DC power distribution has gained popularity in sustainable buildings, renewable energy utilization, transportation electrification and high-efficiency data centers. This dissertation focuses on two aspects of facilitating the application of dc systems: (a) system-level control to improve load sharing, voltage regulation and efficiency; (b) design of a high-efficiency interface converter to connect dc microgrids with the existing low-voltage ac distributions, with a special focus on common-mode (CM) voltage attenuation. Droop control has been used in dc microgrids to share loads among multiple sources. However, line resistance and sensor discrepancy deteriorate the performance. The quantitative relation between the droop voltage range and the load sharing accuracy is derived to help create droop design guidelines. DC system designers can use the guidelines to choose the minimum droop voltage range and guarantee that the sharing error is within a defined range even under the worst cases. A nonlinear droop method is proposed to improve the performance of droop control. The droop resistance is a function of the output current and increases when the output current increases. Experiments demonstrate that the nonlinear droop achieves better load sharing under heavy load and tighter bus voltage regulation. The control needs only local information, so the advantages of droop control are preserved. The output impedances of the droop-controlled power converters are also modeled and measured for the system stability analysis. Communication-based control is developed to further improve the performance of dc microgrids. A generic dc microgrid is modeled and the static power flow is solved. A secondary control system is presented to achieve the benefits of restored bus voltage, enhanced load sharing and high system efficiency. The considered method only needs the information from its adjacent node; hence system expendability is guaranteed. A high-efficiency two-stage single-phase ac-dc converter is designed to connect a 380 V bipolar dc microgrid with a 240 V split-phase single-phase ac system. The converter efficiencies using different two-level and three-level topologies with state-of-the-art semiconductor devices are compared, based on which a two-level interleaved topology using silicon carbide (SiC) MOSFETs is chosen. The volt-second applied on each inductive component is analyzed and the interleaving angles are optimized. A 10 kW converter prototype is built and achieves an efficiency higher than 97% for the first time. An active CM duty cycle injection method is proposed to control the dc and low-frequency CM voltage for grounded systems interconnected with power converters. Experiments with resistive and constant power loads in rectification and regeneration modes validate the performance and stability of the control method. The dc bus voltages are rendered symmetric with respect to ground, and the leakage current is reduced. The control method is generalized to three-phase ac-dc converters for larger power systems. / Ph. D.

Master of Science / Department of Architectural Engineering and Construction Science / Fred Hasler / This paper discusses a brief history of electricity, specifically alternating current (AC) and direct current (DC), and how the current standard of AC distribution has been reached. DC power was first produced in 1800, but the shift to AC occurred in the 1880’s with the advent of the transformer. Because the decisions for distribution were made over 100 years ago, it could be time to rethink the standards of power distribution. Compared to traditional AC distribution, DC microgrids are significantly more energy efficient when implemented with distributed generation. Distributed generation, or on-site generation from photovoltaic panels, wind turbines, fuel cells, or microturbines, is more efficient when the power is transmitted by DC. DC generation, paired with the growing DC load profile, increases energy savings by utilizing DC architecture and eliminating wasteful conversions. Energy savings would result from a lower grid strain and more efficient utilization of the utility grid. DC distribution results in a more reliable electrical service due to short transmission distances, high service reliability when paired with on-site generation, and efficient storage. Occupant safety is a perceived concern with DC microgrids due to the lack of knowledge and familiarity in regards to these systems. However, with proper regulation and design standards, building occupants never encounter voltage higher than 24VDC, which is significantly safer than existing 120VAC in the United States. DC Microgrids have several disadvantages such as higher initial cost due, in part, to unfamiliarity of the system as well as a general lack of code recognition and efficiency metric recognition leading to difficult certification and code compliance. Case studies are cited in this paper to demonstrate energy reduction possibilities due to the lack of modeling ability in current energy analysis programs and demonstrated energy savings of approximately 20%. It was concluded that continued advancement in code development will come from pressure to increase energy efficiency. This pressure, paired with the standardization of a 24VDC plug and socket, will cause substantial increases in DC microgrid usage in the next 10 years.