In most man-made flight, vehicle control is achieved by deflecting flaps. However, in nature, morphing surfaces are found on both flying and swimming creatures. Morphing is used in nature because it is a more efficient form of control. This thesis investigates using morphing flaps to control a class of UAVs known as ducted fan vehicles. Specifically, this thesis discusses both the challenges and benefits of using morphing control surfaces. To achieve morphing, a piezoelectric device known as Macro Fiber Composites is used. These devices are embedded in the skin of the vehicles control surface, and when actuated, they cause the control surface to increase or decrease camber. This thesis describes experiments that were performed to investigate the performance of this type of actuator. Specifically, the actuation bandwidth of these devices is presented and compared to a servo. Results show that the morphing control surfaces can actuate at frequencies twice as high as a servo. / Master of Science

No description available.

The master’s thesis is dealt with the design of rebuilding of VUT 051 RAY which is equipped electric powerplant to twin-engine conception named VUT 051 RAY-DUO. In the thesis was verified the range of centre of gravity position of VUT 051 RAY-DUO then powerplant in ducted fan configuration was designed, performances of the airplane were appointed and controllability during fail one of the engines was analysed. The design of new powerplant was verified by strength analysis and then costing calculation was established.

Ducted fan vehicles possess a superior ability to maximize payload capacity while minimizing vehicle size. Their ability to both hover and fly at high speed is a key advantage for information-gathering missions, particularly when close proximity to a target is essential. However, the ducted fan's aerodynamic characteristics pose difficulties for stable vehicle flight and therefore require complex control algorithms. In particular, they exhibit a large nose-up pitching moment during wind gusts and when transitioning from hover to forward flight. Understanding ducted fan aerodynamic behavior and how it can be altered through flow control techniques are the two prime objectives of this work. This dissertation provides a new paradigm for modeling the ducted fan's nonlinear behavior and new methods for changing the duct aerodynamics using active flow control. Steady and piezoelectric synthetic jet blowing are employed in the flow control concepts and are compared. The new aerodynamic model captures the nonlinear characteristics of the force, moment, and power data for a ducted fan, while representing these terms in a set of simple equations. The model attains excellent agreement with current and legacy experimental data using twelve non-dimensional constants. Synthetic jet actuators (SJA) have potential for use in flow control applications in UAVs with limited size, weight, and power budgets. Piezoelectric SJAs for a ducted fan vehicle were developed through two rounds of experimental designs. The final SJA design attained peak jet velocities in the range of 225 ft/sec (69 m/s) for a 0.03â x 0.80â rectangular slot. To reduce the magnitude of the nose-up pitching moment in cross-winds, two flow control concepts were explored: flow separation control at the duct lip, and flow turning at the duct trailing edge using a CoandÄ surface. Both concepts were experimentally proven to be successful. Synthetic jets and steady jets were capable of modifying the ducted fan flow to reduce pitching moment, but some cases required high values of steady blowing to create significant responses. Triggering leading edge separation on the duct lip was one application where synthetic jets showed comparable performance to steady jets operating at a blowing coefficient an order of magnitude higher. / Ph. D.

Traditionally, the task of determining aircraft position and attitude for automatic control has been handled by the combination of an inertial measurement unit (IMU) with a Global Positioning System (GPS) receiver. In this configuration, accelerations and angular rates from the IMU can be integrated forward in time, and position updates from the GPS can be used to bound the errors that result from this integration. However, reliance on the reception of GPS signals places artificial constraints on aircraft such as small unmanned aerial vehicles (UAVs) that are otherwise physically capable of operation in indoor, cluttered, or adversarial environments. Therefore, this work investigates methods for incorporating a monocular vision sensor into a standard avionics suite. Vision sensors possess the potential to extract information about the surrounding environment and determine the locations of features or points of interest. Having mapped out landmarks in an unknown environment, subsequent observations by the vision sensor can in turn be used to resolve aircraft position and orientation while continuing to map out new features. An extended Kalman filter framework for performing the tasks of vision-based mapping and navigation is presented. Feature points are detected in each image using a Harris corner detector, and these feature measurements are corresponded from frame to frame using a statistical Z-test. When GPS is available, sequential observations of a single landmark point allow the point's location in inertial space to be estimated. When GPS is not available, landmarks that have been sufficiently triangulated can be used for estimating vehicle position and attitude. Simulation and real-time flight test results for vision-based mapping and navigation are presented to demonstrate feasibility in real-time applications. These methods are then integrated into a practical framework for flight in GPS-denied environments and verified through the autonomous flight of a UAV during a loss-of-GPS scenario. The methodology is also extended to the application of vehicles equipped with stereo vision systems. This framework enables aircraft capable of hovering in place to maintain a bounded pose estimate indefinitely without drift during a GPS outage.