This master´s thesis focuses on the basic principles of the nonconventional technology of electrical discharge machining (EDM) with an emphasis on wire-cut electrical discharge machining performed in a mediumsized company. The thesis deals with manufacture of a belt pulley 75-8M-130, and checks of accuracy of wire-cut EDM machines. Following the study of the current status of electrical discharge machining in the engineering company, measures for assurance and increase of accuracy of wire-cut EDM machines are proposed.

My thesis is aimed at the application of wire electical discharge machining technology in the production of woodworking tools. All of this in the conditions of Vydona company. There is a theory of machining method plus a well-aranged division of cutter tools for wood in the introduction. The practical part describes in detail the procedur of cutting shaped plate out of tungsten carbide. As a result of the technical and at the same time the economic evaluation is an establishment of hourly rate for machine.

This master´s thesis deals with unconventional technology of wire electrical discharge machining. There are described the principles and essence of electrical discharge machining and the principles related to wire electrical discharge machining with emphasis on the application of this technology in terms of medium-sized engineering company. There is also described the complete assembly of technolgy wire cutting and machining on wire cutter Excetek V 650. Then in the work there are statistically evaluated parameters precision machined surfaces, specifically to the belt pulley 116-8M-130. At the end of the work there is the technical-economic evaluation that addresses the hourly cost of machining on wire cutter Excetek V 650.

Fir tree root forms are one way to retain turbine blades in turbine disks. These features are ruled surfaces that span the entire thickness of the disk and are usually machined by broaching. With increasing use of new heat resistant and difficult-to-machine materials, mechanical machining methods exhibit severe problems with tool wear and surface integrity. To mitigate these problems, thermal material removal processes such as Wire Electrical Discharge Machining (WEDM) are being considered in the aerospace industry. Developments in turbine design have led to a root form geometry in the form of an arc across the thickness of the disk in order to decrease the contact stress by increasing the contact area between blade and disk. A curved surface such as this cannot be produced by conventional WEDM as it is not a ruled surface. A novel WEDM process is being developed where an arc shaped curve is formed from an axially moving wire to allow for the production of such curved surfaces. / Thesis / Master of Applied Science (MASc) / Turbine blades are attached to turbine disks with specially shaped, straight slots called Fir Tree Root Forms (FTRF) that can be cut with broaching tools. Broaches wear out quickly because the disk is made of very difficult to cut material and the aerospace industry is starting to use Wire Electric Discharge Machining (WEDM), instead of broaching, to cut these slots since it can easily cut the material used. New turbine disk designs have curved slots, which can not be cut with a straight broach or wire, and a new process is therefore being developed which uses an arc-shaped wire to cut the desired curved shapes.

A MEMS-based micro-electro-discharge machining technique that is enabled by the actuation of micromachined planar electrodes defined on the surfaces of the workpiece is developed that eliminates the need of numerical control machines. First, the planar electrodes actuated by hydrodynamic force is developed. The electrode structures are defined by patterning l8-µm-thick copper foil laminated on the stainless steel workpiece through an intermediate photoresist layer and released by sacrificial etching of the resist layer. The planer electrodes are constructed to be single layer structures without particular features underneath. All the patterning and sacrificial etching steps are performed using dry-film photoresists towards achieving high scalability of the machining technique to large-area applications. A DC voltage of 80-140 V is applied between the electrode and the workpiece through a resistance-capacitance circuit that controls the pulse energy and timing of spark discharges. The parasitic capacitance of the electrode structure is used to form a resistance capacitance circuit for the generation of pulsed spark discharge between the electrode and the workpiece. The suspended electrodes are actuated towards the workpiece using the downflow of dielectric machining fluid, initiating and sustaining the machining process. Micromachining of stainless steel is experimentally demonstrated with the machining voltage of 90V and continuous flow of the fluid at the velocity of 3.4-3.9 m/s, providing removal depth of 20 µm. The experimental results of the electrode actuation match well with the theoretical estimations. Second, the planar electrodes are electrostatically actuated towards workpiece for machining. In addition to the single-layer, this effort uses double-layer structures defined on the bottom surface of the electrode to create custom designed patterns on the workpiece material. The suspended electrode is electrostatically actuated towards the wafer based on the pull-in, resulting in a breakdown, or spark discharge. This instantly lowers the gap voltage, releasing the electrode, and the gap value recovers as the capacitor is charged up through the resistor. Sequential pulses are produced through the self-regulated discharging-charging cycle. Micromachining of the stainless-steel wafer is demonstrated using the electrodes with single-layer and double-layer structures. The experimental results of the dynamic built-capacitance and mechanical behavior of the electrode devices are also analyzed.

