Efficiency of a ground source heat pump with thermal capacity of 6 kW determined in two differentlocations in Sweden. In the north side with low average temperature which could go down to -10 ᵒCand in the south side, with low average temperature with +2 ᵒC. The heat pump has refrigerantR407c, which could be connected to both, ground source heat feeding methods the horizontal, andthe vertical model. The heat pump give heat for both space heating and domestic hot watercompared the micro CHP which has thermal capacity of 12.5 kW and electrical capacity of 4.4 kW. Ithas IC engine which means the engine has internal combustion work. It also works with two kinds offuel, natural gas and propane MOZ 92; the energy and exergy of the fuel in micro CHP feeding thethermal process by heat. That heat used for space heating and domestic hot water after going outthe process for the cooling which keep the heat in storage tank and it heat the liquid to the gas to beused in the turbine to produce the electricity. The two locations in the north and south of Swedenwill influence the thermal operation and that influence power used for compressor for heat pumpand somehow the pump in the micro CHP. The study shows that the different in exergy and energyefficiency between these two heat technologies by located them in the locations. Higher efficiencyof the micro CHP which give the advantage of use Micro CHP some technology give the benefit byusing the fuel for producing the heating and electricity , the benefit which give the customer manybenefit shows in the study. That’s comparing with the heat pump which is large use in Sweden. Inthis paper will introduce Micro CHP as heating technology which has been used in the rest of Europecould be used in Sweden for future heating technology with electricity producing, shall change thecostumer from energy consumption costumer to producing costumer.

The beachfront hotel with hybrid geothermal heat pump system (HyGSHP), located in the hot-humid climate, is simulated by TRNSYS in the thesis, and the simulation results are validated by the measured data. The simulation of alternative HVAC systems, complete ground source heat pump and conventional air source heat pump, are included to conduct the comparative study with HyGSHP based on the energy consumption and life cycle analysis. The advantages and disadvantages of HyGSHP are discussed in the thesis. Two ground source heat exchanger parameters, U-tube size and grout materials, are investigated in order to study the effects on the ground heat exchanger thermal performance. The preliminary work and results are shown in the thesis.

This master thesis describes the issue of the measuring and control system for the heat pump. In the first part of the thesis is described the principle of heat pump activity, its basic components. The second part contains the distribution of heat pumps according to the method of obtaining and transferring the heat. The following chapter contains the description of system status before the modernization. In the practical part of this thesis is the proposal and realization of new control and monitoring system including the description of individual components. In the conclusion of the thesis is a verification of the use of proposed control and monitoring system of heat pump for the measuring of its operational characteristics.

Diploma thesis focuses on creation of scheduling system for production processes and labour within heat pump manufacturing line in Daikin Device Czech Republic, connected with modification of production and warehouse layout. First part analyzes products, assembly line and its current state of layout. Furthermore it deals with measurement and analysis of work performed by operatives. Proposal part describes layout changes, whereupon line balancing is processed for different production levels and finally comes creation of scheduling system itself.

Geothermal heat exchangers are a growing energy technology that improve the energy efficiency of heating and cooling systems in buildings. Vertical borehole heat exchangers (BHE) coupled with ground source heat pumps have been widely developed and researched in the past century. The major disadvantage of BHEs is the initial capital cost required to drill the boreholes. Geothermal energy piles (GEP) were developed to help offset the high initial cost of these systems. A GEP combines ground source heat pump technology with deep earth structural foundations of buildings. GEPs are relatively new technology and robust standards and guidelines have not yet been developed for the design of these systems. The main operational difference between GEPs and conventional BHEs is the length and diameter of the below ground heat exchangers. The diameter of a GEP is much larger and the length is typically shorter than BHEs. Computational fluid dynamics (CFD) analysis is used in this study to investigate and better understand how structural piles perform as geothermal heat exchangers. The CFD analysis is used to simulate an existing experimental energy pile test. The experimental test is modeled as built including fluid modeling to provide additional detail into the behavior of the circulation fluid within the pile. Two comparisons of large diameter GEPs are made using CFD analysis to gain knowledge of the effects of varying pile diameter and loop configuration. The thermal response test was successfully modeled using the CFD model. The CFD results closely match the results of the field test. The large diameter comparisons show that the performance of an energy pile will increase as the diameter increases with a constant loop density. Multiple numbers of loops were tested in a constant diameter pile and the results show that with symmetrically placed loops the performance will increase with a greater number of loops in the pile. / Master of Science

