1 |
Elwood Haynes, scientist with a social conscienceHarshbarger, Mary E. January 1965 (has links)
There is no abstract available for this dissertation.
|
2 |
Evaluation of fatigue behaviour of laser beam welded aerospace superalloy haynes 282Buckson, Richard 16 January 2015 (has links)
In 2005, a new, wrought, nickel-base superalloy Haynes 282 was developed. Characteristic of superalloys, Haynes 282 was produced to be used for components, specifically aero and land-based gas turbine engines, which are subjected to high temperatures. The manufacture and/or repair of aero and land-based gas turbine engines require the use of joining processes, an example being welding. However, it was observed that laser beam welding (LBW) of the new superalloy resulted in cracking in the heat affected zone (HAZ) of the alloy. Accordingly, an aspect of this research involves the development of a procedure for preventing or minimizing cracking of the alloy. This is achieved through microstructural modification of the alloy prior to welding through the use of appropriate heat treatment. However, at the core of this research is the main objective of methodically studying the effect of LBW on the high temperature fatigue crack growth (FCG) behaviour of Haynes 282, and how to mitigate any negative effects. Findings from this research show that LBW causes a deleterious effect on the FCG behaviour by increasing the FCG rate. Thus, although this research resulted in a procedure that minimizes cracking during welding of the new alloy, the minimized level of cracking is not tolerable under dynamic loading. Therefore, a procedure to make the minimized level of cracking tolerable during dynamic service is developed. This is achieved by developing two post weld heat treatments, including a new thermal treatment schedule developed in this work, which significantly improved the FCG resistance of the new alloy after LBW. Additionally, Low cycle fatigue (LCF) tests results indicate strong fatigue deformation resistance of Haynes 282. On the other hand, FCG tests results show that, in contrast to common assumption, the loading frequency was observed to have an effect on the FCG behaviour at room temperature. Prior to this research, there was limited publication on the fatigue behaviour of Haynes 282. Hence, the study of the cyclic deformation characteristics and growth behaviour of fatigue crack in Haynes 282 in this research provides valuable information that helps establish design criteria to safeguard against component failure by fatigue.
|
3 |
Comparison of Joining Processes for Haynes 230 nickel Based Super AlloyWilliston, David Hugh 17 August 2013 (has links)
Haynes 230 is a nickel based, solid-solution strengthened alloy that is used for high-temperature applications in the aero-engine and power generation industries. The alloy composition is balanced to avoid precipitation of undesirable topologically closedpacked (TCP) intermetallic phases, such as Sigma, Mu, or Laves-type, that are detrimental to mechanical and corrosion properties. This material is currently being used for the NASA's J2X upper stage rocket nozzle extension. Current fabrication procedures use fusion welding processes to join blanks that are subsequently formed. Cracks have been noted to occur in the fusion welded region during the forming operations. Use of solid state joining processes, such as friction stir welding are being proposed to eliminate the fusion weld cracks. Of interest is a modified friction stir welding process called thermal stir welding. Three welding process: Gas Metal Arc Welding (GMAW), Electron Beam Welding (EBW), and Thermal Stir Welding (TSWing) are compared in this study.
|
4 |
Shear spinning of nickelbased super alloys and stainless steelHiuhu, John January 2015 (has links)
Shear spinning of Haynes 282, Alloy 718, Alloy 600 and AISI 316L was done using several tool feeds and mandrel clearances. Multi passing of the materials was limited due to strain hardening and circumferential cracking except for AISI 316L. The effect of the tool feed and the mandrel clearance on the successful forming of the materials was established. The successfully spun samples were solution heat treated at varying temperatures and holding times to establish a range of grain sizes and hardness levels. An aging heat treatment process was performed for Haynes 282 and Alloy 718 to achieve precipitation strengthening. The micro hardness measurements were conducted for the materials prior to spinning and after spinning. The same was also done after the various heat treatment processes. Grain size mapping was conducted by the use of lineal intercept methods. Comparison of the results in terms of grain sizes and hardness values was done. The temperature ranges suitable for full recrystallization of the materials after the shear spinning were identified and the effect of the holding times on the grain growth established. Comparison with unspun samples showed that the heat treatment times required to achieve comparative hardness and grain sizes were distinctively different.
