A parallel finite element code with adaptive meshing was developed and used to study three dimensional, time-dependent fluid flows caused by thermocapillary convection as well as temperature and dopant distribution in fusion welding and floating zone crystal growth. A comprehensive numerical model of the three dimensional time-dependent fluid flows in a weld pool had been developed. This model considered most of the physical mechanisms involved in gas tungsten arc welding. The model helped obtaining the actual chaotic time-dependent melt flow. It was found that the fluid flow in the weld pool was highly complex and influenced the weld pool’s depth and width. The physicochemical model had also been studied and applied numerically in order to simulate the surfactant adsorption onto the surface effect to the surface tension of the metal liquid in a weld pool. Another model, a three dimensional time-dependent, with adaptive mesh refinement and coarsening was applied for simulating the effect of weak flow on the radial segregation in floating zone crystal growth. The phase change equation was also included in this model in order to simulate the real interface shape of floating zone. In the new parallel code, a scheme that keeps the level of node and face instead of the complete history of refinements was utilized to facilitate derefinement. The information was now local and the exchange of information between each and every processor during the derefinement process was minimized. This scheme helped to improve the efficiency of the parallel adaptive solver. / QC 20100527

<p>U disertaciji je prikazan odabir rastvarača, veličine, vrste i udela čestica za aktivni premaz namenjen postizanju povećane dubine uvara na austenitnom nerđajućem čeliku pri zavarivanju netopljivom elektrodom u zaštiti inertnog gasa. Pored sastava aktivnog premaza, u disertaciji je izvršena optimizacija: geometrije elektrode, jačine struje i brzine zavarivanja. Nakon odabira perspektivnih tipova sastava premaza i parametara zavarivanja, na zavarenim uzorcima izvršena je karakterizacija mehaničkih osobina, hemijskog sastava i mikrostrukture.</p> / <p>In this doctoral thesis, the selection of solvent, size, type and the content of<br />oxide particles in activated flux aimed at increasing the penetration on<br />austenitic stainless steel in gas tungsten arc welding is presented. Besides<br />activated flux composition, the optimization of welding parameters such as<br />electrode geometry, welding current and welding speed was done. After the<br />selection of successful activated flux formulations and welding parameters,<br />the characterization of mechanical properties, chemical composition and<br />microstructure was determined.</p>

Welding is used extensively in aerospace, automotive, chemical, manufacturing, electronic and power-generation industries. Thermally-induced residual stresses due to welding can significantly impair the performance and reliability of welded structures. Numerical simulation of weld pool dynamics is important as experimental measurements of velocities and temperature profiles are difficult due to the small size of the weld pool and the presence of the arc. From a structural integrity perspective of welded structures, it is necessary to have an accurate spatial and temporal thermal distribution in the welded structure before stress analysis is performed. Existing research on weld pool dynamics simulation has ignored the effect of fluid flow in the weld pool on the temperature field of the welded joint. Previous research has established that the weld pool depth/width (D/W) ratio and Heat Affected Zone (HAZ) are significantly altered by the weld pool dynamics. Hence, for a more accurate estimation of the thermally-induced stresses it is desired to incorporate the weld pool dynamics into the analysis. Moreover, the effects of microstructure evolution in the HAZ on the mechanical behavior of the structure need to be included in the analysis for better mechanical response prediction. In this study, a three-dimensional model for the thermo-mechanical analysis of Gas Tungsten Arc (GTA) welding of thin stainless steel butt-joint plates has been developed. The model incorporates the effects of thermal energy redistribution through weld pool dynamics into the structural behavior calculations. Through material modeling the effects of microstructure change/phase transformation are indirectly included in the model. The developed weld pool dynamics model includes the effects of current, arc length, and electrode angle on the heat flux and current density distributions. All the major weld pool driving forces are included, namely surface tension gradient, plasma drag force, electromagnetic force, and buoyancy. The weld D/W predictions are validated with experimental results. They agree well. The effects of welding parameters (like welding speed, current, arc length, etc.) on the weld D/W ratio are documented. The workpiece deformation and stress distributions are also highlighted. The transverse and longitudinal residual stress distribution plots across the weld bead and their variations with welding speed and current are also provided. The mathematical framework developed here serves as a robust tool for better prediction of weld D/W ratio and thermally-induced stress evolution and distribution in a welded structure by coupling the different fields in a welding process. / Ph. D.

