KBS-3 and very deep borehole (VDH) concepts are two major types of long-term geologicaldisposal methods for high-level radioactive waste (HLW) isolating from the biosphere. TheKBS-3V concept for isolating the HLW at the depth of 400-500 m, is the officially proposedoption in Sweden and has been the subject of considerable research in the past few decades,while the VDH concept was considered as an option in the 1950s but later became discouragedbecause of insufficient experience in drilling technology. The greatest merit of the VDHconcept is that the almost stagnant groundwater in the deep boreholes prevents the transport ofthe possible release of radionuclides into the rock or up to the ground level. Since variousdisadvantages of the KBS-3V concept were found in previous research, the superiority of VDHconcept attracted the researchers to continue studying it into the late 1980s.The geological repositories of both of KBS-3V and VDH types primarily consist of a naturalbarrier (host rock) and of an engineering barrier (also known as a buffer/backfill barrier).According to the principle of IAEA and national relative research organizations, thebuffer/backfill material should have low permeability and good expandability, as well assuitable physical and sealing properties.The thesis concerns the VDH concept and is focused on the construction and performance ofthose parts of the sealed repository that are not affected by high temperature or gamma radiation.In the lower part of a VDH repository, the clay packages containing HLW will be exposed tohigh temperature (100-150 􀄇 ) in the borehole and to highly saline groundwater. In theinstallation phase of HLW, the groundwater will be pumped out and replaced by medium-softsmectite clay mud in which the HLW packages are installed vertically. During the hydrationand maturation of the clay components, the microstructural reorganization, water transport,migration of clay particles and redistribution of the density of the components take place. Thematuration determines the transient evolution of the clay seals and influences the rheologicaland soil mechanical behavior in the installation phase. The maturation of clay system alsodetermines their ultimate sealing potential of VDH repositories.This study presents the work carried out for investigating the maturation of the buffer-backfillclay in the HLW deep borehole. Initially in the study three types of clays, the Namontmorillonite,magnesium-rich and illite-smectite mixed layer clays, were examined for estimating their performance as the barrier candidate material. This is mainly presented in theliterature review. The experimental study was conducted on montmorillonite GMZ clays andI/S mixed-layer Holmehus clay. The expandability and permeability tests were carried out forinterpretation of the recorded swelling development and assessment of the effect of the salineconditions, with the goal of deriving a relationship between swelling pressure and hydraulicconductivity for different dry densities. The maturation tests of initially fully-saturatedHolmehus clay and partly saturated GMZ clay were performed. During the tests, the shearstrength mobilised by the relative movement of densified mud and migrated dense clay -contained in a perforated central tube - were determined. According to the results of shearstrength tests, the maximum operation time or the number of clay packages to be placed in asingle operation was evaluated, whilst the suitable saturation degree of the dense clay wasdiscussed as well.A model of the maturation of initially water-saturated clay seals based on Darcy’s law wasworked out and the evolution of the clay components in a lab-scale borehole using Holmehusclay were performed and compared with the experimental recordings. Good agreementsbetween the physical behaviors of the theoretical simulations and the measurements wasachieved by which the validity of the model was verified. Using the results, the hydration andsoil migration in the entire maturation process were presented in diagram. The model was alsoused for preliminary evaluation of the maturation products in real boreholes by assuming thesame Holmehus clay as used in the tests. Two constellation of borehole and dense clay withdifferent diameters, 80 cm borehole /60 cm clay and 80cm/50cm, were assumed. The resultsrespecting dry density and hydraulic conductivity of the ultimate maturation products, and thedegree of homogeneous of the buffer and backfill clay system in the assumed boreholes, arepresented and discussed. The options of different mineral types and initial physical propertiesof the candidate buffer clays provide a reference for engineering barrier design of HLW disposalin VDH.

