In the past 15 years, many efforts were made to create functionalized artificial surfaces showing special anti-bacterial and anti-biofouling properties. Thereby, the topography of medical relevant materials plays an important role. However, the targeted fabrication of promising surface structures like hole-, lamella- and pyramid-like patterns with feature sizes in the sub-micrometer range in a one-step process is still a challenge. Optical and e-beam lithography, molding and selfassembly layers show a great potential to design topographies for this purpose. At the same time, most of these techniques are based on sequential processes, require masks or molds and thus are very device relevant and time consuming. In this work, we present the Direct Laser Interference Patterning (DLIP) technology as a capable method for the fast, flexible and direct fabrication of periodic micrometer- and submicrometer structures. This method offers the possibility to equip large plain areas and curved devices with 1D, 2D and 3D patterns. Simple 1D (e.g. lines) and complex 3D (e.g. lamella, pillars) patterns with periodic distances from 0.5 μm to 5 μm were fabricated on polymeric materials (polyimide, polystyrene). Subsequently, we characterized the adhesion behavior of Staphylococcus epidermidis and S. aureus bacteria under in vitro and in vivo conditions. The results revealed that the topographies have a significant impact on bacteria adhesion. On the one side, one-dimensional line-like structures especially with dimensions of the bacteria enhanced microbe attachment. While on the other hand, complex three-dimensional patterns prevented biofilm formation even after implantation and contamination in living organisms.

Surfaces equipped with periodic patterns with feature sizes in the micrometer, submicrometer and nanometer range present outstanding surface properties. Many of these surfaces can be found on different plants and animals. However, there are few methods capable to produce such patterns in a one-step process on relevant technological materials. Direct laser interference patterning (DLIP) provides both high resolution as well as high throughput. Recently, fabrication rates up to 1 m²·min-1 could be achieved. However, resolution was limited to a few micrometers due to typical thermal effects that arise when nanosecond pulsed laser systems are used. Therefore, this study introduces an alternative to ns-DLIP for the fabrication of multi-scaled micrometer and submicrometer structures on nickel surfaces using picosecond pulses (10 ps at a wavelength of 1064 nm). Due to the nature of the interaction process of the metallic surfaces with the ultrashort laser pulses, it was not only possible to directly transfer the shape of the interference pattern intensity distribution to the material (with spatial periods ranging from 1.5 μm to 5.7 μm), but also to selectively obtain laser induce periodic surface structures with feature sizes in the submicrometer and nanometer range. Finally, the structured nickel sleeves are utilized in a roll-to-roll hot embossing unit for structuring of polymer foils. Processing speeds up to 25 m·min-1 are reported.

In this work, the mesh-free smoothed particle hydrodynamics (SPH) method is applied in the modelling of the direct laser interference patterning (DLIP) of metal surfaces. The DLIP technique allows the fabrication of periodic microstructures on technical surfaces using nanosecond laser pulses. Here, the interference of two coherent partial beams with a sinusoidal energy density distribution of the interference pattern is concerned, which is employed to generate line-like surface structures. However, the mechanisms effective during nanosecond pulsed DLIP of metals are not yet fully understood. The physical phenomena occurring due to the interaction of laser radiation with metallic materials are first considered and the governing differential equations are stated. The fundamentals of the SPH method and the approaches to the numerical treatment of the conservation equations are presented. Physical processes relevant to the modelling of laser material processing are solved by suitable SPH techniques, i.e. the approximations are verified with respect to test problems with analytical or known numerical solutions. Consequently, the SPH method is used to devise a thermal model of the DLIP process, considering the absorption of the laser radiation, the