Amine degradation in aqueous amine scrubbing systems for capturing CO₂ from coal fired power plants is a major problem. Oxygen in the flue gas is the major cause of solvent deterioration, which increases the cost of CO₂ capture due to reduced capacity, reduced rates, increased corrosion, solvent makeup, foaming, and reclaiming. Degradation also produces environmentally hazardous materials: ammonia, amides, aldehydes, nitramines, and nitrosamines. Thus it is important to understand and mitigate amine oxidation in industrial CO₂ capture systems. A series of lab-scale experiments was conducted to better understand the causes of and solutions to amine oxidation. This work included determination of rates, products, catalysts, and inhibitors for various amines at various conditions. Special attention was paid to understanding monoethanolamine (MEA) oxidation, whereas oxidation of piperazine (PZ) and other amines was less thorough. The most important scientific contribution of this work has been to show that amine oxidation in real CO₂ capture systems is much more complex than previously believed, and cannot be explained by mass transfer or reaction kinetics in the absorber by itself, or by dissolved oxygen kinetics in the cross exchanger. An accurate representation of MEA oxidation in real systems must take into account catalysts present (especially Mn and Fe), enhanced oxygen mass transfer in the absorber as a function of various process conditions, and possibly oxygen carriers other than dissolved oxygen in the cross exchanger and stripper. Strategies for mitigating oxidative degradation at low temperature, proposed in this and previous work are less effective or ineffective with high temperature cycling, which is more representative of real systems. In order of effectiveness, these strategies are: selecting an amine resistant to oxidation, reduction of dissolved metals in the system, reduction of the stripper temperature, reduction of the absorber temperature, and addition of a chemical inhibitor to the system. Intercooling in the absorber can reduce amine oxidation and improve energy efficiency, whereas amine oxidation should be considered in choosing the optimal stripper temperature. In real systems, 2-amino-2-methyl-1-propanol (AMP) is expected to be the most resistant to oxidation, followed by PZ and PZ derivatives, then methyldiethanolamine (MDEA), and then MEA. MEA oxidation with high temperature cycling is increased 70% by raising the cycling temperature from 100 to 120 °C, the proposed operational temperature range of the stripper. PZ oxidation is increased 100% by cycling to 150 °C as opposed to 120 °C. Metals are expected to increase oxidation in MEA and PZ with high temperature cycling by 40 - 80%. Inhibitor A is not expected to be effective in real systems with MEA or with PZ. MDEA is also not effective as an inhibitor in MEA, and chelating agents diethylenetriamine penta (acetic acid) (DTPA) and 2,5-dimercapto-1,3,4-thiadiazole (DMcT) are only mildly effective in MEA. Although MEA oxidation in real systems cannot be significantly reduced by any known additives, it can be accurately monitored on a continuous basis by measuring ammonia production from the absorber. Ammonia production was shown to account for two-thirds of nitrogen in degraded MEA at low temperature and with high temperature cycling, suggesting that it is a reliable indicator of MEA oxidation under a variety of process conditions. A proposed system, which minimizes amine oxidation while maintaining excellent rate and thermodynamic properties for CO₂ capture would involve use of 4 m AMP + 2 m PZ as a capture solvent with the stripper at 135 °C, intercooling in the absorber, and use of a corrosion inhibitor or continuous metals removal system. Reducing (anaerobic) conditions should be avoided to prevent excessive corrosion from occurring and minimize the amount of dissolved metals. This system is expected to reduce amine oxidation by 90-95% compared with the base case 7 m MEA with the stripper at 120 °C. / text

No description available.

A range of porous solid adsorbents were synthesised and their ability to separate and capture carbon dioxide (CO2) from gas mixtures was examined. CO2 separation from flue gas – a type of exhaust gas from fossil fuel combustion that consists of CO2 mixed with mainly nitrogen and biogas (consists of CO2 mixed with mainly methane) were explicitly considered. The selected adsorbents were chosen partly due to their narrow pore sizes. Narrow pores can differentiate gas molecules of different sizes via a kinetic separation mechanism: a large gas molecule should find it more difficult to enter a narrow pore. CO2 has the smallest kinetic diameter in zeolites when compared with the other two gases in this study. Narrow pore adsorbents can therefore, show enhanced kinetic selectivity to adsorb CO2 from a gas mixture. The adsorbents tested in this study included mixed cation zeolite A, zeolite ZK-4, a range of aluminophosphates and silicoaluminophosphates, as well as two types of titanium silicates (ETS-4, CTS-1). These adsorbents were compared with one another from different aspects such as CO2 capacity, CO2 selectivity, cyclic performance, working capacity, cost of synthesis, etc. Each of the tested adsorbents has its advantages and disadvantages. Serval phosphates were identified as potentially good CO2 adsorbents, but the high cost of their synthesis must be addressed in order to develop these adsorbents for applications. / <p>At the time of the doctoral defence the following papers were unpublished and had a status as follows: Papers 4-8: Manuscripts.</p>

No description available.