Deep geological repository (DGR) for disposal of high-level radioactive waste (HLW) is designed to rely on successive superimposed barrier systems to isolate the waste from the biosphere. This multiple barrier system comprises the natural geological barrier provided by the repository host rock and its surrounding and an engineered barrier system (EBS). The EBS represents the synthetic, engineered materials placed within the natural barrier, comprising array of components such as waste form, waste canisters, buffer materials, backfill and seals. The buffer will enclose the waste canisters from all directions and act as a barrier between canisters and host rock of the repository. It is designed to stabilise the evolving thermo-hydro-mechanical-chemical stresses in the repository over a long period (nearly 1000 years) to retard radionuclides from reaching biosphere. Bentonite clay or bentonite-sand mix have been chosen as buffer materials in EBS design in various countries pursuing deep geological repository method. The bentonite buffer is the most important barrier among the other EBS components for a geological repository. The safety of repository depends to a large extent on proper functioning of buffer over a very long period of time during which it must remain physically, chemically and mineralogically stable. The long term stability of bentonite buffer depends on varying temperature and evolution of groundwater composition of host rocks in a complex way. The groundwater in the vicinity of deep crystalline rock is often characterized by high solute concentrations and the geotechnical engineering response of bentonite buffer could be affected by the dissolved salt concentration of the inflowing ground water. Also during the initial period, radiogenic heat produced in waste canisters would radiate into buffer and the heat generated would lead to drying and some shrinkage of bentonite buffer close to canister. This could alter the dry density, moisture content and in turn the hydro-mechanical properties of bentonite buffer in DGR conditions. India has variety of bentonite deposits in North-Western states of Rajasthan and Gujarat. Previous studies on Indian bentonites suggest that bentonite from Barmer district of Rajasthan (termed as Barmer-1 bentonite) is suitable to serve as buffer material in DGR conditions. Nuclear power agencies of several countries have identified suitable bentonites for use as buffer in DGR through laboratory experiments and large scale underground testing facilities. Physico-chemical, mineralogical and engineering properties of Kunigel VI, Kyungju, GMZ, FoCa clay, MX-80, FEBEX and Avonseal bentonites have been extensively studied by Japan, South Korea, China, Belgium, Sweden, Spain, Canada. It is hence essential to examine the suitability of Barmer-1 bentonite as potential buffer in DGR and compare its physico-chemical and hydromechanical properties with bentonite buffers identified by other countries. The significant factors that impact the long-term stability of bentonite buffer in DGR include variations in moisture content, dry density and pore water chemistry. With a view to address these issues, the hydromechanical response of 70 % Barmer-1 bentonite + 30 % river sand mix (termed bentonite enhanced sand, BES specimens) under varying moisture content, dry density and pore water salt concentration conditions have been examined. The broad scope of the work includes: 1) Characterise the physico-chemical and hydro-mechanical properties of Barmer-1 bentonite from Rajasthan, India and compare its properties with bentonite buffers reported in literature. 2) Examine the influence of variations in dissolved salt concentration (of infiltrating solution), dry density and moisture content of compacted BES specimens on their hydro-mechanical response; the hydro-mechanical properties include, swell pressure, soil water characteristic curve (SWCC), unsaturated hydraulic conductivity, moisture diffusivity and unconfined compression strength. Organization of thesis: After the first introductory chapter, a detailed review of literature is performed to highlight the need for detailed characterisation of physico-chemical and hydromechanical properties of Barmer-1 bentonite for its possible application in DGR in the Indian context. Further, existing literature on hydro-mechanical response of bentonite buffer to changes in physical (degree of saturation/moisture content, dry density) and physico-chemical (solute concentration in pore water) is reviewed to define the scope and objectives of the present thesis in Chapter 2. Chapter 3 presents a detailed experimental programme of the study. Chapter 4 characterises Barmer-1 bentonite for physico-chemical (cation exchange capacity, pore water salinity, exchangeable sodium percentage) and hydro-mechanical properties, such