|
5 |
Design of Experiment for Laser cutting in Superalloy Haynes 282Rådberg, Malin January 2016 (has links)
This project aims to investigate the effect of varying different laser cutting parameters on the laser cut surface. The parameters that were varied were cutting speed, beam effect, gas pressure and focal point. The statistical method Design of Experiment was used to plan the experiments and two full factorial test plans were set up, one with argon as cooling and protective gas and one with nitrogen. Sheet metal consisting of the superalloy HAYNES ® 282 with a thickness of 2,54 mm was investigated. Samples from the material were cut with different laser cutting parameters according to the test plans. The samples were evaluated by measuring cracks, recast layer thickness, surface irregularity, burr height and distance to beam deflection point on the cut surface. The resulting data was inserted as responses into the statistical program Modde 10.1 for analysis. Modde 10.1 provided models of high significance for the responses of Recast layer, Tav; Recast layer, Tmax; Burrheight, max and Distance to deflection point for the argon series and Recast layer, Tav and Recast layer, Tmax for the nitrogen series. The results showed that both recast layer thickness and burr height decreases with increased values of cutting speed, gas pressure and focal point as well as decreased values of beam effect within the parameter window investigated. They also showed that distance to deflection point increased with increasing values of gas pressure and focal point and with decreased values of cutting speed and beam effect within the parameter window. The results also showed that for the samples cut with argon as cooling and assistant gas the parameters that affects the recast layer thickness the most are focal point and gas pressure, whereas for the nitrogen series it is gas pressure and beam effect. The parameter with greatest effect on burr height is the cutting speed and for the distance to deflection point it is focal point and gas pressure that have the greatest effect. When comparing the argon and the nitrogen series to each other it can be seen that the argon series generate less recast layer from the entry of the cut until between 60 – 80 % into the cut, after which the argon series bypasses the nitrogen series in amount of recast layer produced in the cutting process in the majority of the places measured. / Projektet syftar till att undersöka effekten på den laserskurna ytan då laserskärningsparametrar varieras. Parametrarna som varierades var skärhastighet, lasereffekt, gastryck och fokalpunkt. Den statistiska metoden Design of Experiments användes för att planera experimenten. Två stycken fullskaligt faktoriella försöksplaner skapades, en med argon som skärgas och en med kväve som skärgas. Undersökningen gjordes på plåt bestående av superlegeringen HAYNES ® 282 med en tjocklek på 2,54 mm. Provbitar från materialet skars ut utifrån försöksplanerna med olika laserinställningar under skärprocessen. Provbitarna utvärderades genom att mäta sprickor, tjockleken på det omsmälta materialet, ytojämnheten, gradhöjden och avståndet till laserstrålens avböjningspunkt på den laserskurna ytan. Resultaten användes för analys i det statistiska programmet Modde 10.1. Modde 10.1 bidrog med modeller av hög signifikans för responserna Recast layer, Tav; Recast layer, Tmax; Burrheight, max and Distance to deflection point för argonserien och Recast layer, Tav och Recast layer, Tmax för kväveserien. Resultaten visar att både tjockleken på omsmält material och gradhöjden avtar med ökande värden på skärhastighet, gastryck och fokalpunkt samt minskande värden på lasereffekt inom det undersökta parameterfönstret. De visade också att till laserstrålens avböjningspunkt på den laserskurna ytan ökade med ökande värden på gastryck och fokalpunkt och med minskande värden på skärhastighet och lasereffekt inom parameterfönstret. Resultaten visade också att de parametrar som i störst utsträckning påverkar tjockleken på det omsmälta materialet för provbitarna i argonserien är fokalpunkt och gastryck, medan det för kväveserien är gastryck och lasereffekt. Parametern som har högst inverkar på gradhöjden är skärhastigheten, medan fokalpunkt och gastryck har störst effekt på avståndet till laserstrålens avböjningspunkt på den laserskurna ytan. Om kväveserien och argonserien jämförs med varandra kan det observeras att argonserien generellt genererar mindre omsmält material än kväveserien från det att laserstrålen träder in i materialet till dess att den är mellan 60 och 80 % in i snittet, vartefter argonserien går förbi kväveserien i mängd omsmält material på majoriteten av mätställen.
