Sub-surface soil pollution by various processes with high concentration of contaminants can significantly alter geotechnical properties of soils causing unexpected failures of structures founded on them. The changes can occur due to alteration in soil water interaction processes and/or by intense chemical interactions leading to mineralogical and microstructural changes. Behaviour of soil upon contamination with alkali pollutant is one of the major concerns faced by the geotechnical researchers in recent years. In the present study an attempt has been made to understand the role of mineralogical and morphological changes on the volume change (swelling and compressibility) behaviour of soils by prolonged interaction with caustic alkali pollutant. Based on the results it has been proposed to develop remedial measures to nullify and/or control the detrimental effects. A comprehensive experimental program has been planned to achieve these objectives. The experimental investigations carried out and results obtained are presented in eight chapters as follows. The broad outline of thesis is given in Chapter 1. A detailed review of literature on the type of phyllosilicate minerals present in various soils is presented in Chapter 2 with a view to select most common soils for the study. Various sources of contaminants and their effect on the properties of soils have been summarised. Present understanding on the mechanisms leading to changes in the soil properties has been elucidated. The occurrence of alkali contamination has been reviewed in this chapter which enabled to select the ranges of alkali concentration for the study. Based on the review of various methods employed to improve the soil behaviour, the use of salt solutions such as potassium chloride (KCl) and magnesium chloride (MgClB2B) and pozzolanic fly ash has been considered to counteract the alkali effects. Based on this detailed survey, the scope of the present investigation has been elaborated at the end of the chapter. Chapter 3 presents different materials used and various methods adapted in the current study. Three soils having different mineralogy have been used in this study to bring out the effect of alkali solutions on their volume change behaviour. While two soils were classified as CH, the third one was of CL. The CH soils used in this study are called Black Cotton Soils in India. One soil contained predominantly mixed layer illite-smectite mineral (BCS I) and the other contained predominantly montmorillonite mineral (BCS M). The locally available CL soil used is referred as red earth (RE) whose predominant mineral is kaolinite. Alkali solutions of concentration ranging from 1N to 4N are prepared using sodium hydroxide pellets (NaOH). Slat solutions viz. potassium chloride and magnesium chloride and pozzolanic fly ash obtained from Neyveli thermal power plant (NFA) are used as additives. Procedures to determine the geotechnical properties of the soils such as Atterberg limits, specific gravity, grain size distribution and compaction characteristics are given in this chapter. Procedures for identifying the mineral and microstructure of the soils such as X-ray diffraction (XRD) and scanning electron microscopy (SEM) are also presented in this chapter. Standard oedometer tests with fixed ring apparatus were performed to study the volume change behaviour of soils under various conditions. Volume change behaviour of soils in the presence of alkali solutions is presented in Chapter 4. In order to assess the effect of alkali solution on the volume change behaviour of soils it is necessary to study their behaviour in water. Relatively very high swell was observed in BCS M, whereas the swell in RE and BCS I soil specimens was very low and moderate respectively. Adsorption of water to form diffuse double layer near the negative surface of clay mineral particles leads to swelling in soils. The thickness of the double layer depends on the cation exchange capacity of soil. Higher cation exchange capacity leads to development of higher thickness of double layer thereby inducing swell. The higher is the swell the higher would be the compression. The effect of different concentrations (1N, 2N and 4N) of alkali solutions on volume change behaviour of three types of soil is presented in this chapter. All the three soils studied, irrespective of their mineralogical composition, exhibited high swell when contaminated with alkali solution compared to water. However, the extent and nature of swell varied both with the type of mineral present in the soil and concentration of sodium hydroxide solution. The swell in BCS I increases with increase in the concentration of the alkali solution. In 1N alkali solution the high swell occurred is due to the breaking up of interstratified mineral into constituent minerals initiated by the leaching of potassium from soil due to high pH. In 2N and 