as, swell pressure, saturated permeability, soil water characteristic curve (SWCC) and unconfined compression strength. The properties of Barmer-1 bentonite are compared with bentonite buffers reported in literature and generalized equations for determining swell pressure and saturated permeability coefficient of bentonite buffers are arrived at. Chapter 5 describes a method to determine solute concentrations in the inter-lamellar and free-solutions of compacted BES (bentonite enhanced sand) specimens. The solute concentrations in micro and macro pore solutions are used to examine the role of osmotic flow on swell pressures developed by compacted BES specimens (dry density 1.50-2.00 Mg/m3) inundated with distilled water and NaCl solutions (1000-5000 mg/L). The number of hydration layers developed by the compacted BES specimens on inundation with salt solutions in constant volume swell pressure tests is controlled by cation hydration/osmotic flow. The cation hydration of specimens compacted to dry density of 2.00 Mg/m3 is mainly driven by matric suction prevailing in the clay microtructure as the number of hydration layers developed at wetting equilibrium are independent of the total dissolved solids (TDS) of the wetting solution. Consequently, the swell pressures of specimens compacted to 2.00 Mg/m3 were insensitive to the salt concentration of the inundating solution. The cation hydration of specimens compacted to dry density of 1.50 Mg/m3 is driven by both matric suction (prevailing in the clay micro-structure) and osmotic flow as the number of hydration layers developed at wetting equilibrium is sensitive to the TDS of the wetting solution. Expectedly, the swell pressures of specimens compacted to 1.50 Mg/m3 responded to changes in salt concentration of the inundating solution. The 1.75 Mg/m3 specimens show behaviour that is intermediate to the 1.50 and 2.00 Mg/m3 series specimens. Chapter 6 examines the influence of initial degree of saturation on swell pressures developed by the compacted BES specimens (dry density range: 1.40- 2.00 Mg/m3) on wetting with distilled water from micro-structural considerations. The micro-structure of the bentonite specimens are examined in the compacted and wetted states by performing X-ray diffraction measurements. The initial degree of saturation is varied by adding requisite amount of distilled water to the oven-dried BES mix and compacting the moist mixes to the desired density. The montmorillonite fraction in the BES specimens is responsible for moisture absorption during compaction and development of swell pressure in the constant volume oedometer tests. Consequently, it was considered reasonable to calculate degree of saturation based on EMDD (effective montmorillonite dry density) values and correlate the developed swell pressure values with degree of saturation of montmorillonite voids (Sr,MF). XRD measurements with compacted and wetted specimens demonstrated that if specimens of density series developed similar number of hydration layers on wetting under constant volume condition they exhibited similar swell pressures, as was the case for specimens belonging to 1.40 and 1.50 Mg/m3 series. With specimens belonging to 1.75 and 2.00 Mg/m3 series, greater number of hydration layers were developed by specimens that were less saturated initially (smaller initial Sr,MF) and consequently such specimens developed larger swell pressures. When specimens developed similar number of hydration layers in the wetted state, the compaction dry density determined the swell pressure. Chapter 7 examines the influence of salt concentration of infiltrating solution (sodium chloride concentration ranges from 1000- 5000 mg/L) on SWCC relations, unsaturated permeability and moisture diffusivity of compacted BES specimens. Analysis of the experimental and Brooks and Corey best fit plots revealed that infiltration of sodium chloride solutions had progressively lesser influence on the micro-structure and consequently on the SWCC relations with increase in dry density of the compacted specimens. The micro-structure and SWCC relations of specimens compacted to 1.50 Mg/m3 were most affected, specimens compacted to 1.75 Mg/m3 were less affected, while specimens compacted to 2.00 Mg/m3 were unaffected by infiltration of sodium chloride solutions. Variations in dry density of compacted bentonite impacts the pore space available for moisture flow, while, salinity of wetting fluid impacts the pore structure from associated physico-chemical changes in clay structure. Experimental results showed that the unsaturated permeability coefficient is insensitive to variations in dry density and solute concentration of wetting liquid, while, the effective hydraulic diffusivity is impacted by variations in these parameters. Chapter 8 summarises the major findings of the study.