|
6 |
A Quantitative Study of the Weldability of Inconel 718 Using Gleeble and Varestraint Test MethodsQuigley, Sean 01 September 2011 (has links) (PDF)
Nickel super alloy Inconel 718 was tested and compared to Haynes 230 using Gleeble and Varestraint mechanical test methods. Hot cracking susceptibility was examined in either alloy using a sub-scale Varestraint test method at 5 augmented strain levels: 0.25%, 05.%, 1%, 2%, and 4%. Maximum crack length, total crack length, and number of cracks were measured for each strain level. Gleeble hot ductility on-heating and on-cooling tests were performed on both alloys. Inconel 718 was tested on-heating at target temperatures of 1600˚F, 2000˚F, 2100˚F, 2200˚F, and on cooling at 1600˚F, 1700˚F, 1800˚F, 1900˚F, and 2100˚F. Haynes 230 was tested on-heating at target temperatures of 2050 ˚F, 2200 ˚F, 2240 ˚F, 2330 ˚F, and on-cooling at 1800 ˚F, 1900 ˚F, 1990 ˚F, 2040 ˚F, 2090 ˚F, 2100 ˚F, 2140 ˚F, and 2190 ˚F. Ductility in Gleeble samples was measured in a reduction of surface area. A nil-strength temperature was established for either alloy. The nil-strength temperature was 2251˚F and 2411˚F, for Inconel 718 and Haynes 230, respectively. The nil ductility temperature <5% R/A) was 2188˚F for Inconel 718 and 2341˚F for Haynes 230. Ductility recovery temperature occurred at 1924˚F for Inconel 718 and 2147˚F for Haynes 230. The brittle temperature range was determined to be 326˚F for Inconel 718 and 228˚F for Haynes 230. Varestraint testing revealed that Inconel 718 had a lower threshold strain for crack initiation than Haynes 230 (0.5% vs 1%), and a higher number of cracks, as well as a larger maximum crack length, at every strain level. These results show a greater tendency for liquation cracks to form in Inconel 718 than in Haynes 230.
|
7 |
Friction Stir Processing of Nickel-base AlloysRodelas, Jeffrey M. 13 August 2012 (has links)
No description available.
|
8 |
Process understanding of Laser Powder Bed Fusion of Nickel based superalloy Haynes 282 / Processförståelse för laserpulverbäddsfusion av nickelbaserade superlegeringen Haynes 282Swaminathan, Kameshwaran January 2024 (has links)
Laser-material interaction of Nickel based superalloy Haynes 282 melt pools were studied for laser parameters similar to laser powder bed fusion (PBF-LB) without powder. The effect of power, speed, hatch distance and laser focus offset were analysed by characterizing different types of melt pool behaviour, including conduction, transition to keyhole, and keyhole mode. Focus offset parameter was found to modify the melting mode from keyhole to conduction type in experiments with and without powder. This change in melting mode is attributed to the variation in laser beam spot size for the same line energy. Such manipulation of type of melting with control of focus offset can be utilized as a method to optimize process parameters for novel materials in the PBF-LB process at high layer thickness. Based on the above study, cubes were built with refined process parameters utilizing powder layer thicknesses of 60- and 90-microns for improved productivity, using partial factorial design of experiment. The conduction mode of melting helped reducing defects, minimizing lack of fusion and keyhole porosity in specimens built with powder at 60- and 90-microns layer thickness. Effect of process parameters and indirect measure like area energy, on the melt pool overlap, defect level and dominant shape of the defects are presented. Optimizing the process parameters to identify the boundaries for building cubes with reduced porosity is also discussed. / Den Ni-baserade superlegeringen, Haynes 282, skannades med laserparametrar liknande de som används i laserpulverbäddfusion (PBF-LB), men utan pulver.Studien undersökte inverkan av effekt, hastighet, avstånd mellan två intilliggandeskanningspass och laserfokusförskjutning, vilket karakteriserades genom olikatyper av beteenden hos smältbadet, inklusive värmeledning, övergång frånvärmeledning till