Materials intended for disposal of spent nuclear fuel require a particular combination of physical and chemical properties. The driving forces and mechanisms underlying the material’s behavior must be scientifically understood in order to enable modeling at the relevant time- and length-scales. The processes that determine the mechanical behavior of copper canisters and iron inserts, as well as the evolution of their mechanical properties, are strongly dependent on the properties of various defects in the bulk copper and iron alloys. The first part of the present thesis deals with precipitation in the cast iron insert. A nodular cast iron insert will be used as the inner container of the spent nuclear fuel. Precipitation is investigated by computing effective interaction energies for point defect pairs (solute–solute and vacancy–solute) in bcc iron using first-principles calculations. The main considered impurities in the iron matrix include 3sp (Si, P, S) and 3d (Cr, Mn, Ni, Cu) solute elements. By computing interaction energies possibility of formation of different second phase particles such as late blooming phases (LBPs) in the cast iron insert is evaluated. The second part is devoted to the fundamentals of dislocations and their role in plastic deformation of metals. Deformation of single-crystal copper under high strain rates is simulated by employing dislocation dynamics (DD) method to examine the effect of strain rate on mechanical properties as well as dislocation microstructure development. Creep deformation of copper canister at low temperatures is studied. The copper canister will be used in the long-term storage of spent nuclear fuel as the outer shell of the waste package to provide corrosion protection. A glide rate is derived based on the assumption that at low temperatures it is controlled by the climb rate of jogs on the dislocations. Using DD simulation creep deformation of copper at low temperatures is modeled by taking glide but not climb into account. Moreover, effective stresses acting on dislocations are computed using the data extracted from DD simulations. / <p>QC 20170428</p>

This investigation is focused on the understanding of mechanical and chemical reaction behaviors of stoichiometric mixtures of nano- and micro-scale aluminum and hematite (Fe2O3) powders dispersed in epoxy. Epoxy-cast Al+Fe2O3 thermite composites are an example of a structural energetic material that can simultaneously release energy while providing structural strength. The structural and energetic response of this material system is investigated by characterizing the mechanical behavior under high-strain rate and shock loading conditions. The mechanical response and reaction behavior are closely interlinked through deformation characteristics. It is, therefore, desirable to understand the deformation behavior up to and beyond failure and establish the necessary stress and strain states required for initiating chemical reactions. The composite s behavior has been altered by changing two main processing parameters; the reactants particle size and the relative volume fraction of the epoxy matrix. This study also establishes processing techniques necessary for incorporating nanometric-scale reactants into energetic material systems. The mechanochemical behavior of epoxy-cast Al+Fe2O3 composites and the influence of epoxy volume fraction have been evaluated for a variety of loading conditions over a broad range of strain rates, which include low-strain rate or quasistatic loading experiments (10-4 to 10-2 1/s), medium-strain rate Charpy and Taylor impacts (103 to 104 1/s), and high-strain rate parallel-plate impacts (105 to 106 1/s). In general, structural strength and toughness have been observed to improve as the volume fraction of epoxy decreases, regardless of the loading strain rate regime explored. Hugoniot experiments show damage occurring at approximately the same critical impact stress for compositions prepared with significantly different volume fractions of the epoxy binder phase. Additionally, Taylor impact experiments have indicated evidence for strain-induced chemical reactions, which subject the composite to large shear accompanied by temperature increase and associated softening, preceding these reactions. Overall, the work aims to establish an understanding of the microstructural influence on mechanical behavior and chemical reactivity exhibited by epoxy-cast Al+Fe2O3 materials when exposed to high stress and high-strain loading conditions. The understanding of fundamental aspects and the results of impact experiment measurements provide information needed for the design of structural energetic materials.

