uma forma econômica, todos os componentes envolvidos no processo de usinagem, incluindo a máquina, o eixo-árvore, a ferramenta e o pessoal, precisam estar afinados com as peculiaridades deste novo processo. No que diz respeito às máquinas-ferramenta, isto significa que elas têm que satisfazer requisitos particulares de segurança. As ferramentas, devido à otimização de suas geometrias, substratos e revestimentos, contribuem para o sucesso deste processo. O presente trabalho objetiva estudar o comportamento de diversas geometrias ) de insertos de cerâmica (Al2O3 + SiCw e Al2O3 + TIC) e PCBN com duas concentrações de CBN na forma padrão, assim como modificações na geometria das arestas de corte empregadas em torneamento com alta velocidade em superligas à base de níquel (Inconel 718 e Waspaloy). Os materiais foram tratados termicamente para dureza de 44 e 40 HRC respectivamente, e usinados sob condição de corte a seco e com utilização da técnica de mínima quantidade de lubrificante (minimal quantity lubricant - MQL) visando atender requisitos ambientais. As superligas à base de níquel são conhecidas como materiais de difícil usinabilidade devido à alta dureza, alta resistência mecânica em alta temperatura, afinidade para reagir com materiais da ferramenta e baixa condutividade térmica. A usinagem de superligas afeta negativamente a integridade da peça. Por essa razão, cuidados especiais devem ser tomados para assegurar a vida da ferramenta e a integridade superficial de componentes usinados por intermédio de controle dos principais parâmetros de usinagem. Experimentos foram realizados sob diversas condições de corte e geometrias de ferramentas para avaliação dos parâmetros: força de corte, temperatura, emissão acústica e integridade superficial (rugosidade superficial, tensão residual, microdureza e microestrutura) e mecanismos de desgaste. Mediante os resultados apresentados, recomenda-se à geometria de melhor desempenho nos parâmetros citados e confirma-se a eficiência da técnica MQL. Dentre as ferramentas e geometrias testadas, a que apresentou melhor desempenho foi a ferramenta cerâmica CC650 seguida da ferramenta cerâmica CC670 ambas com formato redondo e geometria 2 (chanfro em T de 0,15 x 15º com raio de aresta de 0,03 mm). / Researchers and industry personnel around the world are firmly committed to the purpose of doing the machining process dramatically faster and more precise. The tough global competition has generated a search for more economical machining processes, with high ability for chip removal and, in this way, producing high quality workpieces. Among the new technologies available nowadays, the high speed machining (HSM) is pointed out as the main solution to obtain competitiveness in a short period of time. The HSM technology appears as an essential component to optimize the efforts for maintaining, and increasing, the global competitiveness. During the last years, high speed machining technology has received great attention, specially the development and availability in the market of machine tools with high rotational speeds (20.000 - 100.000 rpm). The HSM has been used not only to machine aluminum and copper alloys, but also to difficult to machine rnaterials, such as hardened steels and nickel based superalIoys. However, for difficult to machine materiais, the literature is very incipient, specially concerning the turning process. However, before the HSM technology be used in an economic way, alI the components involved in the machining process, including the machine, the spindle, the tool and the operators, need to be tuned with the peculiarities of this new process. Concerning the tooling, they have to satisfy peculiar requirements of safety. Due to the optimization of their geometries, substrates and coatings, the cutting tools are contributing to the success of the process. The present work aims at the study of several insert geometries of ceramic tools (Al2O3 + SiCw and Al2O3 + TiC) and PCBN, with two concentrations of CBN, in the standard format and with modifications on the cutting edge geometry, working in the high speed turning of nickel based superaIloys (lnconel 718 and Waspaloy]. MateriaIs were heat treated to hardness of 44 and 40 HRC, respectively, and machined under dry cutting condition and also with minimal quantity of lubricant (MQL) to attend environmental requirements. The nickel based superalloys are known as difficult to cut materials due to their high hardness, high mechanical strength at high temperature, chemical affinity to tool materiaIs and lower thermal conductivity. The machining of superalloys affects negatively the integrity of the workpiece. For this reason, tool life and surface integrity of the machined component must be carefully analyzed throughout the control of the main machining parameters. Practical experiments were implemented using several cutting conditions and tool geometries to evaluate the following parameters: cutting force, temperature, acoustic emission and surface integrity (surface finishing, residual stress, microhardeness and microstructure) and wear mechanisms. Analyzing the results, the most suitable geometry for the mentioned parameters is recommended and the efficiency of the MQL technical is confirmed. Among all inserts and geometries tested, the CC650 ceramic tool presented better results, followed by the CC670 ceramic tool, both with round format and edge geometry number 2 (chamfer in T 0,15 x 15° with hone of 0,03 mm).

