Biodiesel and hydrotreated vegetable oil (HVO) are currently viewed by the transportation sector as the most viable alternative fuels to replace petroleum-based fuels. The use of biodiesel has, however, been limited by the deteriorative effect of biodiesel on rubber parts in automobile fuel systems. This work therefore aimed at investigating the degradation of acrylonitrile butadiene rubber (NBR) and fluoroelastomers (FKM) on exposure to biodiesel and HVO at different temperatures and oxygen concentrations in an automated ageing equipment and a high-pressure autoclave. The oxidation of biodiesel at 80 °C was promoted by an increase in the oxygen partial pressure, resulting in the formation of larger amounts of hydroperoxides and acids in the fuel. The fatty acid methyl esters of the biodiesel oxidized less at 150 °C on autoclave aging, because the termination reactions between alkyl and alkylperoxyl radicals dominated over the initiation reactions. HVO consists of saturated hydrocarbons, and remained intact during the exposure. The NBR absorbed a large amount of biodiesel due to fuel-driven internal cavitation in the rubber, and the uptake increased with increasing oxygen partial pressure due to the increase in concentration of oxidation products of the biodiesel. The absence of a tan δ peak (dynamical mechanical measurements) of the bound rubber and the appearance of carbon black particles devoid of rubber suggested that the cavitation was caused by the detachment of bound rubber from particle surfaces. A significant decrease in the strain-at-break and in the Payne-effect amplitude of NBR exposed to biodiesel was explained as being due to the damage caused by biodiesel to the rubber-carbon-black network. During the high-temperature autoclave ageing, the NBR swelled less in biodiesel, and showed a small decrease in the strain-at-break due to the cleavage of rubber chains. The degradation of NBR in the absence of carbon black was due only to biodiesel-promoted oxidative crosslinking. The zinc cations released by the dissolution of zinc oxide particles in biodiesel promoted reduction reactions in the acrylonitrile part of the NBR. Heat-treated star-shaped ZnO particles dissolved more slowly in biodiesel than the commercial ZnO nanoparticles due to the elimination of inter-particle porosity by heat treatment. The fuel sorption was hindered in HVO-exposed NBR by the steric constraints of the bulky HVO molecules. The extensibility of NBR decreased only slightly after exposure to HVO, due to the migration of plasticizer from the rubber. The bisphenol-cured FKM co- and terpolymer swelled more than the peroxide-cured GFLT-type FKM in biodiesel due to the chain cleavage caused by the attack of biodiesel on the double bonds formed during the bisphenol curing. The FKM rubbers absorbed biodiesel faster, and to a greater extent, with increasing oxygen concentration. It is suggested that the extensive biodiesel uptake and the decrease in the strain-at-break and Young’s modulus of the FKM terpolymer was due to dehydrofluorination of the rubber by the coordination complexes of biodiesel and magnesium oxide and calcium hydroxide particles. An increase in the CH2-concentration of the extracted FKM rubbers suggested that biodiesel was grafted onto the FKM at the unsaturated sites resulting from dehydrofluorination. / <p>QC 20170227</p>

Der Fokus dieser Dissertation lag in der Untersuchung des Potentials von Aluminium-chlorofluorid (ACF) als Katalysator für die Synthese von fluorierten Verbindungen. Insbesondere die C−F-Aktivierung von verschiedenen polyfluorierten Stoffen wurde untersucht, welches die Effizienz des festen Lewis-Säure-Katalysators für diesen Reaktionstyp zeigte. Das potente Treibhausgas 2-Chlor-1,1,1,2-tetrafluorpropan wurde erfolgreich in das dehydrofluorierte Produkt. Weiterhin wurden Umsetzungen von Pentafluorpropan-Isomeren wie z.B. 1,1,1,3,3-Pentafluorpropan, 1,1,1,2,2-Pentafluorpropan und 1,1,1,2,3-Pentafluorpropan mit ACF als Katalysator untersucht. Es konnte gezeigt werden, dass die Aktivierung der primären CH2F-Gruppe in schnell stattfindet und dabei keine Wasserstoffquelle erfordert. Im Kontrast dazu, wurde für die Aktivierung von CF2-Gruppen eine Wasserstoffquelle wie etwa HSiEt3 benötigt und resultierte in der Bildung eines Produktgemischs. Alternativ wurden Hydrofluorierungsreaktionen von mehreren Substraten durch die Synthese und den Einsatz eines neuen Materials erreicht, welches auf der Immobilisierung von HF auf der Oberfläche von ACF beruht. Dieses HF-ACF wurde unter der Verwendung von vielfältigen Charakterisierungsmethoden umfassend untersucht. Die innere Struktur des Festkörpers, wurden mit MAS-NMR-Spektroskopie, FTIR, Inelastische Neutronenstreuung, XRD und Thermoanalyse analysiert Dadurch konnte gezeigt werden, dass eine geringfügige Reorganisation des bulks zu einer besser geordneten Matrix und die Bildung einer mit der ACF-Oberfläche wechselwirkenden Polyfluorid-Struktur vorliegt. Zur Bestimmung der Oberflächengröße wurde das BET-Modell genutzt und zur Analyse der Porengröße wurde die NLDFT verwendet. Abschließend wurden verschiedene Probeverbindungen an der Oberfläche des HF-ACFs adsorbiert um die Azidität der Oberfläche zu bestimmen und es konnte gezeigt werden, dass eine signifikante Reduktion der Lewis- und Brønsted-Azidität vorliegt. / The main focus of this thesis lies in the study of the potential of aluminum chlorofluoride (ACF) as a catalyst for the synthesis of fluorinated compounds. In particular, C−F bond activations of various polyfluorinated compounds were studied, showing the efficiency of this solid Lewis acid catalyst for this type of reaction. The potent greenhouse gas 2-chloro-1,1,1,2-tetrafluoropropane was successfully transformed into the dehydrofluorination product 2-chloro-3,3,3-trifluoropropene under mild conditions. Similarly, transformation of pentafluoropropane isomers, such as 1,1,1,3,3-pentafluoropropane, 1,1,1,2,2- pentafluoropropane and 1,1,1,2,3-pentafluoropropane was also investigated using ACF as a catalyst. It was evidenced that the primary CH2F group present in 1,1,1,2,3-pentafluoropropane was easily activated without the need for a hydrogen source. In contrast, to activate CF2 groups, a hydrogen source such as HSiEt3 was required, generating a variety of products. Alternatively, successful hydrofluorination reactions of several substrates were conducted by synthesizing a new material, based on the loading of hydrogen fluoride (HF) at the surface of ACF. This HF-loaded ACF was deeply studied using a wide range of characterization methods. For the bulk, MAS NMR spectroscopy, Fourier Transform Infrared spectroscopy (FTIR), Inelastic Neutron Scattering (INS), Powder X-Ray Diffraction (P-XRD), and thermoanalysis were performed, revealing a slight reorganization of the bulk towards a better-ordered matrix and the formation of polyfluoride structure interacting with the surface of ACF. The BET model was used for the surface area determination, and the pore size analysis was established using the non local density functional theory (NLDFT). Finally, various probe molecules were adsorbed at the surface of HF-loaded ACF to determine the acidity of the surface, revealing a significantly reduced Lewis and Brønsted acidity.