Indiana University-Purdue University Indianapolis (IUPUI) / Recent theoretical and experimental studies, suggest that Carbon nanotubes are 10-100 times higher than the strongest steel at a fraction of the weight. There are two main types of CNTs that can have high structural perfection. Single-walled nanotubes (SWNTs) consist of a single graphite sheet seamlessly wrapped into a cylindrical tube. Multi-walled carbon nanotubes (MWNTs) comprise an array of such nanotubes concentrically nested like rings of a tree trunk. Denture base acrylics have been reinforced with different materials with limited success. No single reinforced material has showed a great statistical difference in mechanical improvement. The goal of this investigation was to study the effects of Single Walled Carbon Nanotubes reinforcement on the mechanical properties of commercially available denture base PMMA. Denture Base material was reinforced with Single-walled Carbon Nanotubes (SWNTs) at dispersion of 0.25 wt % (group 1), 0.50 wt % (group 2), 0.75 wt % (group 3) and 0.0 wt % (group 4, control). Samples from each group were evaluated for microhardness, flexural strength, flexural modulus, and fracture toughness. The samples were tested in two conditions, as manufactured (dry) and after storing at 37 C for 7 days (wet). Data from four experiments was analyzed by ANOVA. All control sample values were in the range of acceptance compared with previous studies. Higher values were obtained for the control groups for flexural strength and modulus compared with the experimental samples. (p < 0.05) There was no statistical difference regarding fracture toughness between control and experimental groups. A statistical difference was observed in Hardness. The experimental group showed higher values under compression.

No description available.

Objectives. Polyamide-12 (PA) is a flexible material suited for denture bases and clasping. This study investigated its potential aging effects with a focus on surface roughness, color stability, and elasticity. Methods. PA specimens (Valplast) of 40 × 10 × 2mm and equally measuring PMMA specimens (Palapress) as control were fabricated. Color changes after storage in air, water, coffee, and red wine (n = 10) were measured using the CIE L*a*b color specification. Elasticity after thermocycling (1000, 3000, and 7000 cycles, n = 15) was measured by three-point bending testing. Mean surface roughness (Ra) was determined after storage in the liquids mentioned above and thermocycling (n = 10). Results. Tukey’s HSD test (P < 0.05) revealed statistically significant color changes of PA in red wine (ΔE = 4.27 after 12 days, EΔE = 6.90 after 12 days) and coffee (ΔE = 3.93 after 36 days) but no color changes in PMMA. Elastic modulus of PA was 845MPa and not affected by thermocycling (Tukey’s HSD test, P > 0.81). Dry specimens showed significantly decreased elasticity (P < 0.001). Mean surface roughness (PA 0.20 μm, PMMA 0.28 μm) did not change significantly after thermocycling or storage (Mann-Whitney U-test, 0.16 < P < 0.65). Significance. PA exhibited a higher susceptibility to discoloration than PMMA. Neither surface roughness nor elasticity of PA was altered by artificial aging.

Chitosan is a cationic natural polymer that is widely used as a topical dressing in wound management. Temporary coatings of removable denture bases with chitosan might be useful as supportive treatment in oral medicine. The aim of this study was to analyze the thickness, uniformity, and adhesive strength of chitosan coatings on simulated denture bases made from polymethyl methacrylate (PMMA). According to a standardized protocol, 20 PMMA cylinders (13 mm diameter, 5 mm in height) as well as 20 cubes (a = 25 mm) with intaglio U-shaped profiles were manufactured to simulate average sized alveolar ridges. Cylinders as well as cubes were divided into four test series with n = 5 each. After sandblasting with silica-modified alumina, one frontal surface of the PMMA cylinders and the intaglio surfaces of the U-shaped profiles was coated with chitosan acetate solution according to the following protocols: one layer of 2% chitosan acetate solution (test series I), one layer of 4% chitosan acetate solution (test series II), two layers of 2% chitosan acetate solution (test series III), and two layers of 4% chitosan acetate solution (test series IV). After drying and neutralization with NaOH, each cube was cut transversely and the coating thickness across the U-shaped profile assessed with a light microscope. Adhesive strength was evaluated by simulated tooth brushing and the loss of chitosan coating was evaluated qualitatively. Statistical analysis used Friedman ANOVA test for dependent samples and Kruskal-Wallis test for independent samples, post-hoc Dunn’s test (p < 0.05), and binomial test (p = 0.05). The mean chitosan coating thicknesses in the depth of the U-profiles were 71 µm (test series I), 77 µm (test series II), 121 µm (test series III), and 517 µm (test series VI). The thickness continuously decreased with rising angulation of the U-profile side walls. In test series I, the chitosan coating thickness significantly dropped above a 30° angulation of the U-profile side walls. In test series II to IV, the chitosan thickness drop was not statistically significant at angulations of 30° and 60°, but was at 90° angulation of the U-profile side walls. Adhesion strength was rated fair to good and did not differ significantly among the four test series. The coating technique described revealed chitosan layers with overall good adhesion strength but differing thicknesses. Coatings with one or two layers of 4% chitosan acetate solution allowed a relatively uniform chitosan thickness and thus might be usable in oral medicine.