heat conduction into the workpiece and the latent heat of involved phase changes. This model is extended to compute the melt pool convection during DLIP, which is driven by surface tension gradients due to temperature gradients. For this purpose, an incompressible SPH (ISPH) method is used, representing a novel approach to the modelling of the laser-induced melt pool flow. The numerical model is employed to perform simulations of DLIP on metal substrates. Firstly, the thermal simulation of the single pulse patterning of stainless steel is in good agreement with experimental results. The application of DLIP to stainless steel and aluminium is then simulated by the comprehensive model including the melt pool flow. Moreover, this model is further extended to consider the non-linear temperature dependence of surface tension, as in liquid steel in the presence of a surface active element. The simulation results reveal a distinct behaviour of stainless steel and aluminium substrates. A markedly deeper melt pool and considerable velocity magnitudes of the thermocapillary convection at the melt surface are computed for DLIP of aluminium. In contrast, the melt pool flow is less pronounced during DLIP of stainless steel, whereas higher surface temperatures are predicted. Hence the Marangoni convection is a conceivable effective mechanism during the structuring of aluminium at moderate energy density. The different character of the melt pool convection during DLIP of stainless steel and aluminium is corroborated by experimental observations. Furthermore, the simulations for stainless steel with different sulphur content indicate distinct melt pool flow patterns and support the explanation of the microstructures found after DLIP experiments. The role of vapourisation and the induced recoil pressure in the microstructure evolution due to DLIP on metal substrates at elevated fluences could be prospectively investigated. In this regard, the consideration of the melt pool surface deformation in the ISPH algorithm, and particularly a suitable pressure boundary condition, is required.:I The research problem 1 Motivation 2 Modelling of laser material processing 2.1 Interaction of laser radiation with materials 2.1.1 Absorption of laser radiation 2.1.2 Heat conduction and phase change 2.1.3 Molten pool convection 2.1.4 Vapourisation regime 2.2 Mathematical modelling of laser material interaction 2.2.1 Conservation equations in Lagrangian formulation 2.2.2 Influence of surface tension 3 State of the art in laser microprocessing and the SPH method 3.1 Laser microprocessing 3.2 Simulation of direct laser interference patterning 3.3 The mesh-free smoothed particle hydrodynamics method 3.3.1 Fundamental approximations and kernel function 3.3.2 Particle distribution and interaction length 3.3.3 Approximation of derivatives 3.3.4 Treatment of boundaries 3.3.5 Neighbourhood search 3.4 Numerical modelling of laser material processing by SPH II SPH model development for direct laser interference patterning 4 SPH modelling of heat transfer and fluid flow 4.1 Solution of the heat diffusion equation 4.2 Formulation of equations governing fluid flow 4.2.1 Equation of continuity 4.2.2 Approximation of pressure gradient term 4.2.3 Treatment of viscosity 4.3 Weakly compressible SPH method for solving fluid flow 4.3.1 Particle motion 4.3.2 Time integration 4.3.3 Time step criteria 4.4 Incompressible SPH method for solving fluid flow 4.4.1 Time integration 4.4.2 Discrete incompressible SPH algorithm 4.4.3 Time step criteria 4.5 Simulation of thermal fluid flow using ISPH 4.5.1 Semi-implicit time integration 4.5.2 Solution of the pressure Poisson equation 5 Verification of the SPH implementation 5.1 Transient heat conduction in laser-irradiated plate 5.1.1 Problem description 5.1.2 Dimensionless formulation 5.1.3 Numerical solution and results 5.2 Viscous flow 5.2.1 Couette flow 5.2.2 Poiseuille flow 5.3 Thermal convection 5.3.1 Natural convection in a square cavity 5.3.2 Rayleigh--Marangoni--Bénard convection in liquid aluminium 6 SPH model of direct laser interference patterning 6.1 Characteristics of the process 6.2 Thermal model 6.2.1 Non-dimensionalisation 6.2.2 Numerical solution of governing equation 6.2.3 Verification of the computation 6.2.4 Numerical test 6.3 Thermofluiddynamic model 6.3.1 Non-dimensionalisation 6.3.2 Numerical solution of governing equations 6.3.3 Discretisation 6.3.4 Resolution