Welding of duplex stainless steel pipeline material for the oil and gas industry is now common practice. To date, research has been conducted primarily on the parent material and heat affected zones in terms of its susceptibility to various forms of corrosion. However, there has been little research conducted on the degree of sensitisation of the various successive weld layers, namely the root, fill and cap layers. The focus of this research study was to: (i) provide an in-depth microstructural analysis of the various weld passes, (ii) study the mechanical properties of the weld regions; (iii) determine degree of sensitisation of the various weld passes; and (iv) investigate the residual stress levels within the various regions/ phases of the welds. Four test conditions were prepared using manual Gas Tungsten Arc Welding with 'V' and 'U' bevel configuration. Structural analysis consisted of (i) optical microscopy, scanning electron microscopy and magnetic force microscopy; (ii) ferrite determination using Magna-Gauge, Fischer Ferrite-scope and Point Count method. Mechanical testing consisted of Vickers hardness measurements, Charpy impact studies and transverse tensile testing. The degree of sensitisation was determined by three test methods: a modified ASTM A262, ASTM A923 and a modified Double Loop Electrochemical Potentiodynamic Reactivation (DL-EPR) test. Residual stress levels were determined using two neutron diffraction techniques: a reactor source and a time of flight spallation source. Microstructure observed by optical microscopy and magnetic force microscopy shows the formation of both fine and coarse structures within the weld metal. There was no evidence of secondary austenite, being present in any of the weld metal conditions examined. In addition, no detrimental intermetallic phases or carbides were present. The DL-EPR test results revealed that the fill layer regions for all four conditions and the base material showed the highest values for Ir/Ia and Qr/Qa. All four test conditions passed the ASTM A262 and A923 qualitative type tests, even under restricted and modified conditions. Residual stress measurements by neutron diffraction conducted at Lucas Heights Hi-Flux Reactor revealed that the ferrite phase stress was tensile in the heat affected zones and weld, and appeared to be balanced by a local compressive austenite phase stresses in the normal and transverse directions. Residual stress measurements by neutron diffraction conducted at Los Alamos Nuclear Science Centre revealed that in the hoop direction, ferrite (211) and austenite (311) exhibit tensile strains in the weld. In the axial and radial direction, the strains for both phases were more compressive. Correlations between the degree of sensitization and microstructural changes / ferrite content were observed. Higher degrees of sensitization (Ir/Ia and Qr/Qa) were associated with reduced ferrite (increased austenite) content. Correlations between the stresses generated, the evolved microstructures and degree of sensitization were evident. Stresses within the cap region were generally shown to be of a tensile nature in the transverse and longitudinal direction. In summary, the study has shown that correlations exist between the weld microstructure, susceptibility to sensitisation and levels / distribution of internal stresses within the weld regions.

Submitted by Claudinei Pracidelli (cpracide@ipen.br) on 2016-11-11T09:40:30Z No. of bitstreams: 0 / Made available in DSpace on 2016-11-11T09:40:30Z (GMT). No. of bitstreams: 0 / A soldagem tem grande importância no setor metroferroviário, pois é empregada na fabricação de componentes estruturais e no acabamento de vagões de passageiros, que em sua maior parte são de aço inoxidável. As juntas soldadas podem apresentar descontinuidades que são interrupções que afetam as propriedades mecânicas e metalúrgicas da junta soldada. A presença destas descontinuidades, dependendo do seu tamanho, natureza ou efeito combinado, pode ocasionar a reprovação da junta soldada, quer pela redução de propriedades mecânicas ou pela não aceitação, segundo critérios estabelecidos em normas. Uma estrutura que tenha uma solda reprovada durante sua qualificação ou inspeção, pela presença de descontinuidades pode ser recuperada, por meio de um retrabalho a ser realizado nesta junta. A refusão do cordão de solda por meio do processo TIG (Tungsten Inert Gas), sem a utilização do material de adição, é uma técnica de retrabalho que pode ser empregada, em especial pela viabilidade técnica e econômica do processo. Neste estudo analisou-se a influência que o processo de reparo por soldagem TIG exerceu no comportamento mecânico e microestrutural das juntas soldadas pelo processo MIG, por meio de: ensaios mecânicos (tração, fadiga e microdureza Vickers), ensaios não destrutivos (inspeção visual e líquidos penetrantes) e caracterização microestrutural do cordão de solda. Resultados das amostras de ensaio de tração e fadiga indicaram que o reparo dos cordões de solda não alterou o comportamento mecânico das juntas. As juntas submetidas ao reparo nas quais foram retirados os reforços dos cordões apresentaram modificações nas propriedades mecânicas, mas também apresentaram resultados satisfatórios. / Dissertação (Mestrado em Tecnologia Nuclear) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

No description available.

No description available.

Additive Manufacturing (AM) is an innovative manufacturing process which offers near-net shape fabrication of complex components, directly from CAD models, without dies or substantial machining, resulting in a reduction in lead-time, waste, and cost. For example, the buy-to-fly ratio for a titanium component machined from forged billet is typically 10-20:1 compared to 5-7:1 when manufactured by AM. However, the production rates for most AM processes are relatively slow and AM is consequently largely of interest to the aerospace, automotive and biomedical industries. In addition, the solidification conditions in AM with the Ti alloy commonly lead to undesirable coarse columnar primary β grain structures in components. The present research is focused on developing a fundamental understanding of the influence of the processing conditions on microstructure and texture evolution and their resulting effect on the mechanical properties during additive manufacturing with a Ti6Al4V alloy, using three different techniques, namely; 1) Selective laser melting (SLM) process, 2) Electron beam selective melting (EBSM) process and, 3) Wire arc additive manufacturing (WAAM) process. The most important finding in this work was that all the AM processes produced columnar β-grain structures which grow by epitaxial re-growth up through each melted layer. By thermal modelling using TS4D (Thermal Simulation in 4 Dimensions), it has been shown that the melt pool size increased and the cooling rate decreased from SLM to EBSM and to the WAAM process. The prior β grain size also increased with melt pool size from a finer size in the SLM to a moderate size in EBSM and to huge grains in WAAM that can be seen by eye. However, despite the large difference in power density between the processes, they all had similar G/R (thermal gradient/growth rate) ratios, which were predicted to lie in the columnar growth region in the solidification diagram. The EBSM process showed a pronounced local heterogeneity in the microstructure in local transition areas, when there was a change in geometry; for e.g. change in wall thickness, thin to thick capping section, cross-over’s, V-transitions, etc. By reconstruction of the high temperature β microstructure, it has been shown that all the AM platforms showed primary columnar β grains with a <001>β.