4N alkali solutions, the observed high swell occurs in two stages: the first stage of swelling is due to breaking up of interstratified mineral into constituent minerals initiated by the leaching of potassium from soil due to high pH, and the second stage of swelling is due to the formation of new minerals (Zeolite P in case of 2N NaOH and Sodalite in case of 4N NaOH). The nature of swell is influenced by the formation of minerals depending on the concentration of alkali solution. Thus the studies clearly indicate that the swelling is due to the release of potassium from soil at higher pH and due to mineralogical changes depending upon the concentration of alkali solution. Confirmative tests were conducted to support the release of potassium during first stage of swelling and mineralogical alteration after second stage of swelling. The high swell in BCS M becomes higher in 1N alkali solution. The increased swell in the soil with 1N alkali solution is due to increase in the ion exchange capacity of soil at higher pH. The swell which is very high with 1N alkali solution decreases with 2N alkali solution. With increase in concentration of alkali solution to 2N, the increase in the negative charges due to alkalinity becomes less and the swell decreases due to dominant influence of electrolyte effect. With increase in the concentration of alkali solution to 4N, both these influences become less and the amount of swell remains the same. Significant increase in the amount of swell is observed with alkali solution even in non-swelling red earth. The nature of swell as well as the formation of minerals is not altered by the change in the concentration of alkali solution. At any concentrations of alkali solution the observed swell is noticed in two stages – very small first stage of swell due to lower ion exchange capacity and considerable second stage of swell due to the formation of new mineral (Sodalite) with any concentration of alkali solution. It has been observed that the normal hyperbolic swell – compression relationship does not apply for the alkali contaminated soils. The higher swell does not result in higher compression, as the swollen soil remains fairly incompressible. Analysis of the results and detailed studies on micro-structure and mineralogy of soils bring out mechanism of alkali effects. Comparing the swell behaviour of soils with alkali solutions brings out the relative importance of various mechanisms proposed for induced heave. The effect of salt solutions used viz., potassium chloride and magnesium chloride to restrict the influence of alkali solution on the volume change behaviour of BCS I is presented in Chapter 5. These salts react with alkali solution to form partly soluble potassium hydroxide (KOH) and sparingly soluble magnesium hydroxide (Mg(OH)B2B) respectively. Presence of ionic potassium can bring out potassium linkages, by bridging potassium ion between the unit layers of expansive minerals reducing the swell. Magnesium ions can restrict swell, by replacing the monovalent exchangeable ions present in soil and/or by formation of magnesium hydroxide which is a weak cementing agent. The effect of potassium hydroxide on the volume change behaviour of soil has been studied and the results clearly indicate that fixation of potassium is facilitated by high pH of KOH solution. Addition of potassium chloride has partially controlled the alkali induced heave in soil. Of the two stages of swelling observed in soil in the presence of 4N alkali solution, only the first phase of swelling is reduced which may be due to electrolyte effect and/or due to fixation of potassium. The second phase of swelling that occurs in soil due to mineralogical changes can not be controlled with the use of potassium chloride. Addition of magnesium chloride salt solution also reduced the effect of alkali solution mostly due to suppression of thickness of diffuse double layer that develops near clay surface. The nature of reduction in the swell of alkali solution during the two stages by magnesium chloride is similar to that of potassium chloride. The partial reduction in swell of soil in the presence of salt solutions leads to reduction in the compressibility of soil. Detailed data and analysis, presented in this chapter, bring out the role of microstructure and mineralogy on soil behaviour. The abnormal volume changes due to mineralogical changes affected by high concentration of sodium hydroxide could not be controlled with salt solutions, attempts are made to utilize fly ash to control the alkali induced heave. The pozzolanic compounds produced by hydration of compounds presented and/or produced by lime silica reactions can bind the soil particles controlling the swelling. The results on the effectiveness of fly ash on BCS I soil are presented in Chapter 6. The physical and chemical properties of fly ash along with the mineralogical