1 |
Investigation into the feasibility of a four valve per cylinder lean burn port fuel injected stratified charge combustion systemPlatts, Kieron Charles January 2000 (has links)
No description available.
|
2 |
Liquid fuel spray characteristicsSavic, Sasha January 2000 (has links)
No description available.
|
3 |
Experimental research on particulate matter emissions from gasoline direct injection enginesXu, Fan January 2012 (has links)
As the legislation on vehicle emissions is becoming more and more stringent, increasing attention has been paid to the fine particles emitted by diesel and gasoline vehicles. The high number emission of fine particles has been shown to have a large impact on the atmospheric environment and human health. Researchers have shown that gasoline engines, especially Gasoline Direct Injection (GDI) engines, tend to emit large amounts of small size particles compared to Port Fuel Injection (PFI) gasoline engines and diesel engines fitted with Diesel Particulate Filters (DPFs). As a result, the particle number emissions of GDI engines will be restricted by the EU6 legislation. The particulate emission level of GDI engines means that they would face some challenges in meeting the EU6 requirement. This thesis undertakes research in the following area. Firstly, the filtration efficiencies of glass fibre filters were quantified using a Cambustion Differential Mobility Spectrometer 500 (DMS500) to see if all of the particles from the sampled gas can be collected by the filters. Secondly, various valve timings and different injection modes such as double injection with a second injection after compression, single early injection and split early injection were implemented to measure the Particulate Matter (PM) emissions and combustion characteristics of a GDI engine under warm-up operating conditions. Thirdly, the techniques for removing volatile particles were investigated using a catalytic Volatile Particle Remover (VPR) and an Evaporation Tube (ET) with hot air dilution under various test conditions. The results show that for the glass fibre filters tested here, the transmission efficiencies of the particles are very low, indicating that PM sampling using fibre filters is an effective method of studying the particulate emissions from the engine. Particle number emissions using double injection with injection after compression were much higher than those with single injection during the intake stroke. Under 1200 rpm, 110 Nm cold engine operation, no reduction effect on PM emissions was shown by using split intake injection to further facilitate homogeneous mixture formation compared with single intake injection. Valve timings showed moderate effects on particulate emissions. Properly adjusted timing for exhaust valve closure led to reduced particulate emissions by a factor of about 2 and the combustion characteristics were not adversely affected much. The VPR temperature and exhaust residence time did not show much effect on the catalytic VPR performance once the mass flow rate of exhaust was above 0.09 g/s. Generally, the transmission efficiencies of the VPR follow the trends of the scaled PMP counting efficiency specification. Hot air dilution is effective in reducing the small size particles. At 23 nm, the transmission efficiencies are within the error range of the PMP specification. The catalytic VPR and the Evaporation Tube were all found to be effective in reducing the particle number of small size (nucleation mode) particles. Both systems have some particle loss mainly due to the physical effects of diffusion and thermophoresis. Until now, GDI engines have not been optimised for reducing particulate emissions as the focus has been on gaseous emissions and fuel economy. With careful re-optimisation of the catalyst light-off and engine calibration (especially for transients) then there is scope for GDI engines to meet forthcoming emissions legislation.
|
4 |
Transient microscopy of primary atomization in gasoline direct injection spraysZaheer, Hussain 08 June 2015 (has links)
Understanding the physics governing primary atomization of high pressure fuel sprays is of paramount importance to accurately model combustion in direct injection engines. The small length and time scales of features that characterize this process falls below the resolution power of typical grids in CFD simulations, which necessitates the inclusion of physical models (sub-models) to account for unresolved physics. Unfortunately current physical models for fuel spray atomization used in engine CFD simulations are based on significant empirical scaling because there is a lack of experimental data to understand the governing physics. The most widely employed atomization sub-model used in current CFD simulations assumes the spray atomization process to be dominated by aerodynamically-driven surface instabilities, but there has been no quantitative experimental validation of this theory to date. The lack of experimental validation is due to the high spatial and temporal resolutions required to simultaneously to image these instabilities, which is difficult to achieve.
