A novel hybrid pulse-width modulation (PWM) update method is proposed to eliminate the effect of the one-step control time delay Td one without losing the full duty cycle range. Without the Td one to cause linear phase shifts that limit the control bandwidth and affect closed-loop stability, a very high quality digital current control can be achieved, such as a high closed current loop bandwidth, strong robustness against disturbances, ability to reach a very high fundamental frequency compared to switching frequency, etc. In a conventional digital control implementation, a sampling period (Tsamp) is allocated for the execution of samplings and computations, and the update of PWM outputs is delayed until the beginning of the following sampling period. This delayed PWM update method is the cause of the Td one. Instead of the delayed PWM update, if the PWM outputs are updated immediately after algorithm computations, then the effect of the Td one can be eliminated; however, the computation time delay Td comp from the current sampling instant through algorithm computations to the PWM update instant causes a reduced duty cycle range. Each of these two conventional PWM update methods has some shortcomings. A hybrid PWM update method is proposed to circumvent the aforementioned shortcomings and to incorporate only the advantages. The proposed method improves the performance by updating the PWM outputs multiple times during a Tsamp, whereas the PWM outputs are updated only one time during a Tsamp in the conventional methods. In spite of the simplicity of the proposed method, the performance improvements in stability, robustness and response characteristics are significant. On the other hand, the proposed method can be easily applied to many PWM based digital controls because of its simplicity. Additional to the hybrid PWM update method, a hybrid control method is proposed to optimize the sequence of control operations. It maximizes the current loops' robustness and minimizes the delay from the sampling of outer control loops' variables, such as voltage and speed, to the duty cycle update instant. The minimum delay enables the maximization of the outer control loops' bandwidth. Additionally, a corrective neutral offset voltage injection method is proposed to correct small PWM output deviations that may occur with the hybrid PWM update method. Utilizing a three-phase voltage source inverter with a permanent magnet synchronous machine as the platform, a deadbeat current control and a high speed ac drive experiments have been conducted to demonstrate the feasibility and validity. Notable results include a closed current loop response of one Tsamp with the deadbeat control and a 500 Hz current fundamental frequency with 1 kHz switching frequency in the high speed ac drive. / Ph. D.

<p>This project deals with voltage source converters with energy storage capability. The main objective is to study the possible benefits of energy storage to a power system with a VSC as the interface between them.</p><p>First of all, a converter control system is proposed for a two level VSC. In the conventional converter control, the control system usually takes the voltage measured at the point where the converter is connected and calculates the reference voltage for the converter; with a modulation system the converter then produces the required 'average voltage'. In this project, a novel flux modulation scheme, combined with the deadbeat current control strategy, is proposed. The current controller is capable of controlling both positive and negative sequence current components. With flux modulation, the control system measures the bus flux and commands the converter to generate the required flux.</p><p>Based on the proposed control strategies, several application studies have been carried out.</p><p>The first application study investigates the effect of energy storage on the power quality at the point of common coupling when a system is subject to load disturbances. The voltage at PCC in a weak network is very sensitive to load changes. A sudden change in active load will cause both a phase jump and a magnitude fluctuation in the bus voltage, whereas reactive load changes mainly affect the voltage magnitude. With the addition of energy storage to a StatCom, it is possible to compensate for the active power change as well as providing reactive power support. In this thesis, some effective active power compensation schemes are proposed. Simulations and experiments have been performed to verify the compensation schemes. The results show that a StatCom with energy storage can significantly reduce phase jumps and magnitude deviations of the bus voltage.</p><p>pact of the energy storage on the performance of weak systems under fault conditions has been investigated. The investigation was done by studying an example system. The system model was established based on a real system, in which some induction motors driving pumps along a pipeline are fed from a radial transmission line. Studies show that for a weak system with induction motor loads, a StatCom with certain energy storage capacity will effectively improve the system recovery after faults. Although this incurs extra cost for the increasing dc voltage rating and size of the dc side capacitor, the overall rating of the converter can be reduced by utilization of the proposed active power compensation scheme.</p><p>The last case study investigates the possible use of a StatCom with energy storage to improve the power quality at the point of common coupling where a cyclic load is connected. Studies show that by providing both fast reactive and fast active power support to the network, not only the voltage magnitude can be well controlled, but also the voltage phase jump can be reduced significantly.</p>

This project deals with voltage source converters with energy storage capability. The main objective is to study the possible benefits of energy storage to a power system with a VSC as the interface between them. First of all, a converter control system is proposed for a two level VSC. In the conventional converter control, the control system usually takes the voltage measured at the point where the converter is connected and calculates the reference voltage for the converter; with a modulation system the converter then produces the required 'average voltage'. In this project, a novel flux modulation scheme, combined with the deadbeat current control strategy, is proposed. The current controller is capable of controlling both positive and negative sequence current components. With flux modulation, the control system measures the bus flux and commands the converter to generate the required flux. Based on the proposed control strategies, several application studies have been carried out. The first application study investigates the effect of energy storage on the power quality at the point of common coupling when a system is subject to load disturbances. The voltage at PCC in a weak network is very sensitive to load changes. A sudden change in active load will cause both a phase jump and a magnitude fluctuation in the bus voltage, whereas reactive load changes mainly affect the voltage magnitude. With the addition of energy storage to a StatCom, it is possible to compensate for the active power change as well as providing reactive power support. In this thesis, some effective active power compensation schemes are proposed. Simulations and experiments have been performed to verify the compensation schemes. The results show that a StatCom with energy storage can significantly reduce phase jumps and magnitude deviations of the bus voltage. pact of the energy storage on the performance of weak systems under fault conditions has been investigated. The investigation was done by studying an example system. The system model was established based on a real system, in which some induction motors driving pumps along a pipeline are fed from a radial transmission line. Studies show that for a weak system with induction motor loads, a StatCom with certain energy storage capacity will effectively improve the system recovery after faults. Although this incurs extra cost for the increasing dc voltage rating and size of the dc side capacitor, the overall rating of the converter can be reduced by utilization of the proposed active power compensation scheme. The last case study investigates the possible use of a StatCom with energy storage to improve the power quality at the point of common coupling where a cyclic load is connected. Studies show that by providing both fast reactive and fast active power support to the network, not only the voltage magnitude can be well controlled, but also the voltage phase jump can be reduced significantly. / QC 20101124