independence study 7 SPH simulation of direct laser interference patterning 7.1 Thermal model 7.1.1 DLIP experiments on stainless steel substrates 7.1.2 Thermal simulation of DLIP on steel substrate 7.2 Thermofluiddynamic model 7.2.1 Material properties and simulation parameters 7.2.2 Numerical results for steel substrate 7.2.3 Numerical results for aluminium substrate 7.2.4 Discussion and comparison with experiments 7.3 Extended thermofluiddynamic model 7.3.1 Model parameters 7.3.2 Influence of sulphur content on DLIP of stainless steel 8 Conclusions and outlook Bibliography / In dieser Arbeit wird die direkte Laserinterferenzstrukturierung (Direct Laser Interference Patterning, DLIP) von Metallen mit der netzfreien Smoothed Particle Hydrodynamics (SPH) Methode modelliert. Das DLIP-Verfahren ermöglicht die Fertigung periodischer Mikrostrukturen auf technischen Oberflächen mit Nanosekunden-Laserpulsen. Hier wird die Zweistrahlinterferenz mit einer sinusförmigen Energiedichteverteilung des Interferenzmusters behandelt, die linienförmige Oberflächenstrukturen erzeugt. Die bei der direkten Interferenzstrukturierung von Metallen mit Nanosekunden-Laserpuls wirksamen Mechanismen sind jedoch noch nicht verstanden. Die aufgrund der Wechselwirkung von Laserstrahlung mit metallischen Werkstoffen auftretenden physikalischen Phänomene werden zuerst betrachtet und die sie bestimmenden Differentialgleichungen angegeben. Die Grundlagen der SPH-Methode sowie deren Herangehensweisen an die numerische Behandlung der Erhaltungsgleichungen werden vorgestellt. Für die Modellierung der Lasermaterialbearbeitung relevante physikalische Vorgänge werden mittels geeigneter SPH-Ansätze gelöst, d. h. anhand von Testproblemen mit bekannter Lösung verifiziert. Das mit SPH zunächst erstellte thermische Modell des DLIP-Prozesses berücksichtigt die Absorption der Laserstrahlung, die Wärmeleitung im Werkstück und die Enthalpien der Phasenübergänge. Das Modell wird zur Berechnung der Schmelzbadströmung bei der DLIP-Anwendung, angetrieben von Oberflächenspannungsgradienten verursacht durch Temperaturgradienten, erweitert. Hierbei wird eine inkompressible SPH (ISPH) Methode eingesetzt, in der Simulation laserinduzierter Schmelzbäder ein neuartiger Ansatz. Mit dem numerischen Modell werden Simulationen des DLIP-Verfahrens für metallische Substrate durchgeführt. Die thermische Simulation der Strukturierung von Edelstahl stimmt gut mit einem Experiment überein. Weiterhin wird die Anwendung von DLIP auf Edelstahl und Aluminium mit dem thermofluiddynamischen Modell simuliert. Außerdem wird das Modell um eine nichtlinear temperaturabhängige Oberflächenspannung, wie sie für Stahlschmelze in Anwesenheit eines oberflächenaktiven Elements vorliegt, ergänzt. Die Simulationen zeigen ein verschiedenes Verhalten von Edelstahl und Aluminium. Bei der Strukturierung von Aluminium treten ein deutlich tieferes Schmelzbad und erhebliche Geschwindigkeitsbeträge der thermokapillaren Konvektion an der Schmelzeoberfläche auf. Hingegen ist die Strömung bei der DLIP-Anwendung auf Edelstahl schwächer ausgeprägt und höhere Oberflächentemperaturen werden erreicht. Die Marangoni-Konvektion ist daher ein wirksamer Schmelzeverdrängungsmechanismus bei der Strukturierung von Aluminium mit moderater Energiedichte. Die unterschiedliche Schmelzbadströmung für die beiden Werkstoffe wird durch experimentelle Beobachtungen bestätigt. In Abhängigkeit des Schwefelgehalts von Edelstahl zeigen Simulationen verschiedene Strömungsmuster im Schmelzbad und unterstützen die Erklärung experimentell festgestellter Mikrostrukturen. Die Untersuchung der Wirkung der Verdampfung und des induzierten Rückstoßdruckes auf die Strukturausbildung bei höheren Fluenzen erfordert die Berücksichtigung der Oberflächendeformation sowie eine geeignete Druckrandbedingung im ISPH-Algorithmus.:I The research problem 1 Motivation 2 Modelling of laser material processing 2.1 Interaction of laser radiation with materials 2.1.1 Absorption of laser radiation 2.1.2 Heat conduction and phase change 2.1.3 Molten pool convection 2.1.4 Vapourisation regime 2.2 Mathematical modelling of laser material interaction 2.2.1 Conservation equations in Lagrangian formulation 2.2.2 Influence of surface tension 3 State of the art in laser microprocessing and the SPH method 3.1 Laser microprocessing 3.2 Simulation of direct laser interference patterning 3.3 The mesh-free smoothed particle