The diploma thesis is partly dedicated to energetic efficiency of buildings and describes possibilities how to evaluate energetic efficiency of buildings in the Czech Republic. We also get to know with distribution of thermal insulators by material base and use in construction. There are also mentioned methods how to determine thermal insulations characteristics of heat insulations, so called heat conductivity coefficient. The last and the crucial chapter of theoretic part is dedicated to thermal-reflective insulations. There are mentioned some of the basic characteristics of insulations, material composition and heat transfer mechanism in their structure as well. Practical part describes measurement of thermal resistance of chosen samples of thermal-reflective insulations per measuring device on the principal of Hot Box method. In the next step was determined emissivity of aluminium foils which forms the surface of chosen samples of thermal-reflective insulations. In the end of thesis are defined possibilities of use thermal-reflective insulations in building structures especially in passive and low-energy buildings in climatic conditions of the Czech Republic.

This diploma thesis is about thermomechanics of passenger car tires. The research part dealing with existing tire models is followed by the practical part. The practical part is based on the designs of thermomechanical models. The first model determines a dependence of temperature on the air pressure inside a tire when a temperature changes. The second thermomechanical model captures all the heat fluxes which affect a tire while a vehicle is in motion. The third thermomechanical model calculates temperatures of parts of the tire during driving tests. All models are programmed in MATLAB.

The master‘s thesis deals with utilization of infrared camera for temperature measurement of electrical machines. The first part describes non-contact temperature measuring, the second part describes principle of sensors that evaluate quantity of incident infrared radiation. In the next part there is termovision camera SAT-HY 6800 presented and the instructional manual for SAT Report computer programme created. This computer programme is used for analyzing of termovision pictures from the SAT-HY 6800 termovison camera. The chapter 7 describes temperature measuring of one-phase asynchronous motor type J22TO484. The chapter 8 describes temperature measuring of semiconductor components of EC motor G6 series. Both of these motors are produced by ATAS elektromotory Náchod a.s. The last part of the thesis describes creation of animation of one-phase asynchronous motor type J22TO455. The animation was created in 3ds Max computer programme.

This work thoroughly analyzes a previously created computational model for predicting characteristic properties of the combustion process in an experimental combustion chamber. Any found shortcomings of the original model are removed and the model is further improved prior to its application on 11 real cases of combustion tests performed at various conditions and with various fuels. Data provided by the model are confronted with the data obtained during the combustion tests and the model accuracy is evaluated, based on local heat flux along the length of the combustion chamber. Finally, the overall usefulness of the model is determined by the means of evaluating the acquired accuracy values, and further possibilities of model improvement and use are presented.

The master´s thesis analyzes influence of direct and reflected solar radiation to heat strain and degradation of thermal insulation in the flat roof construction. In many building was a problem in a significant degradation of thermal insulation made from expanded polystyrene in the vicinity of glass surfaces. To determine the causes of this problem, it was necessary to study and test the properties of building materials and the physical nature of the effect of solar radiation on the building structure. In the introductory section lists the cases of buildings with degradation of thermal insulation and existing knowledge on this issue. The theoretical part describes the technical properties of thermal insulating materials used in the flat roof construction, nature and division of solar radiation, optical laws of light reflection and physical theory to explain the technical thermal behavior of building materials and structures. The last part describes a practical model and analyzing measured data in thermal stress in the flat roof construction. The practical part also determines the importance of different influences configuration structures using to dynamic simulations. At the end of the practical part they are validated theoretical knowledge obtained by analyzing data from a practical model.

Presented work deals with the study progressive heat-reflecting foil thermal insulating materials and defines their thermal insulation properties. The work describes a transport mechanism of thermal energy in the structure of heat-reflecting materials, their physical properties, especially heat resistance, compared to the conventional thermal insulating materials available on Czech market. The main applications ways and installation methods of these materials (especially in low-energy and passive buildings) are also shown. The practical part is focused on asembling the measuring device HOT BOX in accordance with the valid standards, to determine the heat resistance of heat-reflecting materials. In next step the measurement of reflection of aluminum foils (an integral part of the structural arrangement heat-reflecting foil insulations) was performed.

The master´s thesis deals with verification of thermal insulating property of thermoreflection foil insulations. The teoretical part of thesis focuses on the energy demand of buildings, the problems of heat transfer material, terms required for study of thermoreflection thermal insulation and experimental methods for determination of thermal insulating properties of insulators. In the next part the chapter is accompanied by an overview of the most common insulation materials which used in construction. The last part of teoretical part is devoted to the description of thermoreflect formation and analysis of the spread of thermal insulating layers of thermoreflection thermal insulation. The first part of thesis is devoted to the use of thermoreflection therm insulation in buildings. The second part of thesis is devoted to the design, assembly and calibration of the measuring device that uses a method of protected warm chamber. It is declared as a binding method of detection of the heat transfer performance of thermoreflection thermal insulation. The developed measuring device allows detection of endpoints in some direction of propagation of heat. Measurment of heat transfer coefficient devoted the third part of practical part. This part contains a description of the samples used for the measurement of the heat transfer coefficient. In the fourth chapter of the practical part are presented the results of the heat transfer coefficient measurments on selected samples of thermoreflection foil insulation. It is shown the characteristic of heat transfer coefficient of individual samples, the dependence of the heat transfer coefficient on the position of the sample in the measuring device and the recommendation of an appropriate use of sample in the works for the climatic conditions of the Czech republic. The work concludes the chapter of comparing and evaluating of all samples with practical recommendations.