The high cost of repairing reinforced or prestressed concrete structures due to steel corrosion has driven engineers to look for solutions. Much research has been conducted over the last two decades to evaluate the use of Fiber Reinforced Polymers (FRPs) in concrete structures. Structural engineering researchers have been testing FRP to determine their usability instead of steel for strengthening existing reinforced concrete structures, reinforcing new concrete members, and for prestressed concrete applications. The high strength-to-weight ratio of FRP materials, especially Carbon FRP (CFRP), and their non-corrosive nature are probably the most attractive features of FRPs. In this study, an experimental program was conducted to investigate the flexural behavior of prestressed concrete beams pre-tensioned with CFRP strands. The bond characteristics were examined by means of experimentally measuring transfer length, flexural bond length, and bond stress profiles. A total of four rectangular beams pre-tensioned with one 0.5-in. diameter CFRP strand were fabricated and tested under cyclic loading for five cycles, followed by a monotonically increasing load until failure. In investigating bond properties, the experimental results were compared to the equations available in the literature. The results from the four flexural tests showed that the main problem of CFRP strands, in addition to their liner-elastic tensile behavior, was lack of adequate bonding between FRP and concrete. Poor bonding resulted in early failure due to slippage between FRPs and concrete. As a result, a new technique was developed in order to solve the bonding issues and improve the flexural response of CFRP prestressed concrete beams. The new technique involved anchoring the CFRP strands at the ends of the concrete beams using a new "steel tube" anchorage system. It was concluded that the new technique solved the bond problem and improved the flexural capacity by about 46%. A computer model was created to predict the behavior of prestressed beams pre-tensioned with CFRP. The predicted behavior was compared to the experimental results. Finally, the experimental results were compared to the behavior of prestressed concrete beams pre-tensioned with steel strands as generated by the computer model. The CFRP beams showed higher strength but lower ductility.

A variety of retrofitting methods are used to upgrade existing structures. For example, steel plates and Fiber Reinforced Polymer (FRP) jackets are externally bonded to members to increase their capacity in flexure and shear. However, due to the issue of corrosion these strengthening systems may lose their efficiency with time. FRP materials have been used to strengthen many structural components of different shapes and types. FRP jackets, FRP Strips, and FRP rods have commonly been used to rehabilitate existing structural components. The many advantages of using FRP as strengthening materials have made this material an attractive alternative: advantages such as lightweight, high strength, and ease of setting up. Among the many applications using FRP, Near Surface Mounted -- Fiber Reinforced polymer (NSM-FRP) is a promising technique used to strengthen concrete members. However, de-bonding issues have to be overcome to make this technique efficient and reliable. The NSM-FRP technique consists of making a groove along the surface of the concrete member to be retrofitted with depth less than the cover of the member. After cleaning the groove, epoxy paste is used to fill two-thirds of the groove's depth. The FRP element is then mounted in the groove. Finally, the groove is filled with epoxy and the excessive epoxy is leveled with surface of the concrete. This technique makes the FRP material completely covered by epoxy in the cover of the concrete. This method can be used for strengthening both the positive and negative moment regions of girders and slabs. Groove size, paste, concrete, and rods properties are the main variables that control the efficiency of the NSM-FRP rods. The main objective of this research project is to determine the behavior of reinforced concrete beams that are strengthened with NSM-CFRP reinforcement bars. In this research project, the bond characteristics of NSM-CFRP reinforcement bars are first determined from pullout tests. Then, NSM-CFRP rods are installed in reinforced concrete beams and the beams are tested. Loads, strains, and deflections are measured and theoretical and measured capacities are compared. Finally, the reliability and efficiency of using NSM-CFRP rods technique in retrofitting existing structures is observed.

This master’s thesis describes an experimental program investigating the strengthening of beams of glued laminated timber with composite reinforcement. The work compares the behavior of beams reinforced with composite reinforcement with unreinforced beam and with solid timber beam. The work also deals with identifying and evaluating the physic-mechanical properties of materials.