Deliberate and accidental explosions along with the heightened risk of loss of life and property damage during such events have highlighted the need for research in the behaviour of materials under high strain rates. Where an extensive body of research is available on steel and concrete structures, little to no details on how to address the design or retrofitting of wood structures subjected to a blast threat are available. Studies reported in the literature that focused on full scale light-frame wood structures did not quantify the increase in capacity due to the dynamic loading while the studies that did quantify the increase mostly stems from small clear specimens that are not representative of the behaviour of structural size members with defects. Tests on larger-scale specimens have mostly focused on the material properties and not the structural behaviour of subsystems. Advancements in design and construction techniques have greatly contributed to the emergence of taller and safer wood structures which increase potential for blast threat. This thesis presents results on the flexural behaviour of light-frame wood stud walls subjected to shock wave loading using the University of Ottawa shock tube. The emphasis is on the overall behaviour of the wall subsystem, especially the interaction between the sheathing and the studs through the nailed connection. The approach employed in this experimental program was holistic, where the specimens were investigated at the component and the subsystem levels. Twenty walls consisting of 38 mm x 140 mm machine stress-rated (MSR) studs spaced 406 mm on center and sheathed with two different types and sheathing thicknesses were tested to failure under static and dynamic loads. The experimental results were used to determine dynamic increase factors (DIFs) and a material predictive model was validated using experimental data. The implications of the code are also discussed and compared to the experimental data. Once validated, an equivalent single-degree-of-freedom (SDOF) model incorporating partial composite action was used to evaluate current analysis and design assumptions. The results showed that a shock tube can effectively be used to generate high strain-rate flexural response in wood members and that the material predictive model was found suitable to effectively predict the displacement resulting from shock wave loading. Furthermore, it was found that current analysis and design approaches overestimated the wall displacements.