Experiments were carried out to investigate the effect of ambient air temperatures on the heat pump performance using a variable speed compressor. Ambient air temperatures were varied from 40 to 60 °F to simulate different seasons. The compressor frequencies of 45 Hz, 50 Hz, 55 Hz, and 60 Hz were studied to determine the optimal frequency under various heating loads. The investigation was carried out by showing the compressor power input, heating output, and coefficient of performance for each case. Thermal cycle analysis along with the heat exchanger theory was used to analyze the system energy balance, heat transfer rates, p-h diagrams, and coefficient of performance. The overall heat transfer coefficients were also determined for both the evaporator and the condenser. Only the capillary tube was used to regulate the refrigerant flow rate. The variable speed compressor system used in this study will help save energy when compared with the traditional steady speed system. The variable speed compressor system will hopefully provide a more comfortable and steady indoor temperature than the traditional system, which is controlled by only an on-off switch. The speed controlled compressor system proposed we believe will help saving more energy than traditional steady speed system. The variable speed compressor system will hopefully provide a more comfort and steady indoor temperature than the traditional system which is controlled by one switch. It is believed that the variable speed compressor system may allow the indoor temperature air to be steady-going and prevent the switch working frequently. / Mechanical Engineering

Mr Wayne Tobeck, Director of Southrim Group (SRG), sponsored this 2013 MEM Project titled; A Technical and Economic Feasibility Study for the Integration of GSHP Technology in the Christchurch Rebuild. Following the recent Christchurch earthquakes, a significant amount of land has become too unstable to support traditional building foundations. This creates an opportunity to implement new and unique foundation designs previously unconsidered due to high costs compared to traditional methods. One such design proposes that an Injection Micro-Piling technique could be used. This can also be coupled with HVAC technology to create a Ground Source Heat Pump (GSHP) arrangement in both new buildings and as retrofits for building requiring foundation repair. The purpose of this study was to complete a feasibility study on the merits of SRG pursuing this proposed product. A significant market for such a product was found to exist, while the product was also found to be technically and legally feasible. However, the proposed product was found to not be economically feasible with respect to Air Source Heat Pumps due to the significantly higher capital and installation costs required. Further analysis suggests GSHPs may become more economically attractive in operating temperatures lower than -9oC, though the existence of markets with this climate in NZ has not been studied. It is therefore suggested that SRG do not proceed with plans to develop a GSHP coupled foundation solution for the Christchurch rebuild.

Parametric performance analyses and comparison of a basic geothermal heat pump, a heat pump cycle with motor cooling/refrigerant preheating, and a heat pump cycle utilizing an economizer with respect to first law is conducted through simulation. Changing compressor, pump, and motor efficiency, along with condenser pressure, evaporator pressure, degree of subcooling at the condenser exit and degree of superheating at the evaporator exit is investigated. Economizer arrangements yield the highest coefficient of performance and resilience to change in COP with variation in evaporator pressure, and degree of superheating and subcooling. The basic vapor compression and motor cooling/refrigerant preheating systems have the lowest COP throughout and greatest resilience to variation in compressor efficiency, motor efficiency and condenser pressure. Motor cooling/refrigerant preheating and economizers have advantages over basic vapor compression cycles. Motor cooling reduces ground loop heat exchanger length with similar COP, and economizers allow for an increase in COP compared to the basic cycle. / UOIT