composition and the microstructure of the fly ash are also presented in this chapter. Before studying the effect of fly ash to control the volume change behaviour of soils in presence of alkali solutions, the effect of alkali solutions on the volume change behaviour of fly ash itself has been studied. The results showed no noticeable changes in swell and compressibility of fly ash, encouraging its use for controlling the alkali induced swell. The ability of different percentages (10%, 20% and 50%) of fly ash to control alkali induced volume changes in soil with varying concentrations of alkali solutions, viz., 1N, 2N and 4N has been studied. The results indicate that the addition of fly ash effectively reduces alkali induced swell in BCS I. The effectiveness of fly ash increases with increase in its content. The reduction in swelling of soil is partially due to replacement of soil with fly ash and mainly due to cementation of soil particles by pozzolanic compounds produced. More than 25% of fly ash is generally required to significantly reduce the swell in alkali solutions. The reduction in swell with addition of fly ash also leads to lower compressibility of soil. The role of microstructure and mineralogy in controlling the volume change behaviour are also presented in this chapter. The effectiveness of fly ash in controlling the volume changes in RE and BCS M due to alkali solutions are studied in Chapter 7. The addition of fly ash completely eliminates the swelling in both the soils. The reduction in swelling up on addition of fly ash is essentially due to efficient binding of particles by pozzolanic reaction compounds. Addition of even 10% of fly ash is sufficient in completely arresting the swelling of RE and BCS M by alkali solution. Detailed data and analysis of the results to bring out the role of microstructure and mineralogy on the behaviour of soils are presented. It is clear that relatively higher amounts of fly ash is required to control the alkali induced heave in BCS I than in other soils at higher concentrations of alkali solution. The major conclusions from the study are presented in Chapter 8. The thesis demonstrates that alkali contamination alters mineralogy and morphology of soils affecting the volume change behaviour significantly. The study also brings out that fly ash can control the undesirable swell that occurs in most types of soils by cementing the soil particles to resist swelling. Though the amount of fly ash required to control the alkali induced heave varies, 25% of fly ash is often sufficient.

On s'intéresse dans le présent travail au comportement au gel des sols fins limono-argileux traités à la chaux seule, sols valorisables qui sont couramment rencontrés sur les chantiers de terrassement. Trois sols appartenant aux classifications A1, A2, A3 selon la norme NF P 11300, ont été choisis pour cette étude. Ces sols sont traités à 3 dosages en chaux correspondant à 3 objectifs : 1) amélioration (dosage en chaux minimal), 2) stabilisation et insensibilité à l'eau (dosage en chaux intermédiaire), 3) stabilisation et résistance au gel (dosage en chaux le plus élevé). Les sols traités sont ensuite conservés pendant quatre périodes de cure : 7 jours, 28 jours, 90 jours et 365 jours. Les deux processus de gel - le géligonflement et la gélifraction sont étudiés, parallèlement à l'évaluation des performances mécaniques, hydrauliques et microstructurales. Les résultats expérimentaux ont montré que les propriétés hydrauliques (la succion au front de gel, sp et la conductivité hydraulique à l'état non-saturé, kunsat) sont les paramètres qui gouvernent le phénomène de géligonflement des sols, traités ou non. Les résultats ont également mis en évidence le lien direct existant entre la microstructure (la distribution porale) et les propriétés hydrauliques du sol, principalement en termes de capacité de rétention d'eau et conductivité hydraulique. Le traitement augmente les performances mécaniques des sols d'une part, et amène d'autre part à des modifications de leur microstructure ; ceci induit des changements vis-à-vis de leur sensibilité au gel. Les sols sont plus gélifs directement après le traitement, cette sensibilité au gel diminuant avec le temps de cure. Une modélisation simple permettant d'estimer le gonflement au gel à partir de la succion au front de gel et de la valeur de conductivité hydraulique à l'état non-saturé a été proposée et validée. Vu que la détermination de la conductivité hydraulique à l'état non-saturé n'est pas un essai couramment pratiqué au sein de la plupart des laboratoires, un critère basé sur la succion au front de gel, sp, et la conductivité hydraulique à l'état saturé, ksat a été proposé pour évaluer la sensibilité des sols au gel. L'essai de gélifraction consiste à évaluer un coefficient de résistance de l'éprouvette de sol après 10 cycles de gel/dégel, RFT (%) - « retained