Deep geological repository (DGR) for disposal of high-level radioactive waste (HLW) is designed to rely on successive superimposed barrier systems to isolate the waste from the biosphere. This multiple barrier system comprises the natural geological barrier provided by the repository host rock and its surrounding and an engineered barrier system (EBS). The EBS represents the synthetic, engineered materials placed within the natural barrier, comprising array of components such as waste form, waste canisters, buffer materials, backfill and seals. The buffer will enclose the waste canisters from all directions and act as a barrier between canisters and host rock of the repository. It is designed to stabilise the evolving thermo-hydro-mechanical-chemical stresses in the repository over a long period (nearly 1000 years) to retard radionuclides from reaching biosphere. Bentonite clay or bentonite-sand mix have been chosen as buffer materials in EBS design in various countries pursuing deep geological repository method. The bentonite buffer is the most important barrier among the other EBS components for a geological repository. The safety of repository depends to a large extent on proper functioning of buffer over a very long period of time during which it must remain physically, chemically and mineralogically stable. The long term stability of bentonite buffer depends on varying temperature and evolution of groundwater composition of host rocks in a complex way. The groundwater in the vicinity of deep crystalline rock is often characterized by high solute concentrations and the geotechnical engineering response of bentonite buffer could be affected by the dissolved salt concentration of the inflowing ground water. Also during the initial period, radiogenic heat produced in waste canisters would radiate into buffer and the heat generated would lead to drying and some shrinkage of bentonite buffer close to canister. This could alter the dry density, moisture content and in turn the hydro-mechanical properties of bentonite buffer in DGR conditions. India has variety of bentonite deposits in North-Western states of Rajasthan and Gujarat. Previous studies on Indian bentonites suggest that bentonite from Barmer district of Rajasthan (termed as Barmer-1 bentonite) is suitable to serve as buffer material in DGR conditions. Nuclear power agencies of several countries have identified suitable bentonites for use as buffer in DGR through laboratory experiments and large scale underground testing facilities. Physico-chemical, mineralogical and engineering properties of Kunigel VI, Kyungju, GMZ, FoCa clay, MX-80, FEBEX and Avonseal bentonites have been extensively studied by Japan, South Korea, China, Belgium, Sweden, Spain, Canada. It is hence essential to examine the suitability of Barmer-1 bentonite as potential buffer in DGR and compare its physico-chemical and hydromechanical properties with bentonite buffers identified by other countries. The significant factors that impact the long-term stability of bentonite buffer in DGR include variations in moisture content, dry density and pore water chemistry. With a view to address these issues, the hydromechanical response of 70 % Barmer-1 bentonite + 30 % river sand mix (termed bentonite enhanced sand, BES specimens) under varying moisture content, dry density and pore water salt concentration conditions have been examined. The broad scope of the work includes: 1) Characterise the physico-chemical and hydro-mechanical properties of Barmer-1 bentonite from Rajasthan, India and compare its properties with bentonite buffers reported in literature. 2) Examine the influence of variations in dissolved salt concentration (of infiltrating solution), dry density and moisture content of compacted BES specimens on their hydro-mechanical response; the hydro-mechanical properties include, swell pressure, soil water characteristic curve (SWCC), unsaturated hydraulic conductivity, moisture diffusivity and unconfined compression strength. Organization of thesis: After the first introductory chapter, a detailed review of literature is performed to highlight the need for detailed characterisation of physico-chemical and hydromechanical properties of Barmer-1 bentonite for its possible application in DGR in the Indian context. Further, existing literature on hydro-mechanical response of bentonite buffer to changes in physical (degree of saturation/moisture content, dry density) and physico-chemical (solute concentration in pore water) is reviewed to define the scope and objectives of the present thesis in Chapter 2. Chapter 3 presents a detailed experimental programme of the study. Chapter 4 characterises Barmer-1 bentonite for physico-chemical (cation exchange capacity, pore water salinity, exchangeable sodium percentage) and hydro-mechanical properties, such