A MEMS-based micro-electro-discharge machining technique that is enabled by the actuation of micromachined planar electrodes defined on the surfaces of the workpiece is developed that eliminates the need of numerical control machines. First, the planar electrodes actuated by hydrodynamic force is developed. The electrode structures are defined by patterning l8-µm-thick copper foil laminated on the stainless steel workpiece through an intermediate photoresist layer and released by sacrificial etching of the resist layer. The planer electrodes are constructed to be single layer structures without particular features underneath. All the patterning and sacrificial etching steps are performed using dry-film photoresists towards achieving high scalability of the machining technique to large-area applications. A DC voltage of 80-140 V is applied between the electrode and the workpiece through a resistance-capacitance circuit that controls the pulse energy and timing of spark discharges. The parasitic capacitance of the electrode structure is used to form a resistance capacitance circuit for the generation of pulsed spark discharge between the electrode and the workpiece. The suspended electrodes are actuated towards the workpiece using the downflow of dielectric machining fluid, initiating and sustaining the machining process. Micromachining of stainless steel is experimentally demonstrated with the machining voltage of 90V and continuous flow of the fluid at the velocity of 3.4-3.9 m/s, providing removal depth of 20 µm. The experimental results of the electrode actuation match well with the theoretical estimations. Second, the planar electrodes are electrostatically actuated towards workpiece for machining. In addition to the single-layer, this effort uses double-layer structures defined on the bottom surface of the electrode to create custom designed patterns on the workpiece material. The suspended electrode is electrostatically actuated towards the wafer based on the pull-in, resulting in a breakdown, or spark discharge. This instantly lowers the gap voltage, releasing the electrode, and the gap value recovers as the capacitor is charged up through the resistor. Sequential pulses are produced through the self-regulated discharging-charging cycle. Micromachining of the stainless-steel wafer is demonstrated using the electrodes with single-layer and double-layer structures. The experimental results of the dynamic built-capacitance and mechanical behavior of the electrode devices are also analyzed.

To survive in today's manufacturing environments companies must push the standards of accuracy and speed to the highest levels possible. Electro Discharge Machining (EDM) has been used for over 50 years and recent developments have seen the use of EDM become much more viable. The goal of this research is to produce and evaluate electrodes produced by different manufacturing methods. The use of electroforming and spray-metal deposition has only recently become viable methods of producing usable rapid tooling components. The speed and accuracy as well as the cost of manufacture play a vital role in the tool and mould manufacturing process. Electroforming and spray-metal deposition offer an alternate option to traditional machining of electrodes. Electroforming is one method of producing electrodes for EDM. The fact that electroforming can be used to produce multiple electrodes simultaneously gives it the advantage of saving on costs when multiple electrodes are needed. Spray-metal deposition offers another alternative that is much cheaper and relatively faster to manufacture. The used of these non-traditional manufacturing methods in this research are compared to the performance of traditional solid electrodes in terms of machining time, material removal rate, tool wear rates and surface roughness at several standard machining settings. The results of this research are presented in this thesis along with conclusions and comments on the performance of the different methods of electrode manufacture. The major findings of the research include the solid electrodes performed better than the electroformed electrodes in Material Removal Rate (MRR), Tool Wear Rate (TWR), and Surface Roughness (Ra) at all machine settings. However it was found that the production cost of the solid electrodes was six times that of the electroformed electrodes. The production of spray metal electrodes was unsuccessful. The electrode shell walls were not an even thickness and the backing material broke through the shell making them unusable. It is concluded that with further refinements and research, electroforming and spray metal processes will become an extremely competitive method in electrode manufacture and other rapid tooling processes.

A MEMS-based micro-electro-discharge machining technique that is enabled by the actuation of micromachined planar electrodes defined on the surfaces of the workpiece is developed that eliminates the need of numerical control machines. First, the planar electrodes actuated by hydrodynamic force is developed. The electrode structures are defined by patterning l8-µm-thick copper foil laminated on the stainless steel workpiece through an intermediate photoresist layer and released by sacrificial etching of the resist layer. The planer electrodes are constructed to be single layer structures without particular features underneath. All the patterning and sacrificial etching steps are performed using dry-film photoresists towards achieving high scalability of the machining technique to large-area applications. A DC voltage of 80-140 V is applied between the electrode and the workpiece through a resistance-capacitance circuit that controls the pulse energy and timing of spark discharges. The parasitic capacitance of the electrode structure is used to form a resistance capacitance circuit for the generation of pulsed spark discharge between the electrode and the workpiece. The suspended electrodes are actuated towards the workpiece using the downflow of dielectric machining fluid, initiating and sustaining the machining process. Micromachining of stainless steel is experimentally demonstrated with the machining voltage of 90V and continuous flow of the fluid at the velocity of 3.4-3.9 m/s, providing removal depth of 20 µm. The experimental results of the electrode actuation match well with the theoretical estimations. Second, the planar electrodes are electrostatically actuated towards workpiece for machining. In addition to the single-layer, this effort uses double-layer structures defined on the bottom surface of the electrode to create custom designed patterns on the workpiece material. The suspended electrode is electrostatically actuated towards the wafer based on the pull-in, resulting in a breakdown, or spark discharge. This instantly lowers the gap voltage, releasing the electrode, and the gap value recovers as the capacitor is charged up through the resistor. Sequential pulses are produced through the self-regulated discharging-charging cycle. Micromachining of the stainless-steel wafer is demonstrated using the electrodes with single-layer and double-layer structures. The experimental results of the dynamic built-capacitance and mechanical behavior of the electrode devices are also analyzed. / Applied Science, Faculty of / Electrical and Computer Engineering, Department of / Graduate

M.Ing. (Mechanical Engineering) / Please refer to full text to view abstract

This thesis talk about practical application of wire electrical discharge machining (WEDM), which belongs to electro-erosion machining methods. This thesis is focused on the production of cutting dies produced by company FOR MIX s.r.o. Trenčín. We can consider the cutting die as a typical product of company´s product program. In the practical part of this diploma thesis, there is detail of technological aspects and operating costs for wire electrical discharge machining technology in specific condition of company FOR MIX s.r.o.