strength factor after freeze-thaw testing ». Les résultats expérimentaux montrent que la valeur RFT des sols traités varie de 0% (lorsque les éprouvettes de sol perdent totalement leur résistance à la compression simple et sont détruites après 10 cycles de gel/dégel) à 90%. Quand RFT ≥ 60%, aucune dégradation visuelle de la surface des éprouvettes des sols traités n'est constatée. Ainsi, cette valeur est proposée comme critère d'acceptation des matériaux constitutifs d'une couche de forme subissant le gel avant son recouvrement. L'étude de l'effet du nombre des cycles de gel/dégel montre une diminution importante de la performance mécanique (RFT) durant trois premiers cycles de gel/dégel, et ce paramètre se stabilisant après 10 cycles. A l'aide de la technique de µ Tomographie X, l'endommagement interne des éprouvettes de sol ayant subi des cycles de gel/dégel a été quantifié. Une corrélation directe entre la diminution de performance mécanique et l'augmentation de l'indice de l'endommagement de l'éprouvette a été mise en évidence. Enfin, un modèle d'endommagement permettant d'évaluer la dégradation de la performance mécanique avec l'augmentation de l'indice d'endommagement a été établi / The present work deals with the behaviour of fine-grained silty and clayey soils treated with lime under frost. Those soils are frequently encountered in earthworks. Three soils corresponding to A1, A2, A3 classes according French NF P 11-300 standard were chosen for this study. These soils were treated with 3 lime dosages corresponding to three objectives: 1) improvement (minimum dosage), 2) stabilization and insensitivity to water (intermediate dosage), 3) stabilization and frost resistance (highest dosage). Lime-treated soils were subsequently cured for different times: 7, 28, 90, 365 days. Two frost processes, frost heave and freeze-thaw cycles, were applied in parallel with the assessment of mechanical, hydraulic and microstructural properties. Experimental results evidenced that it is the hydraulic properties (suction at frost front, sp and unsaturated hydraulic conductivity, kunsat) that govern the frost heave phenomenon of soils, treated or not. In addition, this study demonstrates the direct link between the microstructure (the pore size distribution) and the hydraulic properties (water retention curve and hydraulic conductivity). The treatment on one hand improves the mechanical performances of soils, and on the other hand modify their microstructure, and thus changes their frost sensitivity. The frost susceptibility increases directly after treatment, and then decreases with curing time. Based on the suction at frost front and the unsaturated hydraulic conductivity, a simple model was proposed and validated allowing to estimate the frost heave. Considering that the determination of unsaturated hydraulic conductivity is not a test commonly performed by most laboratories, a criterion based on the suction at frost front and the saturated hydraulic conductivity was proposed to estimate the frost sensibility of soils. The second frost resistance test consists of measuring the retained strength factor after 10 freeze-thaw cycles, RFT (%). The results obtained show that RFT of lime treated soil varies from 0% (when soil specimen completely loses its resistance and collapses after 10 freezethaw cycles) to 90%. When RFT is higher than 60%, no visual damage was observed on the specimen surface; consequently, this value is proposed as a criterion for acceptance of lime treated soil in capping layer before covering. In addition, the study of effect of freeze-thaw cycles showed a significant decrease of mechanical performance (RFT) during the first three cycles, and a stabilization after 10 cycles. Using X-ray Tomography, the intern damage of specimens due to freeze-thaw cycles was quantified. A correlation between the decrease of mechanical performance and the increase of damage index was evidenced. A model was then developed to evaluate the degradation of mechanical performance with the increase of damage index

On s'intéresse dans le présent travail au comportement au gel des sols fins limono-argileux traités à la chaux seule, sols valorisables qui sont couramment rencontrés sur les chantiers de terrassement. Trois sols appartenant aux classifications A1, A2, A3 selon la norme NF P 11300, ont été choisis pour cette étude. Ces sols sont traités à 3 dosages en chaux correspondant à 3 objectifs : 1) amélioration (dosage en chaux minimal), 2) stabilisation et insensibilité à l'eau (dosage en chaux intermédiaire), 3) stabilisation et résistance au gel (dosage en chaux le plus élevé). Les sols traités sont ensuite conservés pendant quatre périodes de cure : 7 jours, 28 jours, 90 jours et 365 jours. Les deux processus de gel - le géligonflement et la gélifraction sont étudiés, parallèlement à l'évaluation des performances mécaniques, hydrauliques