"A small “spiralpole” antenna – the hybrid structure where one dipole wing is kept, but another wing is replaced by a coaxial single-arm spiral, is studied both theoretically and experimentally. Such a structure implies the implementation of an impedance-matching network (an inductor in series with a small dipole) directly as a part of the antenna body. The antenna impedance behavior thus resembles the impedance behavior of a small dipole in series with an extra inductance, which is that of the spiral. However, there are two improvements compared to the case when an equivalent small dipole is matched with an extra lumped inductor. First, the spiralpole antenna has a significantly larger radiation resistance – the radiation resistance increases by a factor of two or more. This is because the volume of the enclosing sphere is used more efficiently. Second, a potentially lower loss is expected since we only need a few turns of a greater radius. The radiation pattern of a small spiralpole antenna is that of a small dipole, so is the first (series) resonance. The Q-factor of the antenna has been verified against the standard curves. The antenna is convenient in construction and is appealing when used in conjunction with passive RFID tags such as SAW temperature sensors. "

The microwave near-field detection technique is of interest to many researchers for characterizing materials because of its high sensitivity. It is based on sensing buried objects by producing an evanescent field.The advantage of evanescent fields is their capability to interrogate electrically small objects. In the past, near-field probes have been designed to sense magnetic materials. For dielectric materials, a near-field probe that senses the permittivity of the materials is important. This work presents a novel design of a near-field probe that generates a dominant electric eld. The probe is an electrically small dipole measuring approximately 0.07?? in length operating at 216.3 MHz. The antenna is matched to a 50??? system using two chip inductors distributed symmetrically on the dipole. The numerical and measurement results show that the proposed design is highly sensitive and capable of sensing subsurface object. The proposed design is compact, lightweight and applicable for microwave applications.

"In the design of any antenna radiator, single or multi-element, a significant amount of time and resources is spent on impedance matching. There are broadly two approaches to impedance matching; the first is the distributed impedance matching approach which leads to modifying the antenna geometry itself by identifying appropriate degrees of freedom within the structure. The second option is the lumped element approach to impedance matching. In this approach instead of modifying the antenna geometry a passive network attempts to equalize the impedance mismatch between the source and the antenna load. This thesis introduces a new technique of impedance matching using lumped circuits (passive, lossless) for electrically small (short) non-resonant dipole/monopole antennas. A closed form upper-bound on the achievable transducer gain (and therefore the reflection coefficient) is derived starting with the Bode-Fano criterion. A 5 element equalizer is proposed which can equalize all dipole/monopole like antennas. Simulation and experimental results confirm our hypothesis. The second contribution of this thesis is in the design of broadband, small size, modular arrays (2, 4, 8 or 16 elements) using the distributed approach to impedance matching. The design of arrays comprising a small number of elements cannot follow the infinite array design paradigm. Instead, the central idea is to find a single optimized radiator (unit cell) which if used to build the 2x1, 4x1, 2x2 arrays, etc. (up to a 4x4 array) will provide at least the 2:1 bandwidth with a VSWR of 2:1 and stable directive gain (not greater than 3 dB variation) in each configuration. Simulation and experimental results for a solution to the 2x1, 4x1 and 2x2 array configurations is presented. "

<p>Efficient, but low-profile and small-footprint antennas for VHF-UHF range applications remains an ongoing work. VHF range spans approximately 54 - 88 MHz while UHF roughly ranges from 174 - 890 MHz. The inverse relationship between the physical length and resonant frequency of an antenna, which is a measure of its operating frequency range, is well known. A direct correlation between an antenna's physical length and radiation efficiency has also been established. Therefore, a combination of these constraints complicates the design of low-frequency antennas that have small physical size but with enough radiation resistance to be an efficient radiator when connected to a source having a comparable resistance. Given the frequency bands above, their corresponding wavelengths will be: 3.4-5.5 m (VHF) and 0.3-1.7 m (UHF). The length of an antenna operating at these wavelengths would need to be electrically-small i.e. a fraction of wavelength given size constraints for applications such as defense or commercial mobile communication equipment. As a consequence, the radiation resistance of the antenna, which is a function of its radiation efficiency, is greatly reduced. In other words, the input impedance or radiation impedance (assuming negligible ohmic losses in the antenna structure) features a small resistive component and a large capacitive component, causing reflections of most of the incident power to the antenna. Highly-reactive antennas are not desired for most transmitters and receivers. Therefore, the radiation resistance of an antenna must be increased by increasing its electrical length while simultaneously maintaining a low profile and footprint. This aim can be achieved by configuring the antenna to excite a resonance at, or very close to a desired operating frequency. An approach that I will explore in this dissertation is to exploit the broadband characteristics of meander-line and helical (or "spiral") antennas typically applied in the microwave frequency range to the UHF-VHF range. I will also propose novel antenna geometries that combine spiral and meander-line properties and analyze their performance. These antennas offer significant size reductions; for example, a bowtie meander dipole antenna studied yielded a height reduction of 55% at 64 MHz relative to a half-wave dipole antenna of the same resonant frequency. In addition, I will present a set of equations developed for predicting the fundamental resonant frequency and radiation resistance of meander-line antennas.</p> / Dissertation