as, swell pressure, saturated permeability, soil water characteristic curve (SWCC) and unconfined compression strength. The properties of Barmer-1 bentonite are compared with bentonite buffers reported in literature and generalized equations for determining swell pressure and saturated permeability coefficient of bentonite buffers are arrived at. Chapter 5 describes a method to determine solute concentrations in the inter-lamellar and free-solutions of compacted BES (bentonite enhanced sand) specimens. The solute concentrations in micro and macro pore solutions are used to examine the role of osmotic flow on swell pressures developed by compacted BES specimens (dry density 1.50-2.00 Mg/m3) inundated with distilled water and NaCl solutions (1000-5000 mg/L). The number of hydration layers developed by the compacted BES specimens on inundation with salt solutions in constant volume swell pressure tests is controlled by cation hydration/osmotic flow. The cation hydration of specimens compacted to dry density of 2.00 Mg/m3 is mainly driven by matric suction prevailing in the clay microtructure as the number of hydration layers developed at wetting equilibrium are independent of the total dissolved solids (TDS) of the wetting solution. Consequently, the swell pressures of specimens compacted to 2.00 Mg/m3 were insensitive to the salt concentration of the inundating solution. The cation hydration of specimens compacted to dry density of 1.50 Mg/m3 is driven by both matric suction (prevailing in the clay micro-structure) and osmotic flow as the number of hydration layers developed at wetting equilibrium is sensitive to the TDS of the wetting solution. Expectedly, the swell pressures of specimens compacted to 1.50 Mg/m3 responded to changes in salt concentration of the inundating solution. The 1.75 Mg/m3 specimens show behaviour that is intermediate to the 1.50 and 2.00 Mg/m3 series specimens. Chapter 6 examines the influence of initial degree of saturation on swell pressures developed by the compacted BES specimens (dry density range: 1.40- 2.00 Mg/m3) on wetting with distilled water from micro-structural considerations. The micro-structure of the bentonite specimens are examined in the compacted and wetted states by performing X-ray diffraction measurements. The initial degree of saturation is varied by adding requisite amount of distilled water to the oven-dried BES mix and compacting the moist mixes to the desired density. The montmorillonite fraction in the BES specimens is responsible for moisture absorption during compaction and development of swell pressure in the constant volume oedometer tests. Consequently, it was considered reasonable to calculate degree of saturation based on EMDD (effective montmorillonite dry density) values and correlate the developed swell pressure values with degree of saturation of montmorillonite voids (Sr,MF). XRD measurements with compacted and wetted specimens demonstrated that if specimens of density series developed similar number of hydration layers on wetting under constant volume condition they exhibited similar swell pressures, as was the case for specimens belonging to 1.40 and 1.50 Mg/m3 series. With specimens belonging to 1.75 and 2.00 Mg/m3 series, greater number of hydration layers were developed by specimens that were less saturated initially (smaller initial Sr,MF) and consequently such specimens developed larger swell pressures. When specimens developed similar number of hydration layers in the wetted state, the compaction dry density determined the swell pressure. Chapter 7 examines the influence of salt concentration of infiltrating solution (sodium chloride concentration ranges from 1000- 5000 mg/L) on SWCC relations, unsaturated permeability and moisture diffusivity of compacted BES specimens. Analysis of the experimental and Brooks and Corey best fit plots revealed that infiltration of sodium chloride solutions had progressively lesser influence on the micro-structure and consequently on the SWCC relations with increase in dry density of the compacted specimens. The micro-structure and SWCC relations of specimens compacted to 1.50 Mg/m3 were most affected, specimens compacted to 1.75 Mg/m3 were less affected, while specimens compacted to 2.00 Mg/m3 were unaffected by infiltration of sodium chloride solutions. Variations in dry density of compacted bentonite impacts the pore space available for moisture flow, while, salinity of wetting fluid impacts the pore structure from associated physico-chemical changes in clay structure. Experimental results showed that the unsaturated permeability coefficient is insensitive to variations in dry density and solute concentration of wetting liquid, while, the effective hydraulic diffusivity is impacted by variations in these parameters. Chapter 8 summarises the major findings of the study.