Chitosan is a cationic natural polymer that is widely used as a topical dressing in wound management. Temporary coatings of removable denture bases with chitosan might be useful as supportive treatment in oral medicine. The aim of this study was to analyze the thickness, uniformity, and adhesive strength of chitosan coatings on simulated denture bases made from polymethyl methacrylate (PMMA). According to a standardized protocol, 20 PMMA cylinders (13 mm diameter, 5 mm in height) as well as 20 cubes (a = 25 mm) with intaglio U-shaped profiles were manufactured to simulate average sized alveolar ridges. Cylinders as well as cubes were divided into four test series with n = 5 each. After sandblasting with silica-modified alumina, one frontal surface of the PMMA cylinders and the intaglio surfaces of the U-shaped profiles was coated with chitosan acetate solution according to the following protocols: one layer of 2% chitosan acetate solution (test series I), one layer of 4% chitosan acetate solution (test series II), two layers of 2% chitosan acetate solution (test series III), and two layers of 4% chitosan acetate solution (test series IV). After drying and neutralization with NaOH, each cube was cut transversely and the coating thickness across the U-shaped profile assessed with a light microscope. Adhesive strength was evaluated by simulated tooth brushing and the loss of chitosan coating was evaluated qualitatively. Statistical analysis used Friedman ANOVA test for dependent samples and Kruskal-Wallis test for independent samples, post-hoc Dunn’s test (p < 0.05), and binomial test (p = 0.05). The mean chitosan coating thicknesses in the depth of the U-profiles were 71 µm (test series I), 77 µm (test series II), 121 µm (test series III), and 517 µm (test series VI). The thickness continuously decreased with rising angulation of the U-profile side walls. In test series I, the chitosan coating thickness significantly dropped above a 30° angulation of the U-profile side walls. In test series II to IV, the chitosan thickness drop was not statistically significant at angulations of 30° and 60°, but was at 90° angulation of the U-profile side walls. Adhesion strength was rated fair to good and did not differ significantly among the four test series. The coating technique described revealed chitosan layers with overall good adhesion strength but differing thicknesses. Coatings with one or two layers of 4% chitosan acetate solution allowed a relatively uniform chitosan thickness and thus might be usable in oral medicine.

Objectives. Polyamide-12 (PA) is a flexible material suited for denture bases and clasping. This study investigated its potential aging effects with a focus on surface roughness, color stability, and elasticity. Methods. PA specimens (Valplast) of 40 × 10 × 2mm and equally measuring PMMA specimens (Palapress) as control were fabricated. Color changes after storage in air, water, coffee, and red wine (n = 10) were measured using the CIE L*a*b color specification. Elasticity after thermocycling (1000, 3000, and 7000 cycles, n = 15) was measured by three-point bending testing. Mean surface roughness (Ra) was determined after storage in the liquids mentioned above and thermocycling (n = 10). Results. Tukey’s HSD test (P < 0.05) revealed statistically significant color changes of PA in red wine (ΔE = 4.27 after 12 days, EΔE = 6.90 after 12 days) and coffee (ΔE = 3.93 after 36 days) but no color changes in PMMA. Elastic modulus of PA was 845MPa and not affected by thermocycling (Tukey’s HSD test, P > 0.81). Dry specimens showed significantly decreased elasticity (P < 0.001). Mean surface roughness (PA 0.20 μm, PMMA 0.28 μm) did not change significantly after thermocycling or storage (Mann-Whitney U-test, 0.16 < P < 0.65). Significance. PA exhibited a higher susceptibility to discoloration than PMMA. Neither surface roughness nor elasticity of PA was altered by artificial aging.