1 |
Nanoscale measurements of the mechanical properties of lipid bilayersKöcher, Paul Tilman January 2014 (has links)
Lipid bilayers form the basis of the membranes that serve as a barrier between a cell and its physiological environment. Their physical properties make them ideally suited for this role: they are extremely soft with respect to bending but essentially incompressible under lateral tension, and they are quite permeable to water but essentially impermeable to ions which allows the rapid establishment of the osmotic gradients. The function of membrane proteins, which are vital for tasks ranging from signal transduction to energy conversion, depends on their interactions with the lipid environment. Because of the complexity of natural membranes, model systems consisting of simpler lipid mixtures have become indispensable tools in the study of membrane biophysics. The objective of the work reported here is to develop a deeper understanding of the underlying physics of lipid bilayers through nanoscale measurements of the mechanical properties of mixed lipid systems including cholesterol, a key ingredient of cell membranes. Atomic force microscopy (AFM) has been used extensively to measure the topographical and elastic properties of supported lipid bilayers displaying complex phase behaviour and containing mixtures of important PC, PE lipids and cholesterol. Phase transformations have been investigated varying the membrane temperature, and the effects of cholesterol in controlling membrane fluidity, phase, and energetics have been studied. Elastic modulus measurements were correlated with phase behaviour observations. To aid in the nanoscale probing of lipid bilayers, AFM probes with a high aspect ratio and tip radii of $sim$4~nm were fabricated and characterised. These probes were used to investigate the phase boundary in binary and ternary lipid systems, leading to the discovery of a raised region at the boundary which has implications for the localisation of reconstituted proteins as well as the role of natural domains or lipid rafts. The electrical properties of the probes were examined to assess their potential application for combined structural and electrical measurements in liquid. A novel technique was developed to aid in the study of the physical properties of lipid bilayers. Membrane budding was induced above microfabricated substrates through osmotic pressure. Modification of the adhesion energy of the bilayer through biotin-avidin linking was successful in modulating budding behaviour of liquid disordered bilayers. The free energy of the system was modelled to allow quantitative information to be extracted from the data.
|
2 |
Force measurements using scanning probe microscopy : Applications to advanced powder processingMeurk, Anders January 2000 (has links)
The object of this thesis is to apply scanning probemicroscopy (SPM) to the field of advanced powder processing.Measurement of interparticle surface forces at conditionsrelevant to ceramic processing has been performed together withthorough studies of powder friction. Surface force measurements between silicon nitride andsilica surfaces in 1-bromonaphtalene and diiodomethane resultedin an attractive van der Waals force in both media for thesymmetric systems and a repulsive van der Waals force for theasymmetric systems. This agreed well with theoreticalpredictions from Lifshitz theory. Measurements in electrolytesolutions between silicon nitride surfaces with a varyingdegree of oxidation showed that silanol groups dominated theinteractions at a high degree of oxidation, whereas theinfluence of amine species became stronger after surfaceetching. Surface charge, surface potential and density ofsurface groups have been extracted from DLVO computer modellingof the experimental force curves. Surface force measurementshave been carried out using a nitrided silica sphere as acolloidal probe, representative for commercial silicon nitridepowders. Adsorption of poly(acrylic acid) above the isoelectricpoint generated a thin polymer layer of an essentially flatconformation. Friction force measurements were attainable via novelcalibration procedures of both the lateral photodetectorresponse and the cantilever torsional spring constant.Combining the method for detector calibration with evaluationof static friction slopes simplified the choice of appropriatecontact mechanics theory to evaluate the friction measurements.Applying the method on friction measurements between ironsurfaces coated with commercial lubricants showed a substantialsurface deformation not seen from the friction force alone. Thenanorheological properties of silica surfaces coated with twodifferent stearic acids have been evaluated from friction forcemeasurements. Steady sliding motion was replaced by highlyregular stick-slip motion at a critical load and velocity. Thestick-slip motion was successfully described and fitted to aphenomenological model. The contact area evaluated fromMaugis-Dugdale theory revealed the contact diameter to be veryclose to the stick-slip periodicity. Friction measurements were carried out between individualspray-dried ceramic granules as a function of binderconcentration and relative humidity. The hygroscopic nature ofthe binder resulted in a higher adhesion force but lowerfriction coefficient with increasing humidity. This effect wasascribed to softening of the binder and a lowering of the shearstrength of the binder rich surface layer on the granules.Comparison of the friction force between two granules and agranule and a hard metal surface confirmed that resistance toflow during the initial stages of powder pressing is dominatedby granule-wall friction and adhesion. Keywords: Atomic force microscope, AFM, SPM, van der Waalsinteraction, DLVO-theory, surface forces, colloidal probe,force curve, friction, adhesion, stick-slip, cantilever,calibration, spring constant, silicon nitride, iron,silica.
|
3 |
Force measurements using scanning probe microscopy : Applications to advanced powder processingMeurk, Anders January 2000 (has links)
<p>The object of this thesis is to apply scanning probemicroscopy (SPM) to the field of advanced powder processing.Measurement of interparticle surface forces at conditionsrelevant to ceramic processing has been performed together withthorough studies of powder friction.</p><p>Surface force measurements between silicon nitride andsilica surfaces in 1-bromonaphtalene and diiodomethane resultedin an attractive van der Waals force in both media for thesymmetric systems and a repulsive van der Waals force for theasymmetric systems. This agreed well with theoreticalpredictions from Lifshitz theory. Measurements in electrolytesolutions between silicon nitride surfaces with a varyingdegree of oxidation showed that silanol groups dominated theinteractions at a high degree of oxidation, whereas theinfluence of amine species became stronger after surfaceetching. Surface charge, surface potential and density ofsurface groups have been extracted from DLVO computer modellingof the experimental force curves. Surface force measurementshave been carried out using a nitrided silica sphere as acolloidal probe, representative for commercial silicon nitridepowders. Adsorption of poly(acrylic acid) above the isoelectricpoint generated a thin polymer layer of an essentially flatconformation.</p><p>Friction force measurements were attainable via novelcalibration procedures of both the lateral photodetectorresponse and the cantilever torsional spring constant.Combining the method for detector calibration with evaluationof static friction slopes simplified the choice of appropriatecontact mechanics theory to evaluate the friction measurements.Applying the method on friction measurements between ironsurfaces coated with commercial lubricants showed a substantialsurface deformation not seen from the friction force alone. Thenanorheological properties of silica surfaces coated with twodifferent stearic acids have been evaluated from friction forcemeasurements. Steady sliding motion was replaced by highlyregular stick-slip motion at a critical load and velocity. Thestick-slip motion was successfully described and fitted to aphenomenological model. The contact area evaluated fromMaugis-Dugdale theory revealed the contact diameter to be veryclose to the stick-slip periodicity.</p><p>Friction measurements were carried out between individualspray-dried ceramic granules as a function of binderconcentration and relative humidity. The hygroscopic nature ofthe binder resulted in a higher adhesion force but lowerfriction coefficient with increasing humidity. This effect wasascribed to softening of the binder and a lowering of the shearstrength of the binder rich surface layer on the granules.Comparison of the friction force between two granules and agranule and a hard metal surface confirmed that resistance toflow during the initial stages of powder pressing is dominatedby granule-wall friction and adhesion.</p><p>Keywords: Atomic force microscope, AFM, SPM, van der Waalsinteraction, DLVO-theory, surface forces, colloidal probe,force curve, friction, adhesion, stick-slip, cantilever,calibration, spring constant, silicon nitride, iron,silica.</p>
|
Page generated in 0.0468 seconds