Fibre reinforcement polymers (FRP) are non-corrodible materials used instead of conventional steel and have been approved to be an effective way to overcome corrosion problems. FRP, in most cases, can have a higher tensile strength, but a lower tensile modulus of elasticity compared to that of conventional steel bars. This study aimed to examine flat slab specimens reinforced with glass fibre reinforced polymer (GFRP) and steel bar materials for punching shear behaviour. Six full-scale two-way slab specimens were constructed and tested under concentric load up to failure. One of the main objectives is to study the effect of reinforcement spacing with the same reinforcement ratio on the punching shear strength. In addition, two other parameters were considered, namely, slab depth, and compressive strength of concrete. The punching shear provisions of two code of practises CSA S806 (Canadian Standards 2012) and JSCE (JSCE et al. 1997) reasonably predicted the load capacity of GFRP reinforced concrete flat slab, whereas, ACI 440 (ACI Committee 440 2015) showed very conservative load capacity prediction. On the other hand, a dynamic explicit solver in nonlinear finite element (FE) modelling is used to analyse a connection of column to concrete flat slabs reinforced with GFRP bars in terms of ultimate punching load. All FE modelling was performed in 3D with the appropriate adoption of element size and mesh. The numerical and experimental results were compared in order to evaluate the developed FE, aiming to predict the behaviour of punching shear in the concrete flat slab. In addition, a parametric study was created to explore the behaviour of GFRP reinforced concrete flat slab with three parameters, namely, concrete strength, shear load perimeter to effective depth ratio, and, flexural reinforcement ratio. It was concluded that the developed models could accurately capture the behaviour of GFRP reinforced concrete flat slabs subjected to a concentrated load. Artificial Neural Networks (ANN) is used in this research to predict punching shear strength, and the results were shown to match more closely with the experimental results. A parametric study was performed to investigate the effects of five parameters on punching shear capacity of GFRP reinforced concrete flat slab. The parametric investigation revealed that the effective depth has the most substantial impact on the load carrying capacity of the punching shear followed by reinforcement ratio, column perimeter, the compressive strength of the concrete, and, the elastic modulus of the reinforcement.

yes / This paper reports the testing of five reinforced concrete continuous beams strengthened in flexure with externally bonded carbon-fibre-reinforced polymer (CFRP) laminates. All beams had the same geometrical dimensions and internal steel reinforcement. The main parameters studied were the position and form of the CFRP laminates. Three of the beams were strengthened using different arrangements of CFRP plate reinforcement, and one was strengthened using CFRP sheets. The performance of the CFRP-strengthened beams was compared with that of an unstrengthened control beam. Peeling failure was the dominant mode of failure for all the strengthened beams tested. The beam strengthened with both top and bottom CFRP plates produced the highest load capacity. It was found that the longitudinal elastic shear stresses at the adhesive/concrete interface calculated at beam failure were close to the limiting value recommended in Concrete Society Technical Report 55.

Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: This study set out to determine the debonding of externally applied Carbon Fibre Reinforced Polymer (CFRP) plates from RC structures under cyclic loading. Triplet shear tests and finite element (FE) analyses were done on the epoxy to determine the bond stress between the CFRP plate and a reinforced concrete specimen. From these tests and analyses the average shear strength of the bond between the epoxy and concrete substrate was determined and the shear strength of the epoxy specified by the supplier could be confirmed. A case study of a statically loaded beam was performed to verify the bond strength. Finally a reinforced concrete (RC) T-section was designed and pre-cracked to simulate a damaged beam in practice. These sections were then externally reinforced by bonding CFRP plates onto the face of the web. The sections were subjected to static and cyclic loading at different force amplitudes. Along with the experimental tests, FE models were developed and analysed which had the same geometrical and material properties as the experimental specimens. Due to time constraint a FE mesh objectivity study was not done, but the chosen element size is believed to be sufficiently small to replicate the experimental tests objectively. The FE analyses and the experimental tests yielded results that were close to each other on both the global scale and in terms of localised behaviour, thus it was decided that the computational approach could be used for the final design of a model of the debonding of CFRP plates bonded onto RC beams under cyclic loading because the data can be analysed more easily and a large variation of tests can be done. For the T-section 3 tests were conducted; a pull-off (static) test where the bonded CFRP plate was pulled from a specimen to get the ultimate failure envelope of the test specimens. The static test was followed by cyclic tests with force amplitude of 85% and 65% of the ultimate pull-off strength. Different measurements were taken to get the global and local displacement behaviour of the section. The global displacement was measured by means of a linear variable displacement transducer (LVDT, displacement meter) clamped onto the CFRP plate that pushed on the top of the concrete and the local displacement was measured with the help of the Aramis system. The displacement was then compared to the same displacements of nodes and elements in the FE models. The result was a confirmation that the results from the FE models were sufficient to design a model for cyclic debonding of CFRP plates from RC structures. From the FE models the relative displacement between the CFRP plate and concrete was obtained in the vicinity of a crack. This relative displacement was then normalised by the respective stress range of the different tests, from which the normalised relative displacement was plotted against the number of cycles to get an equation limiting the number of cycles for a specific stress range. From the results, it appears that for cyclic load levels up to 65% of the peak static resistance, a threshold number of load cycles are required for delamination initiation. Subsequently, a near constant delamination rate is reached. The delamination rate is significantly lower for lower cyclic load levels. Finally, an unstable delamination stage is reached at a level of about 65 μm for all the analyses, after which CFRP pull-off is imminent. Service life design of CFRP reinforcement of RC beams should take into consideration the delamination initiation threshold, the subsequent delamination rate and finally the initiation of unstable delamination. / AFRIKAANSE OPSOMMING: Die projek is uitgevoer om die delaminasie van ekstern aangewende Koolstof Vesel Versterkte Polimeer (KVVP) stroke op gewapende beton strukture te bepaal onder sikliese belasting. Triplet skuif toetse is gedoen op die gebruikte epoksie om die verband-sterkte te bepaaltussen die KVVP stroke en die beton proefstuk. Die skuif toetse is ook met behulp van die eindige element (EE) metode geanaliseer. Die resultaat van die toetse en analises het gewys dat die verband sterkte tussen die KVVP stroke en beton gelyk is aan die skuif sterkte van die epoksie wat verskaf is. `n Gevalle studie van `n monotonies belaste balk is gedoen om die verband-sterkte te verifieër. `n Gewapende beton T-snit is ontwerp en voor-af gekraak om `n beskadigde balk in die praktyk voor te stel. Die beskadigde proefstukke is vervolgens ekstern versterk met KVVP stroke wat aan die web van die T-snit vas geplak is. Die versterkte T-snitte is getoets onder statiese en sikliese belasting. Die sikliese toetse is ook onder verskillende spanningsamplitudes getoets. Om die eksperimentele toetse te verifieër is EE modelle gebou en geanaliseer wat dieselfde geometriese en materiaal eienskappe as die eksperimentele proefstukke gehad het, maar as gevolg van `n tydsbeperking is `n sensitiwiteit studie oor die element grootte nie gedoen nie. Die element grootte is klein genoeg gekies en word beskou as voldoende om die gedrag objektief te simuleer. Die EE analises en eksperimentele resultate was na genoeg aan mekaar op beide globale en lokale vlak. Dus is `n analitiese benadering tot die toetse vervolgens gebruik vir die ontwerp van `n model vir delaminasie van KVVP stroke van gewapende beton strukture onder sikliese belasting. Die EE metode stel die analis in staat om `n verskeidenheid van toetse relatief vinnig uit te voer en om die data van die toetse vinniger te interpreteer as deur fisiese eksperimentele toetse. Drie eksperimente is uitgevoer op die T-snitte, `n aftrek-toets (staties) waar die KVVP strook van `n proefstuk afgetrek is om die falingsomhullende diagram te kry en dan ook twee sikliese toetse teen 85% en 65% van die krag amplitude van die falingskrag. Verplasingsmeters is gebruik om die globale verplasing te kry, deur dit vas te klamp op die KVVP strook en dan die verplasing te meet relatief tot die bokant van die beton. Die lokale veplasing is met behulp van die Aramis sisteem verkry. Die eksperimentele verplasings is dan vergelyk met verplasings van die ooreenstemmende nodes en elemente in die EE modelle. Deur die vergelyking van die resultate is dit bevestig dat die eindige element modelle voldoende is om die model vir sikliese delaminasie van KVVP stroke van gewapende beton strukture te gebruik vir die ontwerp. Uit die EE modelle is die relatiewe verplasing tussen die KVVP strook en die beton gekry in die omgewing van `n kraak. Die relatiewe verplasing is genormaliseer deur elkeen se spanningsamplitude. Die genormaliseerde relatiewe verplasing is dan teenoor die aantal siklusse geteken waarvan `n vergelyking vir die maksimum verplasing afgelei is om die aantal siklusse vir `n gegewe spanning amplitude te beperk. Uit die resultate blyk dit dat vir sikliese laste tot en met 65% van die piek statiese weerstand `n aantal siklusse moontlik is voordat delaminasie begin waarna `n konstante delaminasie tempo bereik word. Die delaminasie tempo is stadiger vir sikliese laste teen `n laer belastings amplitude. Laastens word `n onstabiele delaminasie fase bereik by `n vlak van ongeveer 65 μm, na die oorgang delamineer die KVVP strook binne enkele siklusse. Die beginpunt van delaminasie, die delaminasie tempo en laastens die begin van onstabiele delaminasie moet in gedagte gehou word by die ontwerp diens leeftyd van KVVP versterkte gewapende beton balke.

