In this study, characterization of activated carbon produced from apricot stones by chemical activation technique using phosphoric acid (H3PO4) as activating agent, at relatively low temperatures (300, 400 and 500oC), was investigated. To produce activated carbon acid impregnated samples were heated / at a heating rate of 20oC/min to the final carbonization temperatures, 300oC, 400oC and 500oC. For each temperature four different carbonization time (90, 120, 180 and 210 min.) were used to produce twelve different activated carbons. The pore structures of activated carbons were determined as follows: The volume and area of macropores in the pore diameter range of 8180-50 nm were determined by mercury intrusion porosimetry. Mesopore (in the range of 50-2 nm) areas and volumes were determined by N2 gas adsorption technique at -195.6oC, BET surface areas of the samples were also determined, in the relative pressure range of 0.05 to 0.02, by the same technique. The pore volume and the area of the micropores with diameters less than 2 nm were determined by CO2 adsorption measurements at 0oC by the application of Dubinin Radushkevich equation. N2 (BET) and CO2 (D-R) surface areas of the samples were in the range of 444-709m2/g and 433-650m2/g, respectively. AC4.2 sample (carbonization temperature of 400oC and carbonization time of 120 min.) was found to have the maximum BET and CO2 area as 709m2/g and 650m2/g, respectively. Surface areas of the samples consisting of around 10% mesopores and over 90% micropores. N2 adsorption isotherms also confirm that pores are in the micropore range.

In this study, the pore structures and surface areas of activated carbons produced from hazelnut shell and hazelnut husk by chemical activation technique using phosphoric acid (H3PO4), at relatively low temperatures (300, 400 and 500oC), were investigated. Raw materials were impregnated with different H3PO4 solutions of 30%, 40%, 50% and 60% by weight. To produce activated carbon, acid impregnated samples were heated / at a heating rate of 20 oC/min to the final carbonization temperature and held at that temperature for 2 hours. The volume and surface areas of mesopores (2-50 nm) and BET surface areas of the samples were determined by N2 gas adsorption technique at -195.6oC. The pore volume and the area of the micropores with diameters less than 2 nm were determined by CO2 adsorption measurements at 0oC by the application of Dubinin Radushkevich equation. N2 (BET) surface areas of the hazelnut shell and hazelnut husk based activated carbons were in the range of 242-596 m2/g and 705-1565 m2/g, respectively. CO2 (D-R) surface areas of the hazelnut shell and hazelnut husk based activated carbons were in the range of 433-576 m2/g and 376-724 m2/g, respectively. The highest BET surface area was obtained as 596 m2/g among hazelnut shell based samples (HS 60.4 / shell impregnated with 60 wt.% H3PO4, carbonized at 400 &ordm / C) and as 1565 m2/g among hazelnut husk based samples (HH 40.4 / husk impregnated with 40 wt.% H3PO4, carbonized at 400 &ordm / C). Hazelnut shell based activated carbons were mainly microporous while hazelnut husk based ones were mesoporous.

Com o aumento da população mundial, o desenvolvimento de novas fontes e conversores de energia tornou-se uma necessidade. As células a combustível mostram-se como uma alternativa viável devido principalmente a duas razões, sua alta eficiência e a utilização de combustíveis renováveis. No presente trabalho se estuda a influência da temperatura de operação e o conteúdo de álcali no combustível sobre a densidade de potencia para uma célula a combustível de glicerol direto. Como combustível foi utilizado uma solução de glicerol:KOH (1M:xM, x=0, 1, 3, 5), como membranas foram utilizados filmes de polibencimidazol impregnado com ácido fosfórico (PBI/H3PO4, relação molar 1:11) ou 1-hexil-3-metilimidazol trifluorometanosulfonato (PBI/HMI-Tf relação molar 1:1.5), e finalmente, nano partículas de Pt suportadas em carbono (60% w/w) como catalizador no ânodo e no cátodo. Em geral, o incremento da temperatura e conteúdo de álcali no combustível mostra um efeito favorável na densidade de potencia do sistema. Numa célula a combustível unitária de glicerol direto utilizando membranas de PBI/ H3PO4 e PBI/HMI-Tf foram obtidas densidades de potencia de 0.54mW.cm-2 a 175°C e 0.599mW.cm-2 a 130°C, respectivamente, para uma solução de glicerol de (1M); enquanto que, para uma solução com um conteúdo maior de álcali, glicerol:KOH (1M:5M), foram obtidas densidades de potencia maiores, 44.1mW.cm-2 a 175°C e 29mW.cm-2 a 130°C, respectivamente. O efeito combinado do incremento da temperatura e concentração de álcali no combustível mostra um efeito maior em relação ao efeito só da temperatura. / With the increasing world population, the development of new energy sources or energy converters has become a necessity. Fuel cells show up as a viable alternative due mainly to two reasons, their high efficiency and the use of renewable fuels. In the present work we study the influence of operating temperature and alkali content in the fuel on the power density for a direct glycerol fuel cell. A glycerol:KOH (1M: xM, x = 0, 1, 3, 5) solution was used as fuels, as membranes were used polibencimidazol films impregnated with phosphoric acid (PBI/H3PO4, molar ratio of 1:11) or 1-hexyl-3-methylimidazolium trifluoromethanesulfonate (PBI/HMI-Tf), and finally, Pt nanoparticles supported on carbon (60% w / w) as catalyst in the anode and cathode. In general, increasing the temperature and alkali content in the fuel shows a favorable effect in the system power density. In a direct glycerol fuel cell using PBI/H3PO4 and PBI /HMI-Tf membranes were obtained power density of 0.54mW.cm-2 at 175°C and 0.599mW.cm-2 at 130°C, respectively, for a 1M glycerol solution; while for a glycerol solution with a higher content of alkali, glycerol:KOH (1M: 5M), were obtained higher power densities, 44.1mW.cm-2 at 175 ° C and 29mW.cm-2 at 130 ° C, respectively. The combined effect of increased temperature and alkali concentration in the fuel shows a greater effect compared to the effect of temperature only.