et microstructurales. Les résultats expérimentaux ont montré que les propriétés hydrauliques (la succion au front de gel, sp et la conductivité hydraulique à l'état non-saturé, kunsat) sont les paramètres qui gouvernent le phénomène de géligonflement des sols, traités ou non. Les résultats ont également mis en évidence le lien direct existant entre la microstructure (la distribution porale) et les propriétés hydrauliques du sol, principalement en termes de capacité de rétention d'eau et conductivité hydraulique. Le traitement augmente les performances mécaniques des sols d'une part, et amène d'autre part à des modifications de leur microstructure ; ceci induit des changements vis-à-vis de leur sensibilité au gel. Les sols sont plus gélifs directement après le traitement, cette sensibilité au gel diminuant avec le temps de cure. Une modélisation simple permettant d'estimer le gonflement au gel à partir de la succion au front de gel et de la valeur de conductivité hydraulique à l'état non-saturé a été proposée et validée. Vu que la détermination de la conductivité hydraulique à l'état non-saturé n'est pas un essai couramment pratiqué au sein de la plupart des laboratoires, un critère basé sur la succion au front de gel, sp, et la conductivité hydraulique à l'état saturé, ksat a été proposé pour évaluer la sensibilité des sols au gel. L'essai de gélifraction consiste à évaluer un coefficient de résistance de l'éprouvette de sol après 10 cycles de gel/dégel, RFT (%) - « retained strength factor after freeze-thaw testing ». Les résultats expérimentaux montrent que la valeur RFT des sols traités varie de 0% (lorsque les éprouvettes de sol perdent totalement leur résistance à la compression simple et sont détruites après 10 cycles de gel/dégel) à 90%. Quand RFT ≥ 60%, aucune dégradation visuelle de la surface des éprouvettes des sols traités n'est constatée. Ainsi, cette valeur est proposée comme critère d'acceptation des matériaux constitutifs d'une couche de forme subissant le gel avant son recouvrement. L'étude de l'effet du nombre des cycles de gel/dégel montre une diminution importante de la performance mécanique (RFT) durant trois premiers cycles de gel/dégel, et ce paramètre se stabilisant après 10 cycles. A l'aide de la technique de µ Tomographie X, l'endommagement interne des éprouvettes de sol ayant subi des cycles de gel/dégel a été quantifié. Une corrélation directe entre la diminution de performance mécanique et l'augmentation de l'indice de l'endommagement de l'éprouvette a été mise en évidence. Enfin, un modèle d'endommagement permettant d'évaluer la dégradation de la performance mécanique avec l'augmentation de l'indice d'endommagement a été établi / The present work deals with the behaviour of fine-grained silty and clayey soils treated with lime under frost. Those soils are frequently encountered in earthworks. Three soils corresponding to A1, A2, A3 classes according French NF P 11-300 standard were chosen for this study. These soils were treated with 3 lime dosages corresponding to three objectives: 1) improvement (minimum dosage), 2) stabilization and insensitivity to water (intermediate dosage), 3) stabilization and frost resistance (highest dosage). Lime-treated soils were subsequently cured for different times: 7, 28, 90, 365 days. Two frost processes, frost heave and freeze-thaw cycles, were applied in parallel with the assessment of mechanical, hydraulic and microstructural properties. Experimental results evidenced that it is the hydraulic properties (suction at frost front, sp and unsaturated hydraulic conductivity, kunsat) that govern the frost heave phenomenon of soils, treated or not. In addition, this study demonstrates the direct link between the microstructure (the pore size distribution) and the hydraulic properties (water retention curve and hydraulic conductivity). The treatment on one hand improves the mechanical performances of soils, and on the other hand modify their microstructure, and thus changes their frost sensitivity. The frost susceptibility increases directly after treatment, and then decreases with curing time. Based on the suction at frost front and the unsaturated hydraulic conductivity, a simple model was proposed and validated allowing to estimate the frost heave. Considering that the determination of unsaturated hydraulic conductivity is not a test commonly performed by most laboratories, a criterion based on the suction at frost front and the saturated hydraulic conductivity was proposed to estimate the frost sensibility of soils. The second frost resistance test consists of measuring the retained strength factor after 10 freeze-thaw cycles, RFT (%). The results obtained show that RFT of lime treated soil varies from 0% (when soil specimen completely loses its resistance and collapses after 10 freezethaw cycles) to 90%. When RFT is higher than 60%, no visual damage was observed on the specimen surface; consequently, this value is proposed as a criterion for acceptance of lime treated soil in capping layer before covering. In addition, the study of effect of freeze-thaw cycles showed a significant decrease of mechanical performance (RFT) during the first three cycles, and a stabilization after 10 cycles. Using X-ray Tomography, the intern damage of specimens due to freeze-thaw cycles was quantified. A correlation between the decrease of mechanical performance and the increase of damage index was evidenced. A model was then developed to evaluate the degradation of mechanical performance with the increase of damage index