Die Arbeit beschreibt die skalenübergreifende Modellierung und Simulation des Werkstoffverhaltens von Faser-Kunststoff-Verbunden mit textiler Verstärkungsstruktur, die ausgehend von den konstitutiven Eigenschaften der Verbundbestandteile (Mikroskala) und ihrer geometrischen Anordnung im Verbund (Mesoskala) die rechnerische Vorhersage des effektiven Materialverhaltens des Verbundes (Makroskala) ermöglicht. Neben Schädigungsprozessen beeinflusst insbesondere das dehnratenabhängige Materialverhalten der polymeren Matrix das mechanische Verhalten des Verbundes. Dieser Einfluss wird anhand verschiedener Glasfaser-Polypropylen-Verbunde numerisch untersucht. Ein viskoplastisches Materialmodell bildet dabei das nichtlineare Materialverhalten von Polypropylen ab. Die Modellierung der textilen Verstärkungsstruktur erfolgt durch Anwendung der erweiterten Finiten-Elemente-Methode (XFEM). Anhand des Vergleichs von rechnerisch und experimentell gewonnenen Ergebnissen erfolgt schließlich die Verifikation der vorgeschlagenen Modellierungsstrategie. / This contribution covers the trans-scale modelling and simulation of the mechanical behaviour of textile-reinforced polymers. Starting from the material properties of the individual constituents (micro-scale) and their geometrical arrangement (meso-scale), the effective material behaviour of the composite (macro-scale) is numerically predicted. In addition to damage processes, the inelastic deformation behaviour of the composite is influenced by the strain-rate dependent material behaviour of the polymeric matrix. This influence is numerically investigated for different glass-fibre-polypropylene composites. A viscoplastic material model accounts for the nonlinear mechanical behaviour of polypropylene. The complex textile reinforcement is modelled by the eXtended finite element method (XFEM). A comparison of computed and experimental results allows for the verification of the proposed modelling strategy.

End-gated and centre gated mouldings have been assessed with varying thickness and sprue geometries for the centre gate. Alternative image analysis techniques are used to measure the orientation and length of injection moulded short and long fibres composite components. The fibre orientation distribution (FOD) measurements for both geometries have been taken along the flow path. In shear flow the FOD changes along the flow path, however the FOD remains relatively constant during expansion flow. The core width and FOD at the skin within a long glass fibre (LGF) specimen is different in comparison to a short glass fibre (SGF) specimen. Fibre length measurements have been taken from the extrudate, sprue and 2 positions within the centre gate cavity. The size of the sprue has little influence on fibre breakage if the moulding is more than 1 mm thick The SGF FOD prediction models within Autodesk Simulation Moldflow Insight 2014 (ASMI) have been validated against measured SGF data. At present, by default, the models over-predict the < cos2θ > for most geometries. When the coefficients are tailored for each model, drastic improvements are seen in the FOD prediction. The recently developed SGF RSC model accurately predicts the FOD in shear, in a thin geometry, whereas the Folgar-Tucker model predicts the FOD accurately in expansion flow. The measured LGF fibre length distribution (FLD) and FOD have been validated against the LGF prediction models. The LGF models are currently under predicting the breakage and over-predicting < cos2θ >. The breakage prediction improves if measured FLD of the extrudate is input into the model.