Com o aumento da população mundial, o desenvolvimento de novas fontes e conversores de energia tornou-se uma necessidade. As células a combustível mostram-se como uma alternativa viável devido principalmente a duas razões, sua alta eficiência e a utilização de combustíveis renováveis. No presente trabalho se estuda a influência da temperatura de operação e o conteúdo de álcali no combustível sobre a densidade de potencia para uma célula a combustível de glicerol direto. Como combustível foi utilizado uma solução de glicerol:KOH (1M:xM, x=0, 1, 3, 5), como membranas foram utilizados filmes de polibencimidazol impregnado com ácido fosfórico (PBI/H3PO4, relação molar 1:11) ou 1-hexil-3-metilimidazol trifluorometanosulfonato (PBI/HMI-Tf relação molar 1:1.5), e finalmente, nano partículas de Pt suportadas em carbono (60% w/w) como catalizador no ânodo e no cátodo. Em geral, o incremento da temperatura e conteúdo de álcali no combustível mostra um efeito favorável na densidade de potencia do sistema. Numa célula a combustível unitária de glicerol direto utilizando membranas de PBI/ H3PO4 e PBI/HMI-Tf foram obtidas densidades de potencia de 0.54mW.cm-2 a 175°C e 0.599mW.cm-2 a 130°C, respectivamente, para uma solução de glicerol de (1M); enquanto que, para uma solução com um conteúdo maior de álcali, glicerol:KOH (1M:5M), foram obtidas densidades de potencia maiores, 44.1mW.cm-2 a 175°C e 29mW.cm-2 a 130°C, respectivamente. O efeito combinado do incremento da temperatura e concentração de álcali no combustível mostra um efeito maior em relação ao efeito só da temperatura. / With the increasing world population, the development of new energy sources or energy converters has become a necessity. Fuel cells show up as a viable alternative due mainly to two reasons, their high efficiency and the use of renewable fuels. In the present work we study the influence of operating temperature and alkali content in the fuel on the power density for a direct glycerol fuel cell. A glycerol:KOH (1M: xM, x = 0, 1, 3, 5) solution was used as fuels, as membranes were used polibencimidazol films impregnated with phosphoric acid (PBI/H3PO4, molar ratio of 1:11) or 1-hexyl-3-methylimidazolium trifluoromethanesulfonate (PBI/HMI-Tf), and finally, Pt nanoparticles supported on carbon (60% w / w) as catalyst in the anode and cathode. In general, increasing the temperature and alkali content in the fuel shows a favorable effect in the system power density. In a direct glycerol fuel cell using PBI/H3PO4 and PBI /HMI-Tf membranes were obtained power density of 0.54mW.cm-2 at 175°C and 0.599mW.cm-2 at 130°C, respectively, for a 1M glycerol solution; while for a glycerol solution with a higher content of alkali, glycerol:KOH (1M: 5M), were obtained higher power densities, 44.1mW.cm-2 at 175 ° C and 29mW.cm-2 at 130 ° C, respectively. The combined effect of increased temperature and alkali concentration in the fuel shows a greater effect compared to the effect of temperature only.

No description available.