ABSTRACT The repair and strengthening of concrete bridge members with CFRP has become increasingly popular over recent years. However, significant research is still needed in order to develop more robust guidelines and specifications. The research project aims to assist with improving design prosedures for damaged concrete members with the use of CFRP. This document summarizes the analysis and testing of full-scale 40’ foot long prestressed concrete (PSC) bridge girders exposed to simulated impact damage and repaired with carbon fiber reinforced polymers (CFRP) materials. A total of five AASHTO type II bridge girders fabricated in the 1960’s were taken from an existing bridge, and tested at the Florida Department of Transportation FDOT structures lab in Tallahassee, Florida. The test specimens were tested under static loading to failure under 4-point bending. Different CFRP configurations were applied to each of the girders. Each of the test girders performed very well as each of them held a higher capacity than the control girder. The repaired girders 5, 6 and 7 surpassed the control girder’s capacity by 10.88%, 15.9% and 11.39%. These results indicate that repairing laterally damaged prestressed concrete bridge girders with CFRP is an effective way to restore the girders flexural capacity.

This thesis was most concerned with the mechanical response to irradiation of two in-house produced oxide dispersion strengthened (ODS) steels and two non-ODS coun- terparts. The steels, manufactured by Dr. M. J. Gorley (University of Oxford), were me- chanically alloyed from gas-atomised Fe-14Cr-3W-0.2Ti, with the addition of 0.25Y₂O₃ powder in the case of the ODS variants. The powders were hot isostatic pressed at consolidation temperatures of 950 °C and 1150 °C. The four steels were designated 14WT 950 (non-ODS), 14YWT 950 (ODS), 14WT 1150 (non-ODS) and 14YWT 1150 (ODS), and were used in the as-produced condition. Initially, the macroscale elastic modulus and yield stress were determined using a four-point flexure test, employing digital image correlation (DIC) as a strain gauge. The microcantilever size eects were then characterised, and it was determined that the yield stress signicantly diverged from macroscale values at microcantilever beam depths of < 4.5 μm. Using knowledge of this, the in-house produced alloys were irradiated with 2 MeV protons at the Surrey Ion Beam Centre (University of Surrey, UK) to a displacement damage of ∼ 0.02 dpa and 0.2 dpa (Bragg peak). This was to produce a deep irradiated layer for the fabrication of large microcantilevers with reduced size effects. The cross-sectional surface of the irradiated layer was then exposed and inclined linear arrays of 250 nm deep indents were placed across the damage prole. 14WT 1150 (non-ODS) revealed a clear proton damage prole in plots of hardness against irradiation depth, 14WT 950 (non-ODS) also showed modest hardening in the region of the Bragg peak. No appreciable hardening was observed in either 14YWT specimens, attributed to the fine dispersion of nanoscale oxides providing a high number density of defect sink sites. However, a large bimodal variation in hardness was measured in both ODS variants. This was investigated using EBSD and EDX, and was determined to be caused by a pronounced heterogeneity of the microstructure. While Hall-Petch strengthening and changes in the local chemistry had some effect on the measured hardness, the most likely cause of the large variation in local hardness was heterogeneity in the nanoscale oxide population. Microcantilevers were fabricated out of the irradiated layer cross-section in 14WT 1150 and 14YWT 1150. Larger microcantilevers, with ∼ 5 μm beam depth, were placed with their beam centre at ∼ 0.026 dpa. Smaller microcantilevers, with ∼ 1.5 μm beam depth, were placed with their beam centre at the Bragg peak, 0.2 dpa. Both the large and the small microcantilevers fabricated in 14WT 1150 (non-ODS) displayed significant irradiation hardening. In the ODS variant, 14YWT 1150, irradiation hardening appeared to be reduced. The work in this thesis successfully showed that it was possible to extract a close approximation of the macroscale yield stress from shallow irradiated layers, providing that the irradiation condition is carefully chosen in response to known size dependent behaviour. This thesis also investigated the size dependent behaviour of microcantilevers using a lengthscale dependent crystal plasticity UMAT, developed by Dunne et al. and implemented within ABAQUS 6.14-2 commercially available nite element software. The simulation of the GND density evolution with increasing plastic strain allowed their contribution to the microcantilever size effect, through mobile dislocation pinning, to be determined. This novel approach to modelling size effects in three dimensional finite element microcantilever models demonstrated that while it was possible to simulate a lengthscale-dependent response in finite element microcantilever models, the constitutive equation for the plastic velocity gradient needs to be more physically based in order the match the experimentally derived results; for example, a lengthscale-dependent term relating to the dislocation source density of the material. Although the apparent reduction of irradiation hardening in ODS in-house produced alloys showed great promise, these alloys also displayed a large amount of scatter in measured hardness and yield stress, attributed to the pronounced heterogeneity in the microstructure. Alloys with such signicant microstructural heterogeneity are not suitable for engineering or commercial use.