This work aims to investigate the flexural behaviour of continuous hybrid reinforced concrete T-beams (HRCT). The investigations consist of three parts; the computational part, the experimental part and the finite element analysis. The computational part included two parts, the first one is developing an analytical programme using MATLAB software to investigate the moment-curvature behaviour of HRCT-beams and to design the experimental specimens. This was followed by the experimental part, where six full-scale reinforced concrete continuous T beams were prepared and tested. One beam was reinforced with glass fibre reinforced polymer (GFRP) bars while the other five beams were reinforced with a different combination of GFRP and steel bars. The ratio of GFRP to steel reinforcement at both mid-span and middle-support sections was the main parameter investigated. The results showed that adding steel reinforcement to GFRP reinforced concrete T-beams improves the axial stiffness, ductility and serviceability in terms of crack width and deflection control. However, the moment redistribution at failure was limited because of the early yielding of steel reinforcement at the beam section that did not reach its moment capacity and could still carry more loads due to the presence of FRP reinforcement. The second part of the computational part included the comparison between the experimental results with the ultimate moment prediction of ACI 440.2R-17, and with the existing theoretical equations for moment capacity, load capacity, and deflection prediction. It was found that the ACI 440.2R-17 design code equations reasonably estimated the moment capacity of both mid-span and middle-support sections and consequently predicted the load capacity of the HRCT-beams based on fully ductile behaviour. However, Qu's and Safan's equations underestimated the predicted moment and load-capacity of HRCT-beams. Also, Bischoff's and Yoon's models underestimated the deflection at all stages of the load for both GFRP and HRCT- beams. For the numerical part, a three-dimensional finite element model has been developed using ABAQUS software to examine the behaviour of HRCT-beams. The experimental results were used to validate the accuracy of the FEM, where an acceptable agreement between the simulated and experimental results was observed. Accordingly, the model was used to predict the structural behaviour of continuous HRCT-beams by testing different parameters.

yes / This paper investigates the feasibility of using artificial neural networks (NNs) to predict the shear capacity of concrete members reinforced longitudinally with fibre reinforced polymer (FRP) bars, and without any shear reinforcement. An experimental database of 138 test specimens failed in shear is created and used to train and test NNs as well as to assess the accuracy of three existing shear design methods. The created NN predicted to a high level of accuracy the shear capacity of FRP reinforced concrete members. Garson index was employed to identify the relative importance of the influencing parameters on the shear capacity based on the trained NNs weightings. A parametric analysis was also conducted using the trained NN to establish the trend of the main influencing variables on the shear capacity. Many of the assumptions made by the shear design methods are predicted by the NN developed; however, few are inconsistent with the NN predictions.

End-gated and centre gated mouldings have been assessed with varying thickness and sprue geometries for the centre gate. Alternative image analysis techniques are used to measure the orientation and length of injection moulded short and long fibres composite components. The fibre orientation distribution (FOD) measurements for both geometries have been taken along the flow path. In shear flow the FOD changes along the flow path, however the FOD remains relatively constant during expansion flow. The core width and FOD at the skin within a long glass fibre (LGF) specimen is different in comparison to a short glass fibre (SGF) specimen. Fibre length measurements have been taken from the extrudate, sprue and 2 positions within the centre gate cavity. The size of the sprue has little influence on fibre breakage if the moulding is more than 1 mm thick The SGF FOD prediction models within Autodesk Simulation Moldflow Insight 2014 (ASMI) have been validated against measured SGF data. At present, by default, the models over-predict the <cos2θ> for most geometries. When the coefficients are tailored for each model, drastic improvements are seen in the FOD prediction. The recently developed SGF RSC model accurately predicts the FOD in shear, in a thin geometry, whereas the Folgar-Tucker model predicts the FOD accurately in expansion flow. The measured LGF fibre length distribution (FLD) and FOD have been validated against the LGF prediction models. The LGF models are currently under predicting the breakage and over-predicting <cos2θ>. The breakage prediction improves if measured FLD of the extrudate is input into the model. / Autodesk Ltd.