In the theoretical part of the thesis, different methods of testing frost susceptibility in the Czech Republic and other countries of the European Union are compared. The practical part of the thesis deals with laboratory testing of frost susceptibility of concrete and mixed recycled materials using the direct method of frost heave tests as well as determining the California Bearing Ratio (CBR) and design module of elasticity using the cyclic triaxial test. Suitability of materials for construction of road infrastructure is then assessed on the basis of the results of these tests.

The Portland Cement Association commissioned a research project at Brigham Young University to compare selected laboratory durability tests available for assessing stabilized subgrade materials. Improved understanding of these tests is needed to enable more objective selection of durability tests by design engineers and to facilitate more meaningful comparisons of data obtained for different stabilizer treatments using different evaluation procedures. The laboratory research associated with this project involved two subgrade materials, four stabilizers at three concentrations each, and three durability tests in a full-factorial experimental design. The two subgrade soils used were a silty sand and a lean clay, while the four stabilizer types included Class C fly ash, lime-fly ash, lime, and Type I/II portland cement. The three tests used in this comparative study were the freeze-thaw test, the vacuum saturation test, and the tube suction test. On average, to achieve the same 7-day unconfined compressive strength (UCS) values, the sand required 4.4 times more Class C fly ash than cement, 3.6 times more lime-fly ash than cement, and 6.0 times more lime than cement. Likewise, the clay required 10 times more Class C fly ash than cement, 7.5 times more lime-fly ash than cement, and 1.8 times more lime than cement. Analyses of the test results indicated that the UCS and retained UCS were higher for specimens tested by vacuum saturation than the corresponding values associated with freeze-thaw cycling. This observation suggests that the freeze-thaw test is more severe than the vacuum saturation test for these particular fine-grained materials. Testing also suggested that specimens with 7-day UCS values below 200 psi will generally not survive freeze-thaw cycling. After both freeze-thaw and vacuum saturation testing, the sand specimens treated with lime-fly ash had significantly higher UCS and retained UCS than specimens treated with Class C fly ash, lime, or cement. Similarly, the clay specimens treated with Class C fly ash or lime-fly ash had significantly higher UCS values than specimens treated with cement or lime; however, clay specimens treated with Class C fly ash and lime-fly ash were not significantly different. None of the four stabilizer types were significantly different from each other with respect to retained UCS after vacuum saturation testing. Dielectric values measured in tube suction testing were lowest for specimens treated with lime-fly ash and cement with respect to the sand and for specimens treated with Class C fly ash and cement with respect to the clay. The lime-fly ash and cement successfully reduced the dielectric value of sand specimens to a "marginal" rating, while no stabilizer reduced the moisture susceptibility of the clay to a satisfactory level. A strong correlation was identified between UCS after the freeze-thaw test and UCS after the vacuum saturation test, while very weak correlations were observed between the final dielectric value after tube suction testing and all other response variables. Differences in variability between test results were determined to be statistically insignificant in an analysis of the CVs associated with data collected in this research. Although the freeze-thaw test utilized in this research was determined to be more severe than the vacuum saturation test for materials similar to those tested in this study, the vacuum saturation test is recommended over both the freeze-thaw and tube suction tests because of the shorter test duration, usability for specimens with 7-day UCS values even below 200 psi, and lack of a need for daily specimen monitoring.

