Charles University in Prague, Faculty of Pharmacy in Hradec Králové Department of Pharmaceutical Technology Consultant: Mgr. Pavel Ondrejček, Ph.D. Student: Žofie Trpělková Title: A study of a compaction process of microcrystalline cellulose pellets This work is aimed at the comparison of two types of microcrystalline cellulose (Comprecel 102 a Avicel PH-200) with two types of pellets made of microcrystalline cellulose (Cellets 100 a Cellets 200). Important properties for the compaction into tablets were analyzed in these materials. The particle size distribution, the content of moisture, the bulk and tapped density, the flowability, the angle of repose and the Hausner ratio were evaluated. Furthermore, the compaction process was described by using the force displacement method and the three-exponential equation. Finally, the radial strength and the friability of tablets prepared by using two different compaction forces were evaluated. The results proved that both types of pellets have much better flow properties than powdered microcrystalline celluloses. This is primarily caused by the narrow particle size distribution, higher bulk and tapped density and the significantly smoother surface of pellets. Better flow properties of the pellets also influenced the parameters of the force-displacement...

Charles University in Prague, Faculty of Pharmacy in Hradec Králové Department of: Pharmaceutical technology Consultant: Mgr. Svačinová Petra, Ph.D. Student: Hamplová Kateřina Title of Thesis: The influence of the dwell time on the parameters of the stress relaxation test for microcrystalline cellulose and starch. This thesis is focused on the viscoelastic properties of pharmaceutical excipients and the tensile strength of tablets. The theoretical part describes used materials. Microcrystalline cellulose and starch were used as fillers and magnesium stearate at concentration of 1% was used as lubricant. The stress relaxation test and its evaluation and utilization not only in pharmacy is described as well as the tensile strength of tablets. The experimental part deals with the viscoelastic properties of used materials and their mixtures with lubricant. These properties were evaluated using the stress relaxation test. At maximum compression force of 10 kN the length of dwell time was changed (60 s, 120 s, 180 s, 240 s, 300 s, 360 s, 420 s, 480 s, 540 s, 600 s). For derived parameters of elasticity A1-3 and plasticity P1-3 the dependence on the length of dwell time was evaluated. Parameter A1 increases with increasing dwell time for all substances. For parameters A2, A3, the dependence on the dwell...

The goal of this thesis was to invent and perform a testing protocol, witch can detect connective tissue mechanical and structural properties simultaneously in patients with clubfoot. Based on literature findings, it was presumed that connective tissue differ between medial and lateral side of foot. Because of low availability of specimen, it was important to draw and mention crucial alterations of testing protokol, for minimization of failed measurments. For reasons above, two specimens diveded into two samples was used for experiment. Described and discused methodics may enable of reader to insigt to drawbacks of this examination. For usability of this protocol, a setting and testing of few hypotheses was performed. One axis tensial testing with SHG microscopy examination was used in combination for experiment. One of the main result was finding, that structural differencies witch were expected, were not distinctive in samples in untensioned state. But, distingtive differencies may be drawed in tensioned samples. This differences for low number of specimen, cannot show any tendence. Results of tensial testing showed, that samples from medial side of foot can have higher toughness and higher fragility. For future acquisition of tendencies in specimen differencies, it is important to set particular...

This diploma thesis is focused on behavior of cement concrete at high temperatures. The theoretical part describes processes, which take place in concrete at thermal loading and effect of this thermal load to mechanical and physical properties of concrete. Also there was described recommendation for testing physical and mechanical of concrete at high temperatures according to RILEM TC. In experimental part mixes were made with greywacke aggregate, amphibolite aggregate and with the addition of polypropylene fibers or cellulose fibers. In these mixes was determined the effect of high temperatures on the density of concrete, compressive strength of concrete and thermal strain of concrete. Further there was tested addition of 2 kg/m3 polypropylene fibers to concrete with basalt aggregate and siliceous aggregate and influence of these fibers to density of concrete, compressive strength of concrete and dynamic modulus of elasticity.

Title: Mathematical analysis and computer simulations of deformation of nonlinear elastic bodies in the small strain range. Author: Vojtěch Kulvait Department: Mathematical Institute of Charles University Supervisor: prof. RNDr. Josef Málek, CSc., Dsc. Abstract: Implicit constitutive theory provides a suitable theoretical framework for elastic materials that exhibit a nonlinear relationship between strain and stress in the range of small strains. We study a class of power-law models, where the nonlinear dependence of strain on the deviatoric part of the stress tensor and its trace are mutually separated. We show that these power-law models are capable to describe the response of a wide variety of beta phase titanium alloys in the small strain range and that these models fit available experimental data exceedingly well. We also develop a mathematical theory regarding the well-posedness of boundary value problems for the considered class of power-law solids. In particular, we prove the existence of weak solutions for power law exponents in the range (1, ∞). Finally, we perform computer simulations for these problems in the anti-plane stress setting focusing on the V-notch type geometry. We study the dependence of solutions on the values of power law exponents and on the V-notch opening angle. We achieve...