With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.

With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.

Non-radiative wireless power transfer using the coupled mode resonance phenomenon has been widely reported in the literature. However, the distance over which such phenomenon exists is very short when measured in terms of wavelength. In this dissertation, how efficient wireless power transfer can be realized in the radiating near-field region beyond the coupled mode resonance region is investigated. First, electrically small folded cylindrical helix (FCH) dipole antennas are designed to achieve efficient near-field power transfer. Measurements show that a 40% power transfer efficiency (PTE) can be realized at the distance of 0.25λ between two antennas in the co-linear configuration. These values come very close to the theoretical upper bound derived based on the spherical mode theory. The results also highlight the importance of antenna radiation efficiency and impedance matching in achieving efficient wireless power transfer. Second, antenna diversity is explored to further extend the range or efficiency of the power transfer. For transmitter diversity, it is found that a stable PTE region can be created when multiple transmitters are employed at sufficiently close spacing. For receiver diversity, it is found that the overall PTE can be improved as the number of the receivers is increased. Third, small directive antennas are investigated as a means of enhancing near-field wireless power transfer. Small directive antennas based on the FCH design are also implemented to enhance the PTE. It is shown that the far-field realized gain is a good surrogate for designing small directive antennas for near-field power transfer. Fourth, to examine the effects of surrounding environments on near-field coupling, an upper bound for near-field wireless power transfer is derived when a transmitter and a received are separated by a spherical material shell. The derived PTE bounds are verified using full-wave electromagnetic simulation and show good agreement for both TM mode and TE mode radiators. Using the derived theory, lossy dielectric material effects on wireless power transfer are studied. Power transfer measurements through walls are also reported and compared with the theory. Lastly, electrically small circularly polarized antennas are investigated as a means of alleviating orientation dependence in near-field wireless power transfer. An electrically small turnstile dipole antenna is designed by utilizing top loading and multiple folding. The circularly polarization characteristic of the design is first tested in the far field, before the antennas are placed in the radiating near-field region for wireless power transfer. It is shown that such circularly polarized antennas can lessen orientation dependence in near-field coupling. / text

ITC/USA 2013 Conference Proceedings / The Forty-Ninth Annual International Telemetering Conference and Technical Exhibition / October 21-24, 2013 / Bally's Hotel & Convention Center, Las Vegas, NV / In this paper, a new technique utilizing a scatterer of high dielectric constant in between electrically small antennas to achieve good Direction of arrival (DOA) estimation performance is demonstrated. The phase information of the received signal at the antennas is utilized for direction estimation. The impact of the property of the scatterer on the directional sensitivity and the output signal to noise ratio (SNR) level are studied. Finally the DOA estimation accuracy is analyzed with the proposed technique under the consumption of white Gaussian noise environment.

ITC/USA 2012 Conference Proceedings / The Forty-Eighth Annual International Telemetering Conference and Technical Exhibition / October 22-25, 2012 / Town and Country Resort & Convention Center, San Diego, California / There are always some intrinsic tradeoffs among the performance characteristics: radiation efficiency, directivity, and bandwidth, of electrically small antennas (ESAs). A non-Foster enhanced, broad bandwidth, metamaterial-inspired, electrically small, Egyptian axe dipole (EAD) antenna has been successfully designed and measured to overcome two of these restrictions. By incorporating a non-Foster circuit internally in the near-field resonant parasitic (NFRP) element, the bandwidth of the resulting electrically small antenna was enhanced significantly. The measured results show that the 10 dB bandwidth (BW10dB) of the non-Foster circuit-augmented EAD antenna is more than 6 times the original BW10dB value of the corresponding passive EAD antenna.

With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.