The present work entails the development of a diagnostic technique to obtain high spatial and temporal resolution images of jet breakup and atomization in the near nozzle region of Gasoline Direct Injection (GDI) sprays. It focuses on the optical setup required to achieve maximum illumination, image contrast, sharp feature detection, and temporal tracking of interface instabilities for long-range microscopic imaging with a high-speed camera. The resolution and performance of the imaging system is characterized by evaluating its modulation transfer function (MTF). The setup enabled imaging of GDI sprays for the entire duration of an injection event (several milliseconds) at significantly improved spatial and temporal resolutions compared to historical spray atomization imaging data. The images show that low to moderate injection pressure sprays can be visualized with a high level of detail and also enable the tracking of features across frames within the field of view (FOV)
|
5 |
Emissions and Climate Impacts of Aerosol Emissions from Cookstoves and Gasoline Direct Injection VehiclesSaliba, Georges 01 February 2018 (has links)
Anthropogenic gas- and particle-phase emissions affect the climate by absorbing and scattering radiation, and have been linked to adverse health effects. Black carbon (BC), a by-product of incomplete combustion, is the most potent light-absorbing component of atmospheric aerosols, with a top-of-the atmosphere direct radiative forcing estimated to be only second to CO2. However, there is a large uncertainty associated with BC’s total direct and indirect radiative forcings due to uncertain source emissions and optical properties and complex interactions with clouds. In this dissertation we investigate the direct radiative impact of two of the most important sources of BC particles: biofuel combustion and vehicles. Together these sources contribute around 40% of the global atmospheric BC burden. Recently, both of these energy sources are undergoing rapid technology changes, and the climate impacts from the emissions of these newly adopted technologies remain uncertain. We also investigate the role of atmospheric processing on the optical properties and growth rates of particles. This dissertation first assesses the climate impacts of aerosol emissions of two rapidly emerging technologies: improved cookstoves and gasoline direct injection (GDI) vehicles. We performed extensive measurements of gas- and particle emissions and optical properties of emissions from both these sources. Our data suggests that improved rocket cookstoves have, on average, a factor of two lower particulate matter (PM) emissions compared to traditional cookstoves but only a 4% climate benefits associated with their emissions. In contrast, we estimated a 30% climate benefit from switching traditional cookstoves to gasifier ones. Of all the stoves tested, charcoal stoves had the lowest emissions and climate impacts. Our data suggests the widespread deployment of improved cookstoves to replace existing, inefficient, traditional cookstoves will likely result in health and climate co-benefits. Similarly, we estimated that the rapid adoption of GDI vehicles to replace existing port fuel injection (PFI) vehicles will likely result in reduced warming from emissions. This is due to the higher fuel economy of GDI engines; we measured an average CO2 reduction of 57 g/mi, from switching engine technologies. GDI engine emissions had higher PM emissions compared to PFI engines, similar to previous findings. In addition, our data suggests that newer GDI engines have a factor of two lower PM emissions compared to older GDI engines. These improvements in emissions may enable GDI-equipped vehicles to meet the new Federal Tier 3 PM standard of 3.0 mg/mi without gasoline particulate filters (GPF, which would reduce their fuel economy). To better constrain the large uncertainty of radiative forcing associated with cookstove emissions, this dissertation examines emissions and optical properties from several cookstove and fuel combinations. We performed extensive laboratory measurements of the optical properties of fresh cookstove emissions using the newly developed firepower sweep protocol. Current model treatments of the optical properties of cookstove emissions assume: (1) complete internal mixture between BC and non-BC material and (2) absorption properties of organics based on parametrizations developed for biomass burning emissions. These assumptions do not accurately represent optical properties of fresh cookstove emissions. We developed new parametrizations of optical properties (BC-mass absorption cross section (MACBC), absorption angstrom exponent (AAE), and single scattering albedo (SSA)) of aerosol emissions from cookstoves as a function of the BC-to-PM mass ratio. These parametrizations are designed for use in climate models to more rigorously assess the global climate implications from adoption of improved stove technologies. Upon entering the atmosphere aerosol emissions undergo complex chemical transformations. Aerosol optical properties depend on their atmospheric processing which controls the amount of coating the particles accumulate and their lifetime. To assess the effects of coating on the optical properties, we performed targeted experiments using real world, size selected, BC particles emitted from a rocket improved cookstove, and coated with biogenic secondary organic aerosol (SOA) material. These experiments explicitly target to evaluate measurements and modeling using simple formulation like Mie theory. Measurements of MACBC and the mass scattering cross section (MSC) of coated BC particles were in good agreement with Mie predictions when the organic-to-BC mass ratio>5. Scattering (but not absorption) was sensitive to BC fractal-like morphology; Mie theory under-predicted measured scattering of fresh emissions. Our data suggest that Mie theory can be used in climate models to approximate the optical properties of coated BC particles emitted from cookstoves, if the mixing-state of BC particles is known. In this dissertation, we present initial evidence that particle growth rates depend on seed composition and gas-phase supersaturation. Current models do not account for seed-dependent growth rates. We conducted experiments to investigate the growth of diesel and biogenic SOA particles. Both seeds were exposed to the same gas-phase supersaturation, which allows us to accurately retrieve differences in growth rates and decouple the effects of surface activity and accommodation coefficients. We estimated that the accommodation coefficients of condensing material was 10% to 30% lower on the diesel particles compared to the SOA particles. Moreover, we measured larger surface activity of condensing material on the diesel particles, potentially due to less-miscible condensing vapors in the diesel particles compared to the SOA particles. Our data suggest that growth of BC (diesel) particles in the atmosphere is likely slower compared to SOA particles. Accurately representing these processes is important to estimate the lifetime and absorption enhancement from coated BC particles, as they compete with other particles for condensable vapors.