Cílem této práce je prezentovat metody pro akceleraci výpočtů stínů a osvětlení.  Práce se zabývá akcelerací na vzorek přesných stínů pomocí stínových těles na různých platformách. Obsahem práce je také zvýšení přesnosti stínových map a zvýšení přesnosti osvětlování scény s mnoha světly.

The thesis deals with the issue of suspension of the 5th passenger car door. The introductory part deals with the possibilities of mounting the 5th passenger car door. In the next part, a HDS hinge was selected, which is further solved using a numerical and experimental method. Aluminium alloy was used on this HDS hinge to reduce weight. In the first step, a technical experiment was performed on the existing state (steel) and a strain-strain analysis was performed. Based on the stress-strain analysis of the material change variant without structural change, unsatisfactory results were obtained. After that, design changes were proposed such as increasing the thickness of the tube wall in the Creo program, and this variant was also subjected to a stress-strain analysis using the numerical modelling. Comparison of the results was based on the values of elastic deformation and equivalent stress. Finally, the thesis dealt with the manufacturability of the proposed component within which, a technical experiment was carried out.

Práce je zaměřena na výzkum nové struktury umožňující charakterizaci fyzikálních vlastností grafenu při přesně řízených podmínkách. Návrh spojuje MEMS piezoelektrický rezonátor spolu s Hall Bar/FET strukturou. Tento přístup umožňuje měnit vlastnosti grafenu odděleně nebo společně dvěma metodami. Mechanický způsob je založen na relativní deformaci způsobené rezonátorem, na kterém je umístěna grafenová monovrstva. Navrhovaná struktura umožňuje měřit vlastnosti grafenu vyvolané pouze změnou mechanického pnutí a frekvencí nucených kmitů bez vlivu vnějšího elektrického pole. Druhý přístup přidává možnost ovládat fyzikální vlastnosti grafenu pomocí elektrického pole FET struktury. Tato technika využívá grafenovou monovrstvu jako laditelný sensor pro molekulární detekci. Měření koncentrace v jednotkách ppb není konstrukčně ničím limitováno. Realizované frekvenčně laditelné piezoelektrické MEMS rezonátory s monovrstvou grafenu budou využitelné v mnoha oblastech pro detekci na molekulové úrovni. Výsledné struktury budou vyrobeny v souladu s požadavky na bio- a CMOS kompatibilitu.

This thesis is focused on processing of pure magnesium by high pressure torsion method (HPT). This process belongs to the group of intensive plastic deformation methods (SPD). SPD methods are in the centre of scientific interest for several decades. Theoretical part of this thesis puts an effort to summarize basic knowledge and principles of SPD methods with extra focus on method HPT. As theoretical part continues magnesium as technical material is presented. Influence of SPD on use and properties of pure magnesium is then presented. This trend is further developed in effort to describe the effect of individual HPT process variables on the properties of pure magnesium and its alloys. Focus of practical part of this thesis is in influence of number of revolutions. Samples were processed at 1/8, 1/4, 1/2, 1, 4 and 8 turns at room temperature. Speed of process was 1rpm and applied pressure was 6 GPa. The structure of commercially pure magnesium prepared by casting and moulding were observed with focus on differences caused by input material. The structure was observed by both light microscopy and back scattered electron diffraction (EBSD), focusing on structure development, grain size and grain orientation. Compared to other works on similar topic, the emphasis here is on observing the microhardness on the vertical edge of the sample. The hardness shows a steep increase right after 1/8 of a turn. With increasing number of turns gradual homogenization of microhardness is presented accompanied by slight decrease in microhardness. No trend in microhardness relative to the distance from anvil has occurred. Structure observed with EBSD shows a bimodal character with larger grains oriented in the same direction. The three-point bending test didn’t end up as expected, and the approach to evaluation of magnesium-based HPT needs to be re-evaluated for future work. A three-point bending test was designed for the initial assessment of the basic mechanical properties of the material.

This Master‘s thesis is focused on theoretical study of twinning in magnetic shape memory alloys based on Ni2MnGa using ab initio calculations of electronic structure within the projector augmented wave method. In particular, the effect of increasing concentration of manganese at the expense of gallium was studied on total energy and stress profiles along different deformation paths in the (10-1)[101] shear system of non-modulated martensite. Further, this work deals with the effect of the concentration of manganese on the energy of planar fault caused by presence of partial dislocation due to motion of twin boundary. The results show that the shear modulus in studied shear system increases with the increasing concentration of manganese as well as energy barrier and deformation characteristics along shear deformation paths increases, which makes the shear more difficult in Mn-rich alloys. Increasing concentration of manganese also leads to rising the planar fault energy. All these effects can be responsible for lower mobility of twin boundaries in alloys with higher concentration of manganese.