A novel type of precast, prestressed concrete structural element is being implemented in load-bearing systems in buildings. These structural elements combine the use of high-performance, self-consolidating concrete (HPSCC) and non-corroding carbon fibre reinforced polymer (CFRP) prestressing tendons; this produces highly optimized, slender structural elements with excellent serviceability and (presumed) extended service lives. More widely, the use of new construction techniques, innovative materials, and ground-breaking designs is increasingly commonplace in today's rapidly evolving building construction industry. However, the performance of these and other structural elements in fire is in general not well known and must be understood before these can be used with confidence in load-bearing applications where structural fire resistance is a concern. Structural fire testing has traditionally relied on the use of the standard fire resistance test (i.e. furnace test) for assuring regulatory compliance of structural elements and assemblies, and in many cases also for developing the scientific understanding of structural response to fire. Conceived in the early 1900s and fundamentally unchanged since then, the standard testing procedure is characterized by its high cost and low repeatability. A novel test method, the Heat-Transfer Rate Inducing System (H-TRIS), resulting from a mental shift associated with controlling the thermal exposure not by temperature (e.g. temperature measured by thermocouples) but rather by the time-history of incident heat flux, was conceived, developed, and validated within the scope of the work presented in this thesis. H-TRIS allows for experimental studies to be carried out with high repeatability, imposing rationally quantifiable thermal exposure, all at low economic and temporal cost. The research presented in this thesis fundamentally seeks to examine and understand the behaviour of CFRP prestressed HPSCC structural elements in fire, with emphasis placed on undesired 'premature' failure mechanisms linked to the occurrence of heat-induced concrete spalling and/or loss of bond between the pretensioned CFRP tendons and the concrete. Results from fire resistance tests presented herein show that, although compliant with testing standards, temperature distributions inside furnaces (5 to 10% deviation) appear to influence the occurrence of heat-induced concrete spalling for specimens tested simultaneously during a single test; fair comparison of test results is therefore questionable if thermal exposure variability is not explicitly considered. In line with the aims of the research presented in this thesis, H-TRIS is used to carry out multiple comprehensive studies on the occurrence of concrete spalling and bond behaviour of CFRP tendons; imposing a quantified, reproducible and rational thermal exposure. Test results led to the conclusion that a "one size fits all" approach for mitigating the risk of heat-induced concrete spalling (e.g. prescribed dose of polypropylene (PP) fibres included in fresh concrete), appears to be ineffective and inappropriate in some of the conditions examined. This work demonstrates that PP fibre cross section and individual fibre length can have an influence on the risk of spalling for the HPSCC mixes tested herein. The testing presented herein has convincingly shown, for the first time using multiple repeated tests under tightly controlled thermal and mechanical conditions, that spalling depends not only on the thermal gradients in concrete during heating but also on the size and restraint conditions of the tested specimen. Furthermore, observations from large scale standard fire resistance tests showed that loss of bond strength of pretensioned CFRP tendons occurred at a 'critical' temperature of the tendons in the heated region, irrespective of the temperature of the tendons at the prestress transfer length, in unheated overhangs. This contradicts conventional wisdom for the structural fire safety design of concrete elements pretensioned with CFRP, in which a minimum unheated overhang is generally prescribed. Overall, the research studies presented in this thesis showed that a rational and practical understanding of the behaviour of CFRP prestressed HPSCC structural elements during real fires is unlikely to be achieved only by performing additional standard fire resistance tests. Hence, H-TRIS presents an opportunity to help promote an industry-wide move away from the contemporary pass/fail and costly furnace testing environment. Recommendations for further research to achieve the above goal are provided.

Concrete deep beams with small shear span-to-depth (a/d) ratios are common elements in structures. However, there are few experimental results on the behaviour of FRP reinforced concrete deep beams and no specific modelling techniques exist in design codes for such members. The objectives of this study were to examine the shear behaviour of FRP reinforced concrete deep beams containing no web reinforcement and to develop a modelling technique. Test results of 12 large-scale specimens are reported where the primary variables included the a/d ratio, reinforcement ratio, member height, and concrete strength. The results showed that an arch mechanism was able to form in FRP reinforced concrete beams having a/d 2.1. A strut and tie modelling procedure adapted from CSA A23.3-04 was capable of accurately predicting the capacity of FRP reinforced concrete deep beams containing no web reinforcement while sectional shear models gave poor, but conservative, predictions. / Structural Engineering