|
6 |
System Simulation of Combustion in Direct-Injection Spark-Ignition Engines / Simulation système de la combustion dans les moteurs à allumage commandé à injection directePellegrino, Federico 17 October 2019 (has links)
La présence de contraintes de plus en plus strictes sur les émissions de polluants on poussé les contruteurs vers l'injection directe essence (IDE), afin d'améliorer les performances et réduire la consommation de carburant et les émissions des moteurs à combustion interne. Par conséquent, de nouveaux défis sont introduits en termes d'optimisation de la combustion, en raison d'une plus complexe phénomenologie tandis que les modéles système demande des paramètres de calibration supplémentaires.Cette thèse présente le développement et la validation d'un modèle zéro-dimensionnel (0D) de combustion en IDE pour application en simulation système. Le modèle proposé détaille la physique de l'atomisation, et évaporation des gouttes, de la préparation du mélange air/carburant, de la propagation de flamme dans un mélange non-homogène ainsi que l'intéraction entre ces phénomènes.La phase liquide est discretisés en paquets groupant des gouttes de la même taille.Un modèle d'atomisation empirique basé sur la vitesse d'injection, les propriétés du carburant et les conditions thermodynamiques fournit les diamètres initiaux. Un modèle Lagrangien détaillant une dynamique de trainée/inértie, échange thermique et convection forcée décrit la pénétration liquide et l'evaporation des paquets. La formation du mélange air/carburant est décrite avec une PDF qui discretise la charge en un mécanisme de classes intéragissant les unes avec les autres et avec les paquets de gouttes. La propagation de flamme prend en compte les effets de l'hétérogéneité du mélange sur la vitesse de flamme et la formation des polluants.Le modèle proposé a été implémenté dans la plateforme Simcenter Amesim, dédiée á la modélisation de systémes multi-physiques, et intégrée dans le modèle de combustion essence CFM1D, de la librairie IFP-Engine.Des approche de modélisation de l'evaporation de carburant, de la dynamique de spray et de la formation du mélange, inspirés de la literature sur les moteurs Diesel, ont été adaptés aux conditions IDE.Le modèle a initialement été validé sur des mesures et des simulations RANS 3D réalisées avec le code IFP-C3D, d'une bombe d'injection à volume constant.Un vortex de tumble, dans un premier temps, et des variations rapides du voulume de la chambre ensuite, ont été ajoutés aux expériments numériques afin d'évaluer la réponse du modèle à l'aérodynamique dans la chambre de combustion et à des conditions thermodynamiques variables, en termes d'évaporation, développement du spray et distribution de la richesse. Des simulations d'injections dans un moteur entraîné,dont les résultats ont été comparés avec des mesures et des calculs CDF,complètent la validation du modèle avec à la fois des conditions thermodynamiques variable et de l'aérodynamique. / Future constraints on pollutant emissions pushed car manufacturers towards gasoline direct injection (GDI) technologies to improve engine performances and reduce fuel consumption and emissions. New challenges are then introduced in terms of combustion optimization due to a more complex phenomenology while system models require additional calibration parameters.This PhD work presents the development and validation of a Zero-Dimensional (0D) model of GDI combustion for system simulation. The proposed model focuses on physics of atomization and drop evaporation, fuel/air mixing, flame propagation in heterogeneous charge and mutual interaction between these phenomena.The liquid phase is discretized in parcels grouping drops of the same size. An empirical atomization model based on injection velocity, fuel characteristics and thermodynamic conditions provides initial diameters. A Lagrangian model including drag-inertia dynamics, heat-up and forced convection describes drop parcel penetration and evaporation. Fuel / air mixing is described using a discrete Probability Density Function (PDF) approach, based on constant-mixture-fraction classes interacting with each other and with the drop parcels. Flame propagation takes into account mixture heterogeneity effects on flame speed and pollutant production is modelled.The model was implemented in the Simcenter Amesim platform for multi-physical modelling and integrated in a generic Spark Ignition (SI) combustion chamber submodel, CFM1D, from the IFP-Engine library.Fuel evaporation, spray dynamics and mixture formation modelling approaches, inspired by literature on Diesel engines, were adapted to GDI operating conditions. The model was first validated on a constant-volume vessel with quiescent gas in different thermodynamic conditions by means of experiments and 3D RANS CFD simulations performed with IFP-C3D. A tumble vortex in a constant volume vessel, in a first time, and rapid variations of the vessel volume, in a second time, were then added to the numerical experiment in order to test the model response to in-cylinder flow aerodynamics and variable thermodynamic conditions, respectively, in terms of fuel evaporation, spray development and fuel/air mixing and equivalence ratio distribution. Computations of fuel injections in a motored engine complete the model validation campaign in variable thermodynamic conditions and with realistic aerodynamics and the results were compared to both experiments and CFD computations.