The ever increasing global demand for materials has placed aluminium as the world’s second most used metal, with world annual production currently >24 million tons. Consequently, the global alumina industry is perpetually striving to meet demands in conjunction with research, development and implementation of more efficient and sustainable processes and practises. Of specific concern for many proponents within the industry is that increased alumina production inadvertently results in increased Bayer Process-derived alkaline solid and liquid waste loads. Furthermore, in-house power generation at all Australian alumina refineries contributes to acid gas emissions, particularly SOx and NOx, both of which have environmental and anthropogenic impacts of global concern. The focus of this work is SO2 emission. SOx emission control measures can be achieved before, during or after combustion; the latter is termed flue gas desulphurisation (FGD). Commercially available FGD systems are dominated by once-through wet processes whereby the flue gas passes up through an absorbtion tower. The most favourable medium for industrial use is seawater, followed by limestone, and in some cases, a combination of both. However, the ever-increasing stringency of environmental emission legislation continues to inflict tighter controls on power production and is forcing industry to investigate alternative cost-effective FGD mediums. Therefore much research is currently dedicated to the utilisation of high volume, alkaline waste streams over manufactured sorbents. Modern environmental engineering approaches to waste product minimisation, neutralisation and/or reuse have lead to many new processes which change the view of many materials from waste product to environmental resource. Subsequently, this work examines the application of an isolated Bayer Process waste product, tricalcium aluminate hexahydrate (TCA6), as a FGD medium. Initial research assessed the dissolution behaviour and performance of the proposed medium with sulphuric acid, followed by batch reactor trials with a simulated flue gas. Data derived from this research indicated the suitability of TCA6 as a FGD medium and was subsequently applied to a preliminary model and proposed design parameters required for further pilot scale investigations. This work provides strong support for an economically viable and more sustainable approach to FGD for the alumina industry.

The ever increasing global demand for materials has placed aluminium as the world’s second most used metal, with world annual production currently >24 million tons. Consequently, the global alumina industry is perpetually striving to meet demands in conjunction with research, development and implementation of more efficient and sustainable processes and practises. Of specific concern for many proponents within the industry is that increased alumina production inadvertently results in increased Bayer Process-derived alkaline solid and liquid waste loads. Furthermore, in-house power generation at all Australian alumina refineries contributes to acid gas emissions, particularly SOx and NOx, both of which have environmental and anthropogenic impacts of global concern. The focus of this work is SO2 emission. SOx emission control measures can be achieved before, during or after combustion; the latter is termed flue gas desulphurisation (FGD). Commercially available FGD systems are dominated by once-through wet processes whereby the flue gas passes up through an absorbtion tower. The most favourable medium for industrial use is seawater, followed by limestone, and in some cases, a combination of both. However, the ever-increasing stringency of environmental emission legislation continues to inflict tighter controls on power production and is forcing industry to investigate alternative cost-effective FGD mediums. Therefore much research is currently dedicated to the utilisation of high volume, alkaline waste streams over manufactured sorbents. Modern environmental engineering approaches to waste product minimisation, neutralisation and/or reuse have lead to many new processes which change the view of many materials from waste product to environmental resource. Subsequently, this work examines the application of an isolated Bayer Process waste product, tricalcium aluminate hexahydrate (TCA6), as a FGD medium. Initial research assessed the dissolution behaviour and performance of the proposed medium with sulphuric acid, followed by batch reactor trials with a simulated flue gas. Data derived from this research indicated the suitability of TCA6 as a FGD medium and was subsequently applied to a preliminary model and proposed design parameters required for further pilot scale investigations. This work provides strong support for an economically viable and more sustainable approach to FGD for the alumina industry.

The ever increasing global demand for materials has placed aluminium as the world’s second most used metal, with world annual production currently >24 million tons. Consequently, the global alumina industry is perpetually striving to meet demands in conjunction with research, development and implementation of more efficient and sustainable processes and practises. Of specific concern for many proponents within the industry is that increased alumina production inadvertently results in increased Bayer Process-derived alkaline solid and liquid waste loads. Furthermore, in-house power generation at all Australian alumina refineries contributes to acid gas emissions, particularly SOx and NOx, both of which have environmental and anthropogenic impacts of global concern. The focus of this work is SO2 emission. SOx emission control measures can be achieved before, during or after combustion; the latter is termed flue gas desulphurisation (FGD). Commercially available FGD systems are dominated by once-through wet processes whereby the flue gas passes up through an absorbtion tower. The most favourable medium for industrial use is seawater, followed by limestone, and in some cases, a combination of both. However, the ever-increasing stringency of environmental emission legislation continues to inflict tighter controls on power production and is forcing industry to investigate alternative cost-effective FGD mediums. Therefore much research is currently dedicated to the utilisation of high volume, alkaline waste streams over manufactured sorbents. Modern environmental engineering approaches to waste product minimisation, neutralisation and/or reuse have lead to many new processes which change the view of many materials from waste product to environmental resource. Subsequently, this work examines the application of an isolated Bayer Process waste product, tricalcium aluminate hexahydrate (TCA6), as a FGD medium. Initial research assessed the dissolution behaviour and performance of the proposed medium with sulphuric acid, followed by batch reactor trials with a simulated flue gas. Data derived from this research indicated the suitability of TCA6 as a FGD medium and was subsequently applied to a preliminary model and proposed design parameters required for further pilot scale investigations. This work provides strong support for an economically viable and more sustainable approach to FGD for the alumina industry.

Thesis (Ph.D)--Chemical Engineering, Georgia Institute of Technology, 2008. / Committee Chair: Jones, Christopher; Committee Member: Koros, William; Committee Member: Lyon, Andrew; Committee Member: Nair, Sankar; Committee Member: Weck, Marcus. Part of the SMARTech Electronic Thesis and Dissertation Collection.

Thesis (Ph. D.)--University of Alabama at Birmingham, 2009. / Additional advisors: Heng Ban, Chih-Hsiung Cheng, Thomas K. Gale, Melinda M. Lalor. Description based on contents viewed June 3, 2009; title from PDF t.p. Includes bibliographical references (p. 113-123).

Thesis (Ph.D.)--University of Wyoming, 2009. / Title from PDF title page (viewed on May 21, 2010). Includes bibliographical references (p. 50-63).