This diploma thesis deals with the issue of the determination of the frost susceptibility of soils in the subgrades of road structures. The theoretical part compares the ways of testing the frost susceptibility in the Czech Republic and other selected countries of the European Union. Furthermore, it also deals with the development of the frost susceptibility index in the Czech Republic. The empirical part focuses on the laboratory testing of the frost susceptibility of the given sample of soil by the direct frost heave method. Moreover, it also deals with the simulation of penetration of frost by the subgrade and the possibility of shortening the length of the freezing during the direct testing the frost susceptibility.

Tato práce se se zabývá návrhem kinematiky zavěšení kol obou náprav. Na základě analýz jízdních dat, multi-body simulací v softwaru Adams Car, simulací v Matlabu a analytických kalkulací v Mathcadu, je navržena řada změn s cílem zlepšit jízdní vlastnosti vozu Formule student, tyto změny jsou následně implementovány do CAD modelu vozu. Jednotlivé změny kinematiky náprav jsou provedeny na základě analýzy konkrétního problému, který se snaží řešit. Jednou z problematik je zástavbová náročnost systému odpružení a zavěšení zadních kol, zde je cílem snížit hmotnost, výšku těžiště a moment setrvačnosti. Další problematikou je geometrie předního kola, kde je cílem zlepšit využití pneumatik a snížit síly v řízení. Dále se práce zabývá simulacemi elastokinematiky zadní nápravy, součástí je také návrh měřícího zařízení. V poslední části je zkoumán vliv provedených změn i elastokinematiky na jízdní dynamiku vozu v ustálených stavech za pomocí MM metody simulované s modelem celého vozu v Adams Car a zpracované v Matlabu.

The work deals with the use of mixed construction recycled material for earth bodies of roads. The theoretical part describes the production, usability and economic evaluation of recycled building materials against common natural materials. It then describes the necessary laboratory tests that examine its properties for the use of these materials in roads. In the last chapter, the work deals with foreign experience with the use of mixed construction recyclates for transport construction. The practical part examines the properties of the given recyclates for their use in the core using tests of soil freezing rate, California bearing ratio and immediate bearing index.

The theoretical part of the diploma thesis searches the production of Construction and demolition waste and their subsequent transformation into the final recyclate and its possible use in roads. Attention is focused on the use of mixed recycled material into subgrade of the pavement and the characteristics of tests that must be performed before its used to the road. The next chapters pai attention to the problematic properties of recyclates, foreign experience with the use of mixed recyclate in Construction and the possibilities of its development. The practical part verifies the suitability of mixed recycled material into subgrade of the pavement using laboratory tests. The tests are performer on individual mixtures of mixed recycled material with cement, blast furnace slag or cement dust in various percentages. The results are then compared and it is evaluated which mixtures show the best properties. Part of the practical part is also the economic evaluation of these mixtures against commonly used materials.