|
7 |
Model Based Investigation of Lean Gasoline PM and NOx ControlShivaprasad, Shreyas January 2014 (has links)
No description available.
|
8 |
Optical analysis of multi-stream GDI sprays under various engine operating conditionsMojtabi, Mehdi January 2011 (has links)
The design and optimisation of a modern gasoline direct injection (GDI) engine requires a thorough understanding of the fuel sprays characteristics and atomisation process.Therefore this thesis presents a detailed optical analysis of atomisation, penetration and interaction of multi-stream GDI sprays under engine relevant pressures and temperatures. The characteristics of the fuel spray in a GDI engine have a great influence on the fuel-air mixing and combustion processes as fuel injectors must provide adequate atomisation for vaporisation of the fuel to take place before combustion is initiated, whilst also avoiding spray impingement on the cylinder walls or piston crown. In this study multi-stream injectors, to be used within GDI engines, are quantified using Laser Doppler Anemometry (LDA) on an atmospheric bench. This process allowed for highly detailed spray analysis of droplet velocities and diameter at precise locations, using a three dimensional traverse, within the injector spray. The aim of the study was to analyse plume interaction between separate plumes of multi-stream injectors. Three multi-stream injectors were subjected to testing; two six-hole injectors and one three-hole injector. The injectors differed by having different distances between the plumes. The effect of fuel type on the liquid break-up and atomisation was investigated using Phase Doppler Anemometry (PDA) and Mie imaging. Mie imaging was also performed to capture images of fuel from a multi-stream injector as it was sprayed into a pressure chamber which was used to recreate the conditions found in an engine likely to cause flash boiling. In total, five variables were investigated: fuel pressure, ambient pressure, ambient temperature, fuel composition and injector geometry. Once processed, the recorded images allowed measurement of spray tip penetration and cone angle. Qualitative data on the change in shape of the spray was also available. The results showed that flash boiling has potential to reduce droplet diameters and improve fuel vaporisation, however, the associated change in spray shape must be taken into account to avoid problems with spray impingement. Keywords: Gasoline Direct Injection, multi-stream injector, atomisation, penetration, cone angle, Mie imaging, Phase Doppler Anemometry, flash boiling.
|
9 |
Methodology of Measuring Particulate Matter Emissions from a Gasoline Direct Injection EngineMireault, Phillip 19 March 2014 (has links)
A gasoline direct injection engine was set-up to operate with a dynamometer in a test cell. Test cycle and emissions measurement procedures were developed for evaluating the regulated and non-regulated
gaseous emissions. Equipment and techniques for particulate matter measurements were adapted for use with the gasoline direct injection engine. The particulate matter emissions produced by the engine were compared between two different fuels; gasoline and E10 (10% ethanol and 90% gasoline). The gaseous emissions generated by the engine when it was run on gasoline and E30 (30% ethanol and 70% gasoline) were also compared. Particle number decreased with E10 for hot start conditions, while the opposite was observed for cold start conditions. Particulate matter emissions were found to track with acetylene and ethylene emissions.
|
10 |
Methodology of Measuring Particulate Matter Emissions from a Gasoline Direct Injection EngineMireault, Phillip 19 March 2014 (has links)
A gasoline direct injection engine was set-up to operate with a dynamometer in a test cell. Test cycle and emissions measurement procedures were developed for evaluating the regulated and non-regulated
gaseous emissions. Equipment and techniques for particulate matter measurements were adapted for use with the gasoline direct injection engine. The particulate matter emissions produced by the engine were compared between two different fuels; gasoline and E10 (10% ethanol and 90% gasoline). The gaseous emissions generated by the engine when it was run on gasoline and E30 (30% ethanol and 70% gasoline) were also compared. Particle number decreased with E10 for hot start conditions, while the opposite was observed for cold start conditions. Particulate matter emissions were found to track with acetylene and ethylene emissions.
|
Page generated in 0.3839 seconds