nyckelhål, och nyckelhål. Fokusförskjutningen visade sig ändrasmältbadets läge från nyckelhål till värmeledning. Denna förändring observeradesbåde i experiment utan pulver och i de med pulver. Förändringen beror påbreddningen av laserstrålens punktstorlek samtidigt som samma linjeenergibibehålls. Denna förändring i smältningstyp genom fokusförskjutning kananvändas som en metod för att optimera utforskningen av nya material i PBFLB-processen. Baserat på detta byggdes kuber med pulver med lagertjocklekar på 60 och 90mikrometer, användande olika processparametrar enligt en experimentell designbaserad på en central sammansatt design. Smältning genom värmeledning bidrogtill att minska defekter, minimera bindningsfel och nyckelhålsporositet i proversom byggts med pulver med lagertjocklekar på 60 och 90 mikrometer. Inverkanav processparametrarna och indirekta mått såsom areaenergi på smältbadetsöverlappning, defektnivå och den dominerande formen på defekter presenteras.Optimering av processparametrarna samt identifiering av parameterrymden föratt bygga kuber med minskad porositet undersöks också. / <p>Paper A is to be submitted, and paper C is acceptet and are not included in this licentiate thesis. We do not have permission to publish paper B in the digital version.</p>
|
9 |
“Mere Supplicants at the Gate”: Northeast Tennessee Politics in the Antebellum EraEarly, O.J. 01 May 2016 (has links)
Antebellum political historians have long studied the era between Andrew Jackson’s election and the secession crisis through the colored knowledge of the Civil War. This project is an effort to reverse that trend. It explores northeast Tennessee’s political culture from the late 1830s through the start of the Civil War. It reveals that the Second American Party System, a wave of new enfranchised voters, and the area’s demographics mixed together to lay a foundation for the aggressive and populist political style that permeated the region from the 1830s through the 1850s. At the heart of these issues was the transition of power from East Tennessee to Middle Tennessee. As a way to analyze the region’s political culture, I look specifically at Democrats Andrew Johnson and Landon Carter Haynes and Whigs William Brownlow and Thomas Nelson.
|
10 |
MÉCANISMES DE FORMATION ET DE DESTRUCTION DE LA COUCHE D'OXYDE SUR UN ALLIAGE CHROMINOFORMEUR EN MILIEU HTRRouillard, Fabien 19 October 2007 (has links) (PDF)
Le superalliage à 22%mas. en chrome, Haynes 230®, est un matériau candidat pour les échangeurs de chaleur (température maximale 850°C-950°C) des Réacteurs à Caloporteur Gaz, également appelés HTRs (High Temperature Reactors). Dans l'optique de valider les performances de cet alliage, il faut garantir sa résistance à la corrosion dans l'environnement d'hélium impur de ces réacteurs. Dans cet objectif, la réactivité de surface de l'Haynes 230® a été examinée à des températures comprises entre 850 et 1000°C. On s'est attaché à caractériser l'influence de différents paramètres tels que concentrations en impuretés du gaz (monoxyde de carbone, méthane et rapport vapeur d'eau/dihydrogène), caractéristiques de l'alliage (activités en Cr et en C, teneurs en éléments mineurs) et température d'exposition. Deux principaux comportements ont pu être mis en évidence : la formation d'une couche d'oxyde riche en Cr et Mn à 900°C et sa réduction à plus hautes températures. A 900°C, la vapeur d'eau est l'oxydant principal. Toutefois dans les temps initiaux, le monoxyde de carbone réagit à l'interface métal/oxyde ce qui implique un transport de gaz au travers de la couche ; CO semble préférentiellement oxyder les éléments mineurs aluminium et silicium. A partir d'une température critique TA, le carbone en solution dans l'alliage réduit l'oxyde de chrome. Un modèle de destruction de la couche basé sur les grandeurs thermodynamiques interfaciales de l'alliage, la morphologie de la couche et la pression partielle en monoxyde de carbone dans l'hélium est proposé puis validé.
|
Page generated in 0.0439 seconds