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / A evolução dos concretos utilizados nas últimas décadas deu origem ao Concreto de Alto Desempenho (CAD), que tem, entre suas características, alta resistência à compressão e baixa permeabilidade. Com o desenvolvimento dos produtos químicos utilizados na construção civil, em especial os superplastificantes e superfluidificantes, a utilização desse tipo de concreto tornou-se cada vez mais freqüente pela possibilidade de se obter uma mistura suficientemente trabalhável utilizando-se fatores água/cimento menores do que 0,35. Devido à sua microestrutura mais homogênea, esse tipo de concreto apresenta um comportamento mais frágil do que os concretos convencionais, exigindo uma melhor caracterização do material. A partir do final da década de 70 começou-se a aplicar os conceitos da Mecânica da Fratura para análise do comportamento de estruturas construídas com esse tipo de concreto. Como em algumas situações a resistência nominal de peças de concreto diminui com o aumento de suas dimensões, houve a necessidade de se considerar o efeito de escala das estruturas a fim de se obter níveis de segurança mais adequados no seu dimensionamento, o que justificou a utilização da Mecânica da Fratura. Neste trabalho a energia de fraturamento foi obtida experimentalmente pelo método do trabalho de fraturamento e pelo método do efeito de escala, por meio de ensaios estáveis de flexão de três pontos em amostras de concreto de alto desempenho com entalhe. Foi também desenvolvida a simulação numérica de uma viga com entalhe, analisada pelo método dos elementos finitos e empregando-se na modelagem constitutiva os conceitos da Mecânica da Fratura aplicada ao concreto. As vigas foram moldadas e ensaiadas no Instituto Politécnico do Rio de Janeiro (IPRJ) da Universidade do Estado do Rio de Janeiro (UERJ) na cidade de Nova Friburgo. Os ensaios foram realizados com controle de deslocamento da célula de carga. Foram ensaiadas três séries de 12 vigas, com quatro dimensões diferentes, geometricamente proporcionais, e três amostras para cada dimensão, totalizando 36 vigas. As alturas utilizadas para as vigas foram 38, 76, 152 e 304 mm, e sua espessura foi mantida constante igual a 38 mm. Os corpos de prova cilíndricos, para caracterização da resistência à compressão do concreto, foram moldados no IPRJ e rompidos no laboratório de engenharia civil da UERJ, na cidade do Rio de Janeiro. Os concretos utilizados apresentaram resistência à compressão média de 70 MPa. / The evolution of the concrete mixes used during the last decades gave birth to the High Performance Concrete (HPC), which, among its main characteristics, presents high strength and low permeability. With the development of chemical products used in civil engineering constructions, mainly the superplasticizers, the use of this kind of concrete has become more and more frequent due to the possibility of obtaining a workable mixture with a water/cement ratio lower than 0.35. Due to its more homogeneous microstructure, the HPC presents a more fragile behavior than the conventional concrete, demanding a better characterization of the material. At the end of the 1970s, concepts of the Fracture Mechanics started to be used for the analysis of the structural behavior of concrete structures. As the nominal stress of the material decreases as the size of the structure increases, it became necessary to consider this size effect in the analysis in order to obtain more suitable levels of security. This fact justifies the use of the Fracture Mechanics in the structural analysis of concrete structures. In this work, the fracture energy was experimentally obtained using the work-offracture method and the size effect method by performing three-point bend tests in HPC notched beams. It was also developed a numerical simulation of the tests, performing the analysis through the Finite Element Method and applying the concepts of the Fracture Mechanics of Concrete into the constitutive model. The notched beams were molded and tested at the Polytechnic Institute of the State University of Rio de Janeiro (IPRJ/UERJ), located in the city of Nova Friburgo. The tests were controlled by the vertical displacement of the load cell. Three series of twelve beams with four geometrically similar sizes were tested. Three samples for each size were cast, making an amount of 36 beams. The beams were 38, 76, 152 and 304 millimeters high and the width was kept constant equal to 38 millimeters. To characterize the concrete compression strength, 100x200 millimeters cylinders were molded at the IPRJ and tested at the UERJ civil engineering laboratory in the city of Rio de Janeiro. The tested concretes presented a medium compressive strength of 70 MPa.