Replacing organic liquid electrolytes with nonflammable solid electrolytes can improve safety, offer higher volumetric and gravimetric energy densities, and lower the cost of lithium-ion batteries. However, today’s all-solid-state batteries suffer from low Li-ion conductivity in the electrolyte, slow Li-ion transport across the electrolyte/electrode interface, and slow solid-state Li-ion diffusion within the electrode. Defect chemistry is critical to understanding ionic conductivity and predicting the charge transport through heterogeneous solid interfaces. The goal of this dissertation is to analyze and improve solid state materials for energy storage applications by understanding their defect structure and transport properties. I have investigated defect chemistry of cubic Li7La3Zr2O12 (c-LLZO), one of the most promising candidate solid electrolytes for all-solid-state lithium batteries. By combining conductivity measurements with defect modeling, I constructed a defect diagram of c-LLZO featuring the intrinsic formation of lithium vacancy-hole pairs. The findings provided insights into tailoring single-phase mixed lithium-ion/electron conducting materials for emerging ionic devices, i.e., composite cathodes requiring both fast electronic and ionic paths in solid-state batteries. I suggested that oxygen vacancies could increase the Li-ion conductivity by reducing the amount of electron holes bound with lithium vacancies. Using a simpler but also attractive solid electrolyte Li2ZrO3 (LZO) as an example, I significantly improved Li-ion conductivity by creating extra oxygen vacancies via cation doping. In particular, Fe-doped LZO shows the highest Li-ion conductivity reported for the family of LZO compounds, reaching 3.3 mS/cm at 300 °C. This study brought attentions to the long-neglected oxygen vacancy defects in lithium-ion conductors and revealed their critical role in promoting Li-ion transport. More importantly, it established a novel defect engineering strategy for designing Li-oxide based solid electrolytes for all-solid-state batteries. I surface-modified LiNi0.6Co0.2Mn0.2O2 cathode material with a LZO coating prepared under dry air and oxygen, and systematically investigated the effect of coating atmosphere on their transport properties and electrochemical behaviors. The LZO coating prepared in oxygen is largely amorphous. It not only provided surface protection against the electrolyte corrosion but also enabled faster lithium-ion transport. Additionally, oxygen atmosphere facilitated Zr diffusion from the surface coating to the bulk of LiNi0.6Co0.2Mn0.2O2, which stabilized the crystal structure and enhanced lithium ion diffusion. Consequently, LiNi0.6Co0.2Mn0.2O2 cathodes coated with Li2ZrO3 in oxygen achieved a significant improvement in high-voltage cycling stability and high-rate performance.

X-ray diffraction (XRD) patterns, electron probe microanalysis(EPMA), electron paramagnetic resonance (EPR) powder spectra (9 and 34 GHz) and the magnetic susceptibility of BaTiO3 + 0.04 BaO + 0.01 V2O5 ceramics were studied to investigate the valence states of V ions and their solubility in the BaTiO3 lattice. In samples sintered at 1400 °C in air, only about 0.1 mol% V is incorporated in the BaTiO3 lattice being in V4+ and V5+ valence state, respectively. 95% of the nominal V dopant content occurs in the secondary phase Ba3(V/Ti)2O8. All BaTiO3 samples investigated are in tetragonal phase at room temperature. In the as-sintered samples V4+ is detected at temperatures T < 20 K by its hyperfine structure (HFS) octet due to the nuclear spin 7/2 of 51V. Samples post annealed in H2/Ar atmosphere at 1200 °C exhibit a further HFS octet occurring at T > 25 K and vanishing at T > 250 K, which is caused by V2+ ions. This spectrum is characterized by a simultaneous HFS and fine structure splitting constituted by allowed and forbidden transitions. Both V4+ and V2+ ions are incorporated at Ti4+ sites of the BaTiO3 lattice