hydrodynamics method 3.3.1 Fundamental approximations and kernel function 3.3.2 Particle distribution and interaction length 3.3.3 Approximation of derivatives 3.3.4 Treatment of boundaries 3.3.5 Neighbourhood search 3.4 Numerical modelling of laser material processing by SPH II SPH model development for direct laser interference patterning 4 SPH modelling of heat transfer and fluid flow 4.1 Solution of the heat diffusion equation 4.2 Formulation of equations governing fluid flow 4.2.1 Equation of continuity 4.2.2 Approximation of pressure gradient term 4.2.3 Treatment of viscosity 4.3 Weakly compressible SPH method for solving fluid flow 4.3.1 Particle motion 4.3.2 Time integration 4.3.3 Time step criteria 4.4 Incompressible SPH method for solving fluid flow 4.4.1 Time integration 4.4.2 Discrete incompressible SPH algorithm 4.4.3 Time step criteria 4.5 Simulation of thermal fluid flow using ISPH 4.5.1 Semi-implicit time integration 4.5.2 Solution of the pressure Poisson equation 5 Verification of the SPH implementation 5.1 Transient heat conduction in laser-irradiated plate 5.1.1 Problem description 5.1.2 Dimensionless formulation 5.1.3 Numerical solution and results 5.2 Viscous flow 5.2.1 Couette flow 5.2.2 Poiseuille flow 5.3 Thermal convection 5.3.1 Natural convection in a square cavity 5.3.2 Rayleigh--Marangoni--Bénard convection in liquid aluminium 6 SPH model of direct laser interference patterning 6.1 Characteristics of the process 6.2 Thermal model 6.2.1 Non-dimensionalisation 6.2.2 Numerical solution of governing equation 6.2.3 Verification of the computation 6.2.4 Numerical test 6.3 Thermofluiddynamic model 6.3.1 Non-dimensionalisation 6.3.2 Numerical solution of governing equations 6.3.3 Discretisation 6.3.4 Resolution independence study 7 SPH simulation of direct laser interference patterning 7.1 Thermal model 7.1.1 DLIP experiments on stainless steel substrates 7.1.2 Thermal simulation of DLIP on steel substrate 7.2 Thermofluiddynamic model 7.2.1 Material properties and simulation parameters 7.2.2 Numerical results for steel substrate 7.2.3 Numerical results for aluminium substrate 7.2.4 Discussion and comparison with experiments 7.3 Extended thermofluiddynamic model 7.3.1 Model parameters 7.3.2 Influence of sulphur content on DLIP of stainless steel 8 Conclusions and outlook Bibliography

Increasingly compact and powerful light emitting diodes require the development of efficient optical diffusers to manage their lighting capability according to the required application. In this study, a cost-effective strategy is demonstrated for fabricating micro-structured polymethylmethacrylate (PMMA) diffusers for white light sources. By combining different laserbased processes, namely direct laser engraving (DLE), direct laser writing (DLW), and direct laser interference patterning (DLIP), periodic patterns are fabricated in stainless steel surfaces with line- and dot-like geometries with feature sizes ranging from 1.7 to 900 μm. The fabricated hierarchical geometries are transferred to PMMA surfaces by plate-to-plate hot embossing. The relationship between the surface topography and the white light scattering behavior is investigated by confocal and scanning electron microscopy combined with photospectroscopy and image processing of photographs. The triple-scaled hierarchical structures can increase the haze up to 76% in the visible spectrum, while keeping the total transmittance over 90%, as the flat surface.

Surface texturization of Transparent Conductive Oxides (TCOs) is a well-known strategy to enhance the light-trapping capabilities of thin-film solar cells and thus, to increase their power conversion efficiency. Herein, the surface modification of fluorine-doped tin oxide (FTO) using picosecond infrared direct laser interference patterning (DLIP) is presented. The surface characterization exhibits periodic microchannels, which act as diffraction gratings yielding an increase in the average diffuse transmittance up to 870% in the spectral range of 400–1000 nm. Despite the one dimensionality of the microstructures, the films did not acquire a significant anisotropic electrical behavior, but a partial deterioration of their conductivity is observed as a result of the removal of conductive material. This work proposes the feasibility of trading off a portion of the electrical conductivity to obtain a substantial improvement in the optical performance.