Η σφυρηλάτηση με βολή σωματιδίων (shot peening) είναι μία επιφανειακή κατεργασία που πραγματοποιείται με σκοπό την αύξηση της αντοχής μεταλλικών υλικών και εφαρμόζεται στο τελευταίο στάδιο της γραμμής παραγωγής. Η αύξηση της αντοχής επιτυγχάνεται με την ανάπτυξη θλιπτικών παραμενουσών τάσεων κοντά στην επιφάνεια του υλικού έπειτα από την κρούση σωματιδίων με υψηλές ταχύτητες. Η ανάπτυξη θλιπτικών παραμενουσών τάσεων αυξάνει την αντοχή σε κόπωση, σε εργοδιάβρωση, καθώς και σε άλλες μηχανικές καταπονήσεις και επιτρέπει την μείωση του βάρους σχεδιάζοντας διατομές με μικρότερο πάχος. Στην παρούσα Διδακτορική Διατριβή παρουσιάζεται μια ολοκληρωμένη αριθμητική προσομοίωση της κατεργασίας και εξετάζεται η μηχανική συμπεριφορά των υπό κατεργασία υλικών σε υψηλούς ρυθμούς καταπόνησης. Συγκεκριμένα η μεθοδολογία που αναπτύσσεται περιλαμβάνει την ανάπτυξη ενός αριθμητικού προτύπου για την προσομοίωση της κατεργασίας της σφυρηλάτησης με βολή σωματιδίων και τον υπολογισμό των αποτελεσμάτων της στο υλικό. Τα βήματα που ακολουθηθήκαν για την ανάπτυξη του αριθμητικού προτύπου είναι, α) ο χαρακτηρισμός του κράματος αλουμινίου 7449-Τ7651 σε υψηλούς ρυθμούς καταπόνησης μέσω της πειραματικής διάταξης Split Hopkinson Bar που σχεδιάστηκε και κατασκευάστηκε στο Εργαστήριο Τεχνολογίας και Αντοχής Υλικών, β) η ανάπτυξη βοηθητικών επιμέρους αριθμητικών μοντέλων, γ) η ανάπτυξη κινηματικών μοντέλων προσομοίωσης της ροής των σωματιδίων, δ) η ανάπτυξη κριτηρίων και η εφαρμογή τους για τον υπολογισμό του ελαχίστου απαιτούμενου αριθμού σωματιδίων για την προσομοίωση, καθώς και των θέσεων κρούσης, ε) η ανάπτυξη ενός αριθμητικού προτύπου πλήρους γεωμετρίας της πλάκας για την κρούση του απαιτούμενου αριθμού σωματιδίων και στ) η πειραματική επαλήθευση του αριθμητικού προτύπου. Με το αριθμητικό πρότυπο που αναπτύχτηκε υπολογίστηκαν τα αποτελέσματα της κατεργασίας της σφυρηλάτησης με βολή σωματιδίων στο υλικό και επιβεβαιώθηκαν μέσω συγκρίσεων με αντίστοιχα πειραματικά αποτελέσματα. Αποτελέσματα της κατεργασίας εκτός από τις παραμένουσες τάσεις αποτελούν και η πλαστική παραμόρφωση, η σκληρότητα, η επιφανειακή τραχύτητα και κατ' επέκταση ο συντελεστής έντασης τάσης. Στη συνέχεια, πραγματοποιήθηκε μια παραμετρική μελέτη για την επίδραση της διαμέτρου, της ταχύτητας και της γωνίας κρούσης στην ανάπτυξη των παραμενουσών τάσεων. Επίσης το αριθμητικό πρότυπο επαληθεύτηκε και για άλλα μεταλλικά υλικά. / Shot peening is a surface treatment process that is performed to increase the strength of metallic materials and is applied to the last stage of the production line (post manufacturing process). The increase in strength is achieved by the developed compressive residual stresses near the surface and the subsurface of the treated material after the impact of small diameter particles with high speeds. The developed compressive residual stresses increases the fatigue strength, the mechanical performance of the component under stress corrosion cracking (SCC), under higher stresses and allows lighter structure design. This PhD thesis presents a comprehensive numerical simulation of the Shot peening process and includes a comprehensive study of the mechanical behaviour of treated materials under high strain rates of deformation. Specifically, the methodology developed includes the development of a comprehensive numerical model to simulate Shot peening treatment and calculate the results on the treated material. The steps followed for the development of the numerical model are: a) the characterization of the Aluminium alloy 7449-T7651 at high strain rates using a Split Hopkinson Bar apparatus designed and built at the Laboratory of Technology and Strength of Materials, b) the development of auxiliary partial numerical models, c) the development of a kinematic simulation model for the analysis of the flow particles, d) the development and the application of two criteria for the successful calculation of the minimum number of particles that required for the simulation, and the impact positions e) the development of a numerical model describing the full plate geometry for the impact of the minimum number of particles required and f) the experimental verification of the numerical model. The process outcomes and results on the treated material were calculated by the numerical model developed. The numerical results that were calculated for the threaded material were confirmed by comparison with experimental results. Treatment results include the residual stresses, the plastic deformation, hardness, surface roughness, and hence the stress concentration factor. A parametric study on the effect of the diameter, speed and angle of impact to the development of residual stresses was performed. The numerical model was also verified for a number of other metallic materials.

Deliberate and accidental explosions along with the heightened risk of loss of life and property damage during such events have highlighted the need for research in the behaviour of materials under high strain rates. Where an extensive body of research is available on steel and concrete structures, little to no details on how to address the design or retrofitting of wood structures subjected to a blast threat are available. Studies reported in the literature that focused on full scale light-frame wood structures did not quantify the increase in capacity due to the dynamic loading while the studies that did quantify the increase mostly stems from small clear specimens that are not representative of the behaviour of structural size members with defects. Tests on larger-scale specimens have mostly focused on the material properties and not the structural behaviour of subsystems. Advancements in design and construction techniques have greatly contributed to the emergence of taller and safer wood structures which increase potential for blast threat. This thesis presents results on the flexural behaviour of light-frame wood stud walls subjected to shock wave loading using the University of Ottawa shock tube. The emphasis is on the overall behaviour of the wall subsystem, especially the interaction between the sheathing and the studs through the nailed connection. The approach employed in this experimental program was holistic, where the specimens were investigated at the component and the subsystem levels. Twenty walls consisting of 38 mm x 140 mm machine stress-rated (MSR) studs spaced 406 mm on center and sheathed with two different types and sheathing thicknesses were tested to failure under static and dynamic loads. The experimental results were used to determine dynamic increase factors (DIFs) and a material predictive model was validated using experimental data. The implications of the code are also discussed and compared to the experimental data. Once validated, an equivalent single-degree-of-freedom (SDOF) model incorporating partial composite action was used to evaluate current analysis and design assumptions. The results showed that a shock tube can effectively be used to generate high strain-rate flexural response in wood members and that the material predictive model was found suitable to effectively predict the displacement resulting from shock wave loading. Furthermore, it was found that current analysis and design approaches overestimated the wall displacements.

Plasticity in crystalline solids is controlled by the microscopic line defects known as “dislocations”. Decisive role of dislocations in crystal plasticity in addition to fundamentals of plastic deformation are presented in the current thesis work. Moreover, major features of numerical modeling method “Discrete Dislocation Dynamics (DDD)” technique are described to elucidate a powerful computational method used in simulation of crystal plasticity. First part of the work is focused on the investigation of strain rate effect on the dynamic deformation of crystalline solids. Single crystal copper is chosen as a model crystal and discrete dislocation dynamics method is used to perform numerical uniaxial tensile test on the single crystal at various high strain rates. Twenty four straight dislocations of mixed character are randomly distributed inside a model crystal with an edge length of 1 µm subjected to periodic boundary conditions. Loading of the model crystal with the considered initial dislocation microstructure at constant strain rates ranging from 103 to 105s1 leads to a significant strain rate sensitivity of the plastic flow. In addition to the flow stress, microstructure evolution of the sample crystal demonstrates a considerable strain rate dependency. Furthermore, strain rate affects the strain induce microstructure heterogeneity such that more heterogeneous microstructure emerges as strain rate increases. Anisotropic characteristic of plasticity in single crystals is investigated in the second part of the study. Copper single crystal is selected to perform numerical tensile tests on the model crystal along two different loading directions of [001] and [111] at two high strain rates. Effect of loading orientation on the macroscopic behavior along with microstructure evolution of the model crystal is examined using DDD method. Investigation of dynamic response of single crystal to the mechanical loading demonstrates a substantial effect of loading orientation on the flow stress. Furthermore, plastic anisotropy is observed in dislocation density evolution such that more dislocations are generated as straining direction of single crystal is changed from [001] to [111] axis. Likewise, strain induced microstructure heterogeneity displays the effect of loading direction such that more heterogeneous microstructure evolve as single crystal is loaded along [111] direction. Formation of slip bands and consequently localization of plastic deformation are detected as model crystal is loaded along both directions. / <p>QC 20151015</p>

No description available.

An investigation of the microstructure-mechanical property relationships for gray cast iron and a vintage ASTM A7 steel are presented herein. Gray cast iron was shown to have a moderate sensitivity to strain rate and a large disparity in behavior between compression, tension, and torsion. ASTM A7 steel was shown to behave in a more complex manor with the strain rate sensitivity having a negative relationship in tension and positive relationship in compression and torsion, the tensile stress-state producing the highest stress response, and the material producing a higher stress response when exposed to elevated temperatures. The counterintuitive behavior observed in A7 steel was attributed to dynamic strain aging. The Mississippi State University Internal State Variable Plasticity-Damage model was updated to accurately capture negative strain rate sensitivity and DSA embrittlement by developing kinematic, thermodynamic, and kinetic constitutive relationships for dynamic strain aging. A parametric study was performed to elucidate the behavior of the new internal state variable for dynamic strain aging. Gray cast iron was successfully calibrated to a pre-DSA version of the plasticity-damage model and A7 steel was successfully calibrated to the updated plasticity-damage model.

No description available.

No description available.