The development of technologies that enable efficient and reliable energy inter-conversion and storage is of key importance for tempering the intermittent availability of renewable energy sources, and thus for developing an energy economy based on sustainable, clean energy production. Solid oxide electrolysis cells (SOECs) may be used to store excess electrical energy as hydrogen, while solid oxide fuel cells (SOFCs) could convert back hydrogen into electricity, thus balancing energy availability and demand. However, the current state-of-the-art hydrogen electrode used in both SOECs and SOFCs, the Ni-yttria-stabilised zirconia cermet (Ni-YSZ), is unreliable in conjunction with intermittent energy sources, in particular due to its innate redox instability. This thesis explores the fundamental properties of various inherently redox stable A-site deficient titanate perovskite systems (A1-αBO3, B = Ti), seeking to uncover the principles that enhance their properties so that they may be used to replace Ni-YSZ. In particular, this work demonstrates that the versatility of perovskites with respect to the introduction of lattice defects such as vacancies and cation substitutions enables considerable improvements in the extent of reduction, electronic conductivity and overall electrochemical activity. Most importantly, the defect chemistry context set by the presence of A-site vacancies was found to trigger the exsolution of electrocatalytically active nanoparticles from the parent perovskite, upon reduction. This is an entirely new phenomenon which was explored and exploited throughout this study to produce perovskite surfaces decorated with uniformly distributed catalytically active nanoparticles. As demonstrated in this study, the exsolution phenomenon excels in terms of producing nanoparticles with uniform size, distribution, diverse composition and ‘unconventional' surface anchorage. The resulting enhanced properties, and especially the exsolution phenomenon, contributed coherently towards improving the suitability of the perovskites developed here towards their application as hydrogen electrode materials. Consequently, when integrated into SOEC button cells as hydrogen electrodes, they exhibited a step-change increase in performance compared to other perovskites considered to date. Many of the principles and perovskite defect chemistry explored and exemplified in this study on perovskite titanates may be extended to other perovskites as well. In particular the advanced control and understanding achieved in this work over the exsolution phenomenon may inspire the formulation of new and sophisticated oxide materials with advanced functionality.

Fundamental understanding of the behaviour of nuclear fuel has been of great importance. Enhancing this knowledge not only by means of experimental observations, but also via multi-scale modelling is of current interest. The overall goal of this thesis is to understand the impact of atomic interactions on the nuclear fuel material properties. Two major topics are tackled in this thesis. The first topic deals with non-stoichiometry in uranium dioxide (UO2) to be addressed by empirical potential (EP) studies. The second fundamental question to be answered is the effect of the atomic fraction of americium (Am), neptunium (Np) containing uranium (U) and plutonium (Pu) mixed oxide (MOX) on the material properties.UO2 has been the reference fuel for the current fleet of nuclear reactors (Gen-II and Gen-III); it is also considered today by the Gen-IV International Forum for the first cores of the future generation of nuclear reactors on the roadmap towards minor actinide (MA) based fuel technology. The physical properties of UO2 highly depend on material stoichiometry. In particular, oxidation towards hyper stoichiometric UO2 – UO2+x – might be encountered at various stages of the nuclear fuel cycle if oxidative conditions are met; the impact of physical property changes upon stoichiometry should therefore be properly assessed to ensure safe and reliable operations. These physical properties are intimately linked to the arrangement of atomic defects in the crystalline structure. The first paper evaluates the evolution of defect concentration with environment parameters – oxygen partial pressure and temperature by means of a point defect model, with reaction energies being derived from EP based atomic scale simulations. Ultimately, results from the point defect model are discussed, and compared to experimental measurements of stoichiometry dependence on oxygen partial pressure and temperature. Such investigations will allow for future discussions about the solubility of different fission products and dopants in the UO2 matrix at EP level.While the first paper answers the central question regarding the dominating defects in non-stoichiometry in UO2, the focus of the second paper was on the EP prediction of the material properties, notably the lattice parameter of Am, Np containing U and Pu MOX as a function of atomic fractions.The configurational space of a complex U1-y-y’-y’’PuyAmy’Npy’’O2 system, was assessed via Metropolis-Monte Carlo techniques. From the predicted configuration, the relaxed lattice parameter of Am, Np bearing MOX fuel was investigated and compared with available literature data. As a result, a linear behaviour of the lattice parameter as a function of Am, Np content was observed, as expected for an ideal solid solution. These results will allow to support and increase current knowledge on Gen-IV fuel properties, such as melting temperature, for which preliminary results are presented in this thesis, and possibly thermal conductivity in the future. / Doctorat en Sciences de l'ingénieur et technologie / info:eu-repo/semantics/nonPublished