Pesquisadores e indústrias de todo o mundo estão firmemente comprometidos com o propósito de fazer o processo de usinagem ser precisamente veloz e produtivo. A forte concorrência mundial gerou a procura por processos de usinagem econômicos, com grande capacidade de produção de cavacos e que produzam peças com elevada qualidade. Dentre as novas tecnologias que começaram a ser empregadas, e deve tornar-se o caminho certo a ser trilhado na busca da competitividade em curto espaço de tempo, está a tecnologia de usinagem com altas velocidades (HSM de High Speed Machining). A tecnologia HSM surge como componente essencial na otimização dos esforços para manutenção e aumento da competitividade global das empresas. Durante os últimos anos a usinagem com alta velocidade tem ganhado grande importância, sendo dada uma maior atenção ao desenvolvimento e à disponibilização no mercado de máquinas-ferramentas com rotações muito elevadas (20.000 - 100.000 rpm). O processo de usinagem com alta velocidade está sendo usado não apenas para ligas de alumínio e cobre, mas também para materiais de difícil usinabilidade, como os aços temperados e superligas à base de níquel. Porém, quando se trata de materiais de difícil corte, têm-se observado poucas publicações, principalmente no processo de torneamento. Mas, antes que a tecnologia HSM possa ser empregada de uma forma econômica, todos os componentes envolvidos no processo de usinagem, incluindo a máquina, o eixo-árvore, a ferramenta e o pessoal, precisam estar afinados com as peculiaridades deste novo processo. No que diz respeito às máquinas-ferramenta, isto significa que elas têm que satisfazer requisitos particulares de segurança. As ferramentas, devido à otimização de suas geometrias, substratos e revestimentos, contribuem para o sucesso deste processo. O presente trabalho objetiva estudar o comportamento de diversas geometrias ) de insertos de cerâmica (Al2O3 + SiCw e Al2O3 + TIC) e PCBN com duas concentrações de CBN na forma padrão, assim como modificações na geometria das arestas de corte empregadas em torneamento com alta velocidade em superligas à base de níquel (Inconel 718 e Waspaloy). Os materiais foram tratados termicamente para dureza de 44 e 40 HRC respectivamente, e usinados sob condição de corte a seco e com utilização da técnica de mínima quantidade de lubrificante (minimal quantity lubricant - MQL) visando atender requisitos ambientais. As superligas à base de níquel são conhecidas como materiais de difícil usinabilidade devido à alta dureza, alta resistência mecânica em alta temperatura, afinidade para reagir com materiais da ferramenta e baixa condutividade térmica. A usinagem de superligas afeta negativamente a integridade da peça. Por essa razão, cuidados especiais devem ser tomados para assegurar a vida da ferramenta e a integridade superficial de componentes usinados por intermédio de controle dos principais parâmetros de usinagem. Experimentos foram realizados sob diversas condições de corte e geometrias de ferramentas para avaliação dos parâmetros: força de corte, temperatura, emissão acústica e integridade superficial (rugosidade superficial, tensão residual, microdureza e microestrutura) e mecanismos de desgaste. Mediante os resultados apresentados, recomenda-se à geometria de melhor desempenho nos parâmetros citados e confirma-se a eficiência da técnica MQL. Dentre as ferramentas e geometrias testadas, a que apresentou melhor desempenho foi a ferramenta cerâmica CC650 seguida da ferramenta cerâmica CC670 ambas com formato redondo e geometria 2 (chanfro em T de 0,15 x 15º com raio de aresta de 0,03 mm). / Researchers and industry personnel around the world are firmly committed to the purpose of doing the machining process dramatically faster and more precise. The tough global competition has generated a search for more economical machining processes, with high ability for chip removal and, in this way, producing high quality workpieces. Among the new technologies available nowadays, the high speed machining (HSM) is pointed out as the main solution to obtain competitiveness in a short period of time. The HSM technology appears as an essential component to optimize the efforts for maintaining, and increasing, the global competitiveness. During the last years, high speed machining technology has received great attention, specially the development and availability in the market of machine tools with high rotational speeds (20.000 - 100.000 rpm). The HSM has been used not only to machine aluminum and copper alloys, but also to difficult to machine rnaterials, such as hardened steels and nickel based superalIoys. However, for difficult to machine materiais, the literature is very incipient, specially concerning the turning process. However, before the HSM technology be used in an economic way, alI the components involved in the machining process, including the machine, the spindle, the tool and the operators, need to be tuned with the peculiarities of this new process. Concerning the tooling, they have to satisfy peculiar requirements of safety. Due to the optimization of their geometries, substrates and coatings, the cutting tools are contributing to the success of the process. The present work aims at the study of several insert geometries of ceramic tools (Al2O3 + SiCw and Al2O3 + TiC) and PCBN, with two concentrations of CBN, in the standard format and with modifications on the cutting edge geometry, working in the high speed turning of nickel based superaIloys (lnconel 718 and Waspaloy]. MateriaIs were heat treated to hardness of 44 and 40 HRC, respectively, and machined under dry cutting condition and also with minimal quantity of lubricant (MQL) to attend environmental requirements. The nickel based superalloys are known as difficult to cut materials due to their high hardness, high mechanical strength at high temperature, chemical affinity to tool materiaIs and lower thermal conductivity. The machining of superalloys affects negatively the integrity of the workpiece. For this reason, tool life and surface integrity of the machined component must be carefully analyzed throughout the control of the main machining parameters. Practical experiments were implemented using several cutting conditions and tool geometries to evaluate the following parameters: cutting force, temperature, acoustic emission and surface integrity (surface finishing, residual stress, microhardeness and microstructure) and wear mechanisms. Analyzing the results, the most suitable geometry for the mentioned parameters is recommended and the efficiency of the MQL technical is confirmed. Among all inserts and geometries tested, the CC650 ceramic tool presented better results, followed by the CC670 ceramic tool, both with round format and edge geometry number 2 (chamfer in T 0,15 x 15° with hone of 0,03 mm).