This thesis deals with modeling and produce of reconfigurable multi-band planar antennas, which allow electrical shifting of frequency band. After antennas simulation with PIN diode and FET switch in a commercial program CST MW, another step is to optimize the antenna for a new substrate. The next step was to produce antennas. Finally, the optimized antennas are compared with the measurement on experimental antennas.

Master's thesis is focused on designing optical converter for EMC measurement transfering signal through noisy enviroment. First part contains analysis of electromagnetic interference and its coupling and measurement, especially types of probes for interference maesurement. Next part passing through designing of optoelectric and electrooptic converter with digital intensity modulation. Last part is about realization of optical converter.

Oblast problémů, ze kterých konkrétní téma projektu vychází, zahrnuje současnou globální transformaci zdrojů energie a jejich dodávek se zvláštní pozorností na obnovitelné zdroje energie. Důraz je kladen zejména na hodnoty jež přináší produkt určený k užívání ve veřejných prostorách. Autorovým zadáním bylo navrhnout osvětlovací jednotku nezávislou na vnějším zdroji napájení. Cílem návrhu je přehodnotit způsob, jakým jsou dnes technologie využívání sluneční a větrné energie běžně používány, a navrhnout řešení přinášející nové vlastnosti a užitné hodnoty pro přímého uživatele i celou společnost. Autor přináší návrh produktu jenž je reakcí na současné globální hrozby a příležitosti. Výsledkem projektu je návrh pouliční lampy kombinující fotovoltaický článek a větrnou turbínu s cílem získat elektrickou energii jež je dočasně akumulována a následně dodávána svítidlu. V návrhu je kladen důraz na požadavky ergonomie a estetickou hodnotu produktu. Navržené řešení znamená finanční přínos z hlediska šetření neobnovitelnými zdroji energie a případnými finančními výhodami pro investora plynoucími z provozování veřejného osvětlení. Pouliční lampa nezávislá na vnějším zdroji napájení má navíc menší negativní dopad na životní prostředí a představuje technologie využívání větrné a solární energie v přívětivé a nerušivé podobě.

The thesis deals with the application of laser beams for examination of material properties. The properties being examined are quality of surface finish and transmissivity of materials in the optical portion of the electromagnetic spectrum. A measuring device containing laser diodes as a source of laser beam and photodiodes for evaluation of examined phenomena serves for examination of both properties. Conversion of the signal to digital quantity and its further processing take place in a microcontroller. The data is then sent via a serial bus and a converter to a computer, where it may be saved in a user program and where the user can work with them later. The thesis contains results of reflectivity measurement of a set of metal samples with different surface finish. Transmissivity measurement was applied on a set of optical filters.

This thesis deals with the analysis of solar cells by photoluminescence method. Photoluminescence method is based on the excitation of luminescence radiation of the solar cell material by an external excitation light source. This method can detect various types of defects in the material solar cells. The main objective is the design and realization of a measuring system defects of solar cells, which is based on this method. For excitation of luminescence is used LED array. For the detection of luminescence is used CCD camera with IR optical filter. To filter out the excitation light radiation is used disc screen and optical interrupter. The parameters and options of this measuring system are verified and characterized by test measuring for example the achievable rotation speed of screen and response of optical interrupter. At the end is tested detection of luminescence radiation of solar cells in the measuring system. The measured images are compared with the method of electroluminescence.

The doctoral thesis deals with diagnostics of local defects in PN junctions and brings new information about microplasma noise behaviour and its usage for the temperature changes detection inside PN junctions. Defects in PN junctions are the source of microplasma noise. There were deviations observed in microplasma noise from the common known rectangle shape pulses during the measurements. These deviations were correlated with the temperature change directly in the defect area and in the defect area surroundings. Generation and recombination coefficients are commonly thought to be constant. However, these coefficients were observed to be not stable with time and this effect is explained in this work. The doctoral thesis then focuses on the PN junction parameters determination in the case when it is not possible to define unambiguously whether it is abrupt or linearly graded PN junction. The most significant parameters which are to be determined are barrier capacity, diffusion voltage and depleted area width in dependence on the voltage. The correlation between local avalanche discharge in PN junction and negative differential resistance appearance on VA characteristics of reverse-biased diode was qualitatively verified. The last important point in the work is computer modelling of temperature behaviour in the defect area and its surroundings during local avalanche breakdown. Thus the method of real diodes heating area parameters determination was introduced.

This diploma thesis deals with the influence of long fiber optic paths on the polarization state of light and their use for powering polarization sensors. The aim of the diploma thesis was to design the arrangement of optical fiber components so that the polarization properties of light at the end of the path are further usable for sensory purposes. Four partial measurements with a long path (in a laboratory setting, laying in the ground, on a curtain, under the influence of external influence) and one measurement without a path under the influence of external influence were designed. The overall measurement results demonstrate that for the functional power supply of long-distance sensor systems, an existing single-mode fiber can be used (laid by laying in the ground), into which a light source for a given sensor system would be multiplexed. In the discussion, all types of measurements are analyzed and compared with each other. Finally, the overall result is summarized and applications are described in which such a sensor system could be used.

In last years phenomena of wireless communication technologies became a primary interest of big development laboratories whole world. Domain of point to point links which are realized by laser technology with narrow beam divergence and very sensitive photo-detectors is ordinarily used these days. This trend of using light waves as carrier medium turned interests of scientist to the sphere of wide area networks which is domain of wi-fi radio technologies. One of new trends in this sphere is also in-door free space optics. With expansion which leads to using LED's in everyday applications and with technological progress of last years, also grows tendency of most effective utilization of LED systems. The result of this effort is thought which considerate LED as source of artificial lighting and source of carrier medium for modulated signal. This kind of device must fulfill hygienic standards for illumination and also must be able to work with high frequency by which is signal modulated. These systems can provide links with sufficient capacity in order of hundred megabits.