Due to rising energy costs and increasing environmental awareness, various methods of energy conservation are being investigated. In the residential sector, both solar and heat pump systems have been extensively tested. Recently, combinations of solar and heat pump systems have been developed for both space heating and water heating. These systems have the capability to provide better performances than either of the systems operating on their own. The solar collector benefits from a lower fluid (glycol) inlet temperature which increases efficiencies, and the heat pump benefits from higher evaporator temperatures due to the additional solar energy collected. For this study, a prototype of an Indirect-Solar Assisted Heat Pump for use in the Canadian environment was constructed, instrumented and tested. Controlled, constant temperature tests, as well as solar profile tests were conducted and the heat transfer rates, natural convection flow rate, and heat pump coefficient of performance (COP) were calculated. These values were then compared to simulation results based on a model developed in a previous feasibility study. The experimental COPs calculated ranged from 2.3 to 3.3 throughout the full range of tests which were conducted with supply temperatures ranging from 0°C – 40°C. The simulated results consistently overestimated the experimental results by between 12% - 15%. New empirical heat exchanger relationships were developed for the model bringing the simulated results within 5% of the experimental results for tests run at glycol flow rates of 77 and 154 kg/hr. These relationships were used to refine the model, and produce updated annual performance values in the TRNSYS simulation software. Updated results showed a 5% drop in the annual free energy ratio in Toronto from 57% to 52%, but further optimization of the system using the TRNSYS software package improved annual results up to 56%. For the purposes of the study, a solar assisted heat pump prototype was constructed and tested successfully within the laboratory environment. Results showed that the system has a strong market potential, especially in regions without a strong solar resource. Based on these results further research is recommended, continuing with a full year outdoor test using unglazed solar collectors. / Thesis (Master, Mechanical and Materials Engineering) -- Queen's University, 2010-10-12 18:53:01.189

Lågtempererade värmekällor som ytvatten och borrhålslager kan i samverkan med en värmepump ses som outnyttjade energikällor. En sjö- och borrhålsbaserad anläggning kan ha en hög total effektivitet om både värme och kylbehov finns och en stor fördel är att frikyla kan användas från sjö och borrhål under delar av året. Kungsbrohuset byggdes 2008 - 2010 med målsättningen att bli världens mest energieffektiva kontorsbyggnad. Mer specifikt var målsättningen att köpt energi skulle vara hälften av boverkets regler. Av den totala bruksarean på 27 000 m2 utgörs ca 19 500 m2 av kontorsyta. Anläggningen värms och kyls huvudsakligen av en värmepump med en värmeeffekt på 350 kW. Vintertid används värmepumpen för både värme och kyla då ett stort kylbehov även finns under uppvärmningssäsongen till serverrum mm. När värmepumpen inte räcker till så används fjärrvärme och fjärrkyla/sjökyla för att täcka behovet. Vid byggnationen installerades en ledning mellan kungsbrohuset och centralstationen för att på centralstationen utnyttja frikyla från sjön samtidigt som kungsbrohuset fick möjligheten att utnyttja värmen i köldbärarreturen. Målet med studien var att utvärdera anläggningen med fokus på tre huvudsakliga frågor. Att undersöka om värmepumpen har högsta möjliga temperatur på förångningssidan vintertid var den första. Den andra frågan var om frikyla från sjön utnyttjades optimalt. Den tredje frågan var att jämföra den projekterade energianvändningen med det verkliga utfallet. Studien utfördes genom besiktningar på plats, insamling av energistatistik samt att studera anläggningen genom driftdator, driftkort, flödesscheman etc. Vintertid så har den egna köldbärarreturen använts nästan uteslutande som värmekälla till värmepumpen då dess temperatur är högre än borrhålslagrets. Utnyttjandet av frikyla från sjön har inte fungerat optimalt då fjärrkyla har använts under vintermånaderna trots att sjöns temperatur är låg. Detta kan åtgärdas genom omprogrammering av villkor för aktivering av frikylan. Jämförelsen mellan projekterad köpt fastighetsenergi på 47 kWh/m2, år med det verkliga utfallet visade att användningen är något högre i verkligheten och hamnade på 55 kWh/m2, år efter att processkylan räknats bort då den inte räknas som fastighetsenergi. Anläggningen är totalt sett väldigt effektiv och har en mycket låg användning av köpt energi. Att kylbehov finns även vintertid gör att värmepumpens effektivitet blir maximal då nyttig energi utnyttjas på båda sidorna.