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / A evolução dos concretos utilizados nas últimas décadas deu origem ao Concreto de Alto Desempenho (CAD), que tem, entre suas características, alta resistência à compressão e baixa permeabilidade. Com o desenvolvimento dos produtos químicos utilizados na construção civil, em especial os superplastificantes e superfluidificantes, a utilização desse tipo de concreto tornou-se cada vez mais freqüente pela possibilidade de se obter uma mistura suficientemente trabalhável utilizando-se fatores água/cimento menores do que 0,35. Devido à sua microestrutura mais homogênea, esse tipo de concreto apresenta um comportamento mais frágil do que os concretos convencionais, exigindo uma melhor caracterização do material. A partir do final da década de 70 começou-se a aplicar os conceitos da Mecânica da Fratura para análise do comportamento de estruturas construídas com esse tipo de concreto. Como em algumas situações a resistência nominal de peças de concreto diminui com o aumento de suas dimensões, houve a necessidade de se considerar o efeito de escala das estruturas a fim de se obter níveis de segurança mais adequados no seu dimensionamento, o que justificou a utilização da Mecânica da Fratura. Neste trabalho a energia de fraturamento foi obtida experimentalmente pelo método do trabalho de fraturamento e pelo método do efeito de escala, por meio de ensaios estáveis de flexão de três pontos em amostras de concreto de alto desempenho com entalhe. Foi também desenvolvida a simulação numérica de uma viga com entalhe, analisada pelo método dos elementos finitos e empregando-se na modelagem constitutiva os conceitos da Mecânica da Fratura aplicada ao concreto. As vigas foram moldadas e ensaiadas no Instituto Politécnico do Rio de Janeiro (IPRJ) da Universidade do Estado do Rio de Janeiro (UERJ) na cidade de Nova Friburgo. Os ensaios foram realizados com controle de deslocamento da célula de carga. Foram ensaiadas três séries de 12 vigas, com quatro dimensões diferentes, geometricamente proporcionais, e três amostras para cada dimensão, totalizando 36 vigas. As alturas utilizadas para as vigas foram 38, 76, 152 e 304 mm, e sua espessura foi mantida constante igual a 38 mm. Os corpos de prova cilíndricos, para caracterização da resistência à compressão do concreto, foram moldados no IPRJ e rompidos no laboratório de engenharia civil da UERJ, na cidade do Rio de Janeiro. Os concretos utilizados apresentaram resistência à compressão média de 70 MPa. / The evolution of the concrete mixes used during the last decades gave birth to the High Performance Concrete (HPC), which, among its main characteristics, presents high strength and low permeability. With the development of chemical products used in civil engineering constructions, mainly the superplasticizers, the use of this kind of concrete has become more and more frequent due to the possibility of obtaining a workable mixture with a water/cement ratio lower than 0.35. Due to its more homogeneous microstructure, the HPC presents a more fragile behavior than the conventional concrete, demanding a better characterization of the material. At the end of the 1970s, concepts of the Fracture Mechanics started to be used for the analysis of the structural behavior of concrete structures. As the nominal stress of the material decreases as the size of the structure increases, it became necessary to consider this size effect in the analysis in order to obtain more suitable levels of security. This fact justifies the use of the Fracture Mechanics in the structural analysis of concrete structures. In this work, the fracture energy was experimentally obtained using the work-offracture method and the size effect method by performing three-point bend tests in HPC notched beams. It was also developed a numerical simulation of the tests, performing the analysis through the Finite Element Method and applying the concepts of the Fracture Mechanics of Concrete into the constitutive model. The notched beams were molded and tested at the Polytechnic Institute of the State University of Rio de Janeiro (IPRJ/UERJ), located in the city of Nova Friburgo. The tests were controlled by the vertical displacement of the load cell. Three series of twelve beams with four geometrically similar sizes were tested. Three samples for each size were cast, making an amount of 36 beams. The beams were 38, 76, 152 and 304 millimeters high and the width was kept constant equal to 38 millimeters. To characterize the concrete compression strength, 100x200 millimeters cylinders were molded at the IPRJ and tested at the UERJ civil engineering laboratory in the city of Rio de Janeiro. The